similar to: conflict between Realtek 8139 (client) and 3c2000T (server) NIC's with Samba? - solved

Hi, Last friday I changed the NIC in two of our Samba servers from a 3com 905b (100mb) to a 3com 2000T (1000mb) to take advantage of our new switch which supports gigabit. One of the workstations (XP SP1, with all subsequent patches and hotfixes and with an onboard Realtek 8139) then started to have problems with the two Samba servers with the new NIC's. It could see the network

Completely agree. I used to have 8139c cards in my home machines, on a switched 100mbit network, including a Dual P3 server that I run 4 x 80G drives with a HPT454 RAID5 array (software I know, but the dual P3 copes admirably), both the server and my main desktop (dual Athlon MP 2600) were getting to the point of being unusable when such high CPU useage when transferring large documents (Quark

Hi there, slightly off-topic, but probably of interest on this list. In the meantime there are freely available PXE Bootroms for lots of cards. I'm aware of Intel, 3com and Realtek based cards. I'm still looking for a PXE-Bootrom for Tulip based Cards though! Would be nice to have a List of some sort on the PXElinux homepage. So here is one Link I'm aware of:

Hallo, rid, Du meintest am 13.06.13: > hi, realtek 8139 \ 8100sc NICs can not be used PXELINUX 5.0 -> > 6.0-pre4 version boot, please verify. tested with 6.0-pre4 and an "etherboot" disk for realtek-8139: no problem. Viele Gruesse! Helmut

I found (and fixed) a problem with my realtek onboard 8139 controller. dhcpd server sends filename "pxelinux.0" but realtek requests "pxelinux.0\377" (i.e. the octal character 377 is appended), resulting in a file not found during the tftpd phase. I fixed this by adding a mapping to tftpd: # strip ending garbage from filenames (Realtek PXE bug) r ^([[:graph:]]*)(.+)$ \1

Hi all, I swapped a Realtek 8139 100M Net Card for a Realtek 8169 Gig Net card in a Centos 5.6 system. After reconfiguring the network settings I find that on boot up the 8169 interface does not start. The startup script says something like "The 8169 is not available..." ifconfig -a shows a device with the right mac address called __tmpsomethingorother I can get it going if I

Jerry Geis <geisj at pagestation.com <http://lists.centos.org/mailman/listinfo/centos>> wrote: >/ Hi, />/ I have a compaq V2000 laptop. Specs for network say its a />/ realtek 8139/8139C+ NIC. / Is it really a RTL8139? Or it is possible that it's a RTL8100? The reason I ask is because while the RTL8100 is supposed to be MAC compatible with the RTL8139, I'm finding

I''m trying to build out a test cloud using XCP 1.0.0 beta with 3 machines of 18 cores total (Phenom II 1090s). I''ve built three machines, installed XCP 1.0.0 beta on them and they all three have the same problem - the Realtek network cards don''t work. The following is the output from lspci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI

Hi all, Our intranet's WAN interface just stopped working yesterday, and I can't figure it out. The machine has a Gigabyte motherboard, with on-board RTL-8110SC/8169SC Gigabit Ethernet and D-Link PCI NIC for the LAN side. I can get into the LAN side without an issue, but can't see the WAN side at all. [root at intranet ~]# ifconfig eth0 up eth0: unknown interface: No such device

I was trying to do some performance testing between using iSCSI on the host as a diskfile to a guest vs the VM guest using the iSCSI device directly. However, in the process of trying to establish a baseline performance figure, I started increasing the MTU settings on the PCI-express NICs with RTL8168B chips. First bottleneck was discovering the max MTU allowed on these is 7K instead of 9K but

I have an Asus P5Q-WS running FreeBSD 7 and the onboard Realtek NIC's are not being detected. No Kernel modifications as this is a fresh install. pciconf -lv : re0@pci0:3:0:0: class=0x020000 card=0x82c61043 chip=0x816810ec rev=0x02 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' class = network

Realtek is "real" good about getting drivers for their chips into the kernels as soon as possible. They are one of the few vendors that I have never had a problem with built in support... Mike McCarthy On 06/03/2016 08:03 AM, Phil Manuel wrote: > You can get the Linux driver from >

ok thanks for your answer so quickly !! Cheers Rémi ----- Original Message ----- From: "James Harper" <james.harper@bendigoit.com.au> To: "Rémi BERNIER" <R.BERNIER@grelier.com>; <xen-users@lists.xensource.com> Sent: Thursday, October 29, 2009 9:49 AM Subject: RE: [Xen-users] How to hide Realtek card with GPLPV 0.10.0.130 > > Hi everyone, >

You can get the Linux driver from http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=5&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false#RTL8111B/RTL8168B/RTL8111/RTL8168%3Cbr%3ERTL8111C/RTL8111CP/RTL8111D%28L%29%3Cbr%3ERTL8168C/RTL8111DP if you can't find it under C7 Regards On Fri, Jun 3, 2016 at 8:11 PM, Alessandro Baggi <alessandro.baggi at

Greetings- I'm attempting to get CentOS 5.5 x86 (yes, very specific version required for specific software usage scenario... don't ask) running on an Intel D425KT mini-ITX motherboard. Everything works fine, with the exception of the onboard ethernet, which is a Realtek RTL8105E chip. The stock CentOS installation attempts to use the r8169 driver, which does not work. I've been around

Hi list, I'm planning to buy a mobo (z170-K) that has Realtek 8111GR (nic). I've tried to search on google about support on C7 but can't fine anything. There is a way to check if supported? Is the Realtek 8111GR supported or I must change mobo? Thanks in advance.

Hi, I try to make my SD-reader work on a HP ZBook. lspci 5d:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5249 (rev 01) uname -a Linux Antisana.psc-elsene.be 2.6.32-431.17.1.el6.x86_64 #1 SMP Wed May 7 23:32:49 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux Googling gave me http://linuxterminal.org/issue-with-rts5229-pci-express-card-reader/; last reply by Fran?ois suggests to

Hello, We can see # lspci 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) I have used a custom kernel to start with centos 5.1 as an initial installation Our customer on this kernel has experienced slow pref on samba shares (50 seconds to open a file) So I have decided to