similar to: poor performance with bonding in round-robin mode (only samba affected)

Hi! Some vnc clients has '-via ssh_gateway' option to simplify the setup of ssh port forwarding. Basically the option implements the following 3 steps: 1. Find local port available for listening. 2. Fork/exec ssh -L found_port:vnc_host:vnc_port ssh_gateway sleep some_delay 3. Connect to the found_port Although convenient the setup has its problems. First, it exposes the remote vnc

Hi, I''m trying to increase the bandwidth between two hosts (backup). Both hosts are in the same /24 subnet and each of them is connected to a Cisco switch by 2 GbE interfaces (intel e1000). The switches/host are located in different building which are connected by 3 x GbE. building A | building B | --------

(The list appears to have eaten my previous attempt to send this. Apologies if you receive multiple copies.) The attached patches allow you to use paravirtualised network and block interfaces from fully virtualised domains, based on Intel''s patches from a few months ago. These are significantly faster than the equivalent ioemu devices, sometimes by more than an order of magnitude.

Hi, I'm trying to configure ssh to get this behaviour: ssh binds on "localhost:60110" and when a local application connect to that port, all the data are forwarded to the "server". The particular fact is that I can't use port forwarding because I don't have any pop3 daemon on the "server". In fact I'm using a pop3 script as user's shell! $

On Wed, Jun 11, 2014 at 01:00:16PM +0530, abhishek jain wrote: > Hi RIch > > Below are the logs updated logs of libguestfs-test-tool on ubuntu powerpc... > > libguestfs-test-tool > ************************************************************ > * IMPORTANT NOTICE > * > * When reporting bugs, include the COMPLETE, UNEDITED >

Hello, I'm using virt-sparsify on a new server and I get an error message: # virt-sparsify img img2 [   0.0] Create overlay file in /tmp to protect source disk [   0.1] Examine source disk virt-sparsify: error: libguestfs error: guestfs_launch failed. This usually means the libguestfs appliance failed to start or crashed. Here is libguestfs-test-tool output:

Hallo. In our dovecot 1.2.6 server running under Solaris 9 I would like to set up a second quota root because the mail folders are in the users home directories and the inboxes of all users are in /var/mail. As soon as I add quota2 = fs:INBOX:noenforcing:mount=/var/mail the imap client crashes repeatedly as soon as the user tries to open a mail folder. Thanks for any help. Dovecot Logfile:

Processing commands for control at bugs.debian.org: > severity 777787 serious Bug #777787 [src:autofs] autofs: ftbfs with GCC-5 Severity set to 'serious' from 'important' > severity 777871 serious Bug #777871 [src:geis] geis: ftbfs with GCC-5 Severity set to 'serious' from 'important' > severity 777912 serious Bug #777912 [src:insighttoolkit]

After failing to get things to work on a Ubuntu 14.04 host I build a fedora 21 environment to see if Ubuntu may have been the problem and didn't get quite as far so here's an official report per the FAQ directions: - Trying to get guests to build and have network access so package management actions can be done before uploading to openstack image service. - I ran ./run virt-builder

Hi, how about to provide a simple way to forward raw file descriptors through ssh tunnels. something which may provide a way to write something like : (echo 3; read > out3) |& exec 3<&p 4>&p echo 5 >| out5 exec 5<> out5 echo 1 | ssh -d 3:rd -d 4:wr -d 5:rw ' read <&3; echo $REPLY >&4 read; echo $REPLY read <&5; echo $REPLY >&5

Processing commands for control at bugs.debian.org: > severity 777785 important Bug #777785 [src:attica] attica: ftbfs with GCC-5 Severity set to 'important' from 'normal' > severity 777787 important Bug #777787 [src:autofs] autofs: ftbfs with GCC-5 Severity set to 'important' from 'normal' > severity 777871 important Bug #777871 [src:geis] geis: ftbfs

Hi Rich I'm able to solve the problem regarding PAPR in libguestfs on my powerpc ubuntu.By default the libguestfs was configuring pseries machine and afterwards I changed it to my original machine i.e ppce500 .The changes are performed in ./src/guestfs-internal.h file. Thanks On Tue, Jun 10, 2014 at 7:58 PM, Richard W.M. Jones <rjones@redhat.com> wrote: > On Wed, Jun 04, 2014 at

Hi, I am currently running a 10 Node OCFS2 Cluster (version 1.3.9-0ubuntu1) on Ubuntu Server 8.04 x86_64. Linux n1 2.6.24-24-server #1 SMP Tue Jul 7 19:39:36 UTC 2009 x86_64 GNU/Linux The Cluster is connected to a 1Tera iSCSI Device presented by an IBM 3300 Storage System, running over a 1Gig Network. Mounted on all nodes: /dev/sdc1 on /cfs1 type ocfs2