similar to: WG: Which version of CTDB

Hi, I am setting up a two node Samba cluster with CTDB in AWS in two different subnets. All IP ports are open between these two subnets. I am initially forming the Samba cluster with one node, then will add the second node after startup of CTDB. I am not using public_addresses for CTDB due to AWS not supporting VIP's. I am using 64bit Amazon Linux with two NICs defined, eth0 as the

Hello, i'm still trying to find out what is the right path for ctdb.conf (ubuntu 18.04, samba was compiled from source!!). When im trying to start CTDB without any config file, my log in /usr/local/samba/var/log/log.ctdb shows me: 2018/05/07 12:56:44.363513 ctdbd[4503]: Failed to read nodes file "/usr/local/samba/etc/ctdb/nodes" 2018/05/07 12:56:44.363546 ctdbd[4503]: Failed to

Hi, we run ctdb with samba on SLES11. It was running for some month ok but after an update of the system and ctdb it fails to run. I tried to setup a new ctdb setup on two other nodes and it still fails with the same error. After startup the status is: > ctdb status > Number of nodes:2 > pnn:0 10.94.43.7 DISABLED > pnn:1 10.94.43.8 DISABLED (THIS NODE) >

Hello all, I've some CTDB issue which I'm not sure where to start... I follow this guide by steve which is nice. The different on what have is that I don't have drbd running... Also I've 4 x GE which is all Connected to a switch with different ip but same subnet This is suppose to load balance the traffic as under samba dns, they all have the same name. I'm only planing 3

Dear all, after downloading ctdb with rsync -avz samba.org::ftp/unpacked/ctdb and compiling well. I installed on my Centos 5.3 sernet package samba 3.5.2. Also working well. But after setting up ctdb and samba und running it my two nodes freezing for a while And ctdb and samba are down again. On Both nodes My /etc/sysconfig/ctdb: CTDB_RECOVERY_LOCK="/cluster/recovery/recovery"

Hello, at this time i want to install a CTDB Cluster with SAMBA 4.7.7 from SOURCE! I compiled samba as follow: |./configure| |--with-cluster-support ||--with-shared-modules=idmap_rid,idmap_tdb2,idmap_ad| The whole SAMBA enviroment is located in /usr/local/samba/. CTDB is located in /usr/local/samba/etc/ctdb. I guess right that the correct path of ctdbd.conf (node file, public address file

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm trying to bring up a three node cluster using CTDB and SAMBA4 on a GlusterFS clustered file system. The filesystem itself seems to be working just fine, but CTDB doesn't seem happy. If I start a single node up: service ctdb start After about 10 seconds it becomes healthy, starts SAMBA and takes over all 3 IP addresses. However,

There is a 3 nodes ctdb cluster is running. When one of 3 nodes is powered down, lots of logs will be wrote to log.ctdb. node1: repeat logs: 2018/09/04 04:35:06.414369 ctdbd[10129]: Recovery has started 2018/09/04 04:35:06.414944 ctdbd[10129]: connect() failed, errno=111 2018/09/04 04:35:06.415076 ctdbd[10129]: Unable to run startrecovery event node2: repeat logs: 2018/09/04 04:35:09.412368

Am Montag, 26. Februar 2018, 17:26:06 CET schrieb zhu.shangzhong--- via samba: Decoded base64 encoded body with some chinese characters: ------------------原始邮件------------------ 发件人：朱尚忠10137461 收件人：samba at lists.samba.org <samba at lists.samba.org> 日 期 ：2018年02月26日 17:10 主 题 ：[ctdb] Unable to take recovery lock - contention When the ctdb is starting, the "Unable to take recovery lock

When the ctdb is starting, the "Unable to take recovery lock - contention" log will be output all the time. Which cases will the "unable to take lock" errror be output? Thanks! The following the ctdb logs: 2018/02/12 19:38:51.147959 ctdbd[5615]: CTDB starting on node 2018/02/12 19:38:51.528921 ctdbd[6602]: Starting CTDBD (Version 4.6.10) as PID: 6602 2018/02/12 19:38:51.529060

