similar to: 2 different APC UPS using USB get in power off recoverable state

Hi debian jessie, nut 2.7.2-4 APC Smart-UPS 1500 connected through USB, running nut driver usbhid-ups This UPS powers my switches, internet connection and my monitor server that monitors this and my other UPSes + runs smokeping and nagios. But recently a powerloss seemed to have shutdown my monitor PC immediately, so it did not shut down the other servers cleanly. Power seem to be lost

On 03/04/17 17.24, Roger Price wrote: > On Mon, 3 Apr 2017, Jon Bendtsen wrote: > >> On 03/04/17 17.10, Roger Price wrote: >>> On Mon, 3 Apr 2017, Jon Bendtsen wrote: >>> >>>> Power seem to be lost immediately. >>>> But my APC Smart-UPS 1500 always reported everything OK. >>>> battery.charge : 100 >>> ...

hi NUT 2.4.3 on new server can not see serial number, but old nut on different hardware can? I have 2 USB-hid ups from APC, 1500 and 3000 RM, i use the serial number to identify them. However my new UPS monitor server can not see the serial number? It works on Linux dkserver 2.6.22.18-vs2.2.0.6 #1 SMP Sat Feb 16 20:54:32 CET 2008 i686 GNU/Linux debian package 2.2.2-6.5 it does not work on

On the basis of continuing experience, one final piece of R3000XR battery pack advice: After swapping the R3000XR battery pack, power-cycle the UPS, wait until the battery pack is at least 50% charged, then disconnect the UPS from wall power for a minute or so before plugging it back in. Until I did this, my UPS would charge the battery pack fully, then let it slowly self-discharge. After

This is not a NUT question per se ... or at least, I don't think it is. I just replaced the battery pack in my HP R3000XR; the new batteries were shipped with 90% charge, were at about 87% when they went in, and were up to 98% charge the next day. Last weekend, the server that runs NUT went down for no apparent reason, wiping out its boot blocks, corrupting its boot archive beyond

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello everybody, I have a Debian network server doing monitoring for three UPS devices. > MONITOR r3000xr at localhost 1 monuser xxxxxxxxxx master > MONITOR apcups01 at localhost 1 monuser xxxxxxxxx monitor-only > MONITOR apcups02 at localhost 1 monuser xxxxxxxxx monitor-only I want nut to send an email to root for every changes nut

Hi, I have an HP R5500XR and a Compaq R3000XR that I would like to use with nut. I searched the compatibility lists and the mail list archives but couldn't find anything. They both have 9 pin serial ports. Can anyone give me any information about them, and if they are supported by nut? Thanks, Denny Fox

Greetings, I've just installed nut-2.4.1 on a Solaris 10 x86 machine to monitor a HP R3000XR UPS. SunOS babylon4 5.10 Generic_138889-08 i86pc i386 i86pc Solaris First of all, I encountered a single problem during the build. After configuring, drivers/Makefile ends up containing the following line: LIBNETSNMP_LDFLAGS = -R../lib -L/usr/sfw/lib -lnetsnmp -lgen [...] This is clearly

I seem to have NUT all working with my R3000XR, except for the CGIs. The webserver's all properly configured and upsstats.cgi *runs*, but doesn't yield any useful output - no values are displayed, every value is replaced by [error: Invalid argument]. Apache is not logging any resulting errors, and there doesn't seem to be a lot of useful documentation on the CGIs to troubleshoot

On 07/08/2013, at 13.40, Jan Phillip Greimann <jg at softjury.de> wrote: > Hi there, > > OS: (L)ubuntu 12.04 precise LTS > Nut: 2.6.3-1ubuntu1.1 > Installation Method: Package (apt-get install nut) > Hardware: HP R1500 G3 INT FYI: I have a different UPS, a HP R3000 XR and I monitor it using serial and the bcmxcp driver. [R3000XR] port = /dev/ttyUSB0 driver =

On 10/04/17 15.25, Jon Bendtsen wrote: > On 04/04/17 15.19, Arnaud Quette wrote: >> >> >> 2017-04-04 14:18 GMT+02:00 Jon Bendtsen <jon.bendtsen at jonix.dk >> <mailto:jon.bendtsen at jonix.dk>>: [cuuuuut] > I'd say your change is a success :-) well, almost, but maybe that is outside NUT's control. /usr/lib/nagios/plugins/check_ups -H

On 08/08/2013, at 18.58, Alf H?gemark <alf at i100.no> wrote: > On 08/07/2013 02:02 PM, Bendtsen, Jon wrote: >> On 07/08/2013, at 13.40, Jan Phillip Greimann <jg at softjury.de> wrote: >> >>> Hi there, >>> >>> OS: (L)ubuntu 12.04 precise LTS >>> Nut: 2.6.3-1ubuntu1.1 >>> Installation Method: Package (apt-get install nut)

Hello everybody, I got tree UPS devices connected to a Debian server, and i am searching for a way to configure them. The server power-cord is only connected to one of the ups devices, and should monitor the other ups systems to sent email status. I got a HP R3000XR UPS with has a RS232 communication port that I have working perfectly. Then I have two APC SmartUPS 750V devices that are

On 08/07/2013 02:02 PM, Bendtsen, Jon wrote: > On 07/08/2013, at 13.40, Jan Phillip Greimann <jg at softjury.de> wrote: > >> Hi there, >> >> OS: (L)ubuntu 12.04 precise LTS >> Nut: 2.6.3-1ubuntu1.1 >> Installation Method: Package (apt-get install nut) >> Hardware: HP R1500 G3 INT > > FYI: > I have a different UPS, a HP R3000 XR and I monitor

Hi Charles, Thanks for your response. > For the 1000, do the values match this page? > > > http://buildbot.networkupstools.org/~buildbot/cayman/docs/latest/ddl/APC/Smart-UPS_1000.html > > Yes it does (except that mine is a 120 V model, so input/output voltage is about 125) It doesn't look like we have an entry for a C1500 yet. Would you care to > submit the output of

On Nov 8, 2014, at 6:12 PM, Selva Nair <selva.nair at gmail.com> wrote: > Everything works rather well, except that the cgi-interface does not report input/output voltages and load for the C 1500 unit. > upsc also reports these values only for model 1000, not for 1500. Battery charge is and runtime are reported. For the 1000, do the values match this page?

I posted earlier about a problem with a HP R3000XR that was showing abnormally low charge a couple of days after replacing the battery pack. For those with R3000XRs, the progblem seems to be: (1) while you CAN hot-swap the battery-pack on an R3000XR, the UPS automatically goes into bypass mode when you do so; (2) it doesn't necessarily come OUT of bypass mode after you install the

Hi, I have setup NUT in netserver mode on debian wheezy with two APC UPS units connected to it by usb. lsusb identifies the units as Smart-UPS 1000 and Smart-UPS C1500. It appears these do not use the smart protocol and usbhid-ups is the correct driver to use. System: Debian wheezy with stock version of nut (Version: 2.6.4-2.3+deb7u1) Everything works rather well, except that the

Hi all, I am trying to get a APC Back-UPS CS 500 running on my QNAP 419P Nas. Since on all my work I figure out the following: from Network UPS Tools upscmd 2.4.1 [~] # upscmd -l qnapups Instant commands supported on UPS [qnapups]: beeper.disable - Disable the UPS beeper beeper.enable - Enable the UPS beeper beeper.mute - Temporarily mute the UPS beeper beeper.off - Obsolete (use

On 04/04/17 15.19, Arnaud Quette wrote: > > > 2017-04-04 14:18 GMT+02:00 Jon Bendtsen <jon.bendtsen at jonix.dk > <mailto:jon.bendtsen at jonix.dk>>: [cuuuuut] > > there is a Github issue: https://github.com/networkupstools/nut/issues/415 > + a branch with the implementation: > https://github.com/networkupstools/nut/tree/upsmon_alarm > > For now: > -