similar to: Samba with 2 subnet browsing

Hi, I've just joined the list because of questionnaire in the forum [1]. The hardware is AMD-V(IOMMU) capable and is enabled in the BIOS with 3 NICs. I currently have host Windows 2008 R2 installed but binds (network services and protocols) on NIC3 only. My guests on VMWare workstation (has bridged network service bound on all 3 NIC) has bridged 3 NICs for the guests where NIC1 is WAN, NIC2

Hi, I'm not sure what sort of diagram you mean, but I'll have a try. Does this help? It sounds like I need to do something to enable routing on what I've labelled "NIC3" on the diagram - can you please explain what I need to do? [image: Inline image 1] Regards, Phill On Tue, Sep 1, 2015 at 4:53 PM, Ajey Gore <ajeygore@gmail.com> wrote: > Can you please drop a

Hi Ajey, I thought I already was doing bridge mode. Below are the network interface definitions from the XML config file for the Sophos VM. (Note that it's actually the middle definition which is connected to the cable modem which is different to how I showed it in the earlier diagram). What I don't understand is that the interface type says "direct" in the XML even though in

does you cable modem give you automatically the IP address? if thats the case then you need to do bridge configuration between nic3 and macvtap dhcp ip and then you will be able to get dhcp attached IP to sophos vm - ajey On Tue, Sep 1, 2015 at 4:33 PM, Phill Edwards <philledwards@gmail.com> wrote: > Hi, I'm not sure what sort of diagram you mean, but I'll have a try. Does

Hi Phil, But you said you disabled firewalld which makes me wonder if you have the necessary forwarding rules active. Dan On 1 September 2015 at 13:48, Phill Edwards <philledwards@gmail.com> wrote: > Hi Ajey, I thought I already was doing bridge mode. Below are the network > interface definitions from the XML config file for the Sophos VM. (Note > that it's actually the

Greetings everyone, I've been working on a (yet another) "all-in-one" Asterisk based project. It is aimed at embedded / low power systems (but scales fine on more capable hardware) and is based on Asterisk 1.4.x and FreeBSD 6.2. Because of this, I've mostly been hanging out on the asterisk-bsd list as bugs rolled in and the system's features were improved. We're

From: Christopher Snow <cs at m0n0.co.uk> > If that's the case, shouldn't the credit vote go to Fedora? Disclaimer: This is 100% my _opinion_ (don't take it otherwise) 1. Credit At some point a lot of credit can go to a lot of projects. Yes, many are thanx to Red Hat -- by far the largest of any commercial entity. But then many are thanx to many maintainers in general.

I have a T400P in my main building M and am going to put asterisk boxes in two buildings A & B. I already have our wan on fiber running between the buildings (including some extra strands) and the distance is beyond straight Ti distance so I would need csu... to use copper. It occurred to me that I could use TDMoE - and it may be less costly. My assumption is that the best to avoid the

Greetings list, Thanks to all who replied to my thread a few days ago "SIP devices with packet loss tolerance". One of the suggestions that came out of that thread was to replace routers at users' premises with ones that support QoS. I've used m0n0wall's QoS in the past with reasonable success, but it's quite a bulky and complex setup for deploying to remote sites which

I'm pretty new to KVM and have a KVM CentOS 7.1 hypervisor running a few VMs. I'm moving all my VMs from an ESXi host as I want to use KVM in future. Most of my VMs are working except for one which is running a Sophos UTM router (Sophos UTM is similar to products like pfSense <https://www.pfsense.org/>, Smoothwall <http://www.smoothwall.org/> etc). The host has 3 physical NICs

Hi guys, I'm new to LLVM and trying demo with the following C code: int main() { int a = 65535; *(1+(char *)a) = 0; return a; } unfortunately it generates the wrong IR: define i32 @main() nounwind { entry: store i8 0, i8* inttoptr (i64 65536 to i8*), align 65536 ret i32 65535 } seems SSA not applied on memory but incorrectly 'acrossed' by scalar values. Is it a bug?

Specifically what I am asking is, if I have a computer named ralph$ who is uidNumber 678 in ou=Computers and I have a user who is uidNumber 678 in ou=People, will this cause problems? Must the different sets of uidNumbers be disjoint acrossed different ou's?

In the course of correcting directory references for Mandrake in smbldap-tools I came acrossed the following: samba-2.2.7a/examples/LDAP/ldapsync.pl on line 72 we have: > $ntpwd = `/usr/local/sbin/smbencrypt '$oldpass'`; On Mandrake this would be: > $ntpwd = `/usr/sbin/smbencrypt '$oldpass'`; Except that I can't find anything by that name (i.e.

I love it... I buy a half a million dollars worth of Trashiba's finest ... I download Asterisk for free... I now refer to it as legacy 18 months and 300 extensions later! Anyway, I am trying to integrate my dial plans acrossed platforms. PSTN>>>CTX670>>>Asterisk The dialplan I would like to setup, 1xx,2xx,3xx,7xxx to the CTX 670 4xx,6xxx to a remote ctx100 (this is setup

I have been reading the README for icecast beta 4 and I came acrossed a line that isn''t very explicit can some one explain to me what needs to happen here? You WILL need to edit the config file you choose to use before running this application. When documentation is revised tthis may be a good thing to be a little more explicit on. --- >8 ---- List archives:

I have read the documentation, performed the diagnostic tests, checked the archives, so if the answer is there, please accept my apologies in advance and simply direct me. I am running redhat Linux 2.0.3 and using smbmount to mount several directories from NT3.51 servers which are distributed gloablly in different timezones. Once mounted the files all have local timestamps which makes syncing

This has to be the worst documentation I have ever come acrossed. I have found two or three docs on how to install it, but they are all so different and make huge assumption about what packages you have installed and locations of files. Has anyone seen something better, I want to get this working it is quite a cool app. Jordan Novak Communications Technician Logistics Health Inc. 1319 Saint

I tried netperf / netserver with Dom0 / DomU, but I could''nt get a correct NW traffic with xentop. Is there anybody could help me? At Host1''s Dom0, run netperf -H VMIP At Host2''s DomU (with VMIP named TTVM), run netserver At Host1, run xentop this way ->"xentop -n -b -d 1" At Host2, run xentop this way->"xentop -n -b -d 1" In Host2''s