When the ctdb is starting, the "Unable to take recovery lock - contention" log will be output all the time. Which cases will the "unable to take lock" errror be output? Thanks! The following the ctdb logs: 2018/02/12 19:38:51.147959 ctdbd[5615]: CTDB starting on node 2018/02/12 19:38:51.528921 ctdbd[6602]: Starting CTDBD (Version 4.6.10) as PID: 6602 2018/02/12 19:38:51.529060

Can Somebody have a look !? Or an Idea. How bind can resolve the second cname ._mscds. I can take every other cname for my second samba4 but the: a441f8f9-629d-43c4-bce6-a5dfba1e4ad9._msdcs NODE1 is: 02284f45-de16-4125-a795-3b614f540ef7 NODE2 is: a441f8f9-629d-43c4-bce6-a5dfba1e4ad9 So Replication from NODE2 to NODE1 works fine: UpdateRefs OK for

------------------原始邮件------------------ 发件人：朱尚忠10137461 收件人：samba@lists.samba.org <samba@lists.samba.org> 日 期 ：2018年02月26日 17:10 主 题 ：[ctdb] Unable to take recovery lock - contention When the ctdb is starting, the "Unable to take recovery lock - contention" log will be output all the time. Which cases will the "unable to take lock" errror be output? Thanks! The

Hi, I'm trying to set up a small CTDB cluster running in an IPoIB InfiniBand network. When I try to start up a cluster with a set of public IP addresses, the public addresses do not come online. So, I removed the public address configuration and started a single node up by hand, then tried to add a public address as follows: [root at gp-1-0 ctdb]# ctdb ip Public IPs on node 0 [root at

Hello, We are using CTDB / Samba to serve a number of windows users, at this point around 1200. We have a 4 node CTDB setup. CTDB version - ctdb-1.0.114.7-1 Samba Version - sernet-samba-4.1.16-10 In recent months we've seen a big problem when 1 of the CTDB nodes is stopped or disconnected either manually or resulting from a problem. On some occasions, all other nodes get banned if a node

Hi all We did some failover/failback tests on 2 nodes��A and B�� with architecture 'glusterfs + ctdb(public address) + nfs-ganesha'�� 1st: During write, unplug the network cable of serving node A ->NFS Client took a few seconds to recover to conitinue writing. After some minutes, plug the network cable of serving node A ->NFS Client also took a few seconds to recover

centOs5.5/samba4/named here is a short guide setting it up to work. I added TSIG for bind-master amd bind-slave. Update to samba4 alpha13 added (installing git on CentOs 5.5). If you do this howto right now you will start with samba4 alpha13. You do not need the update section. But you need git for your installation because the rsync-thing is broken!!!!!! First of all do not install the bind

On Thu, 16 Feb 2023 17:30:37 +0000, Ulrich Sibiller <ulrich.sibiller at atos.net> wrote: > Martin Schwenke schrieb am 15.02.2023 23:23: > > OK, this part looks kind-of good. It would be interesting to know how > > long the entire failover process is taking. > > What exactly would you define as the begin and end of the failover? From "Takeover run

centOs5.5/samba4/named here is a short guide setting it up to work. First of all do not install the bind package coming with centos 5.5!! Install needs for samba yum install libacl* gnutls* readline* python* gdb* autoconf* Named installation: Here is a description on what to do: http://jason.roysdon.net/2009/10/16/building-bind-9-6-on-rhel5-centos5-for-d nssec-nsec3-support/ The steps, yum

CTDB Samba Team, I have a two-node cluster successfully running a GFS2 filesystem. I compiled ctdb ver 1.12 with Samba 3.6.3 for 64-bit systems. Running on RHEL 5.7. I was able to add the cluster to the domain but after I restarted CTDB, it panics right after doing a vacuum of the serverid.tdb database. The lock file is on the GFS FS so both nodes can access it. Any ideas as to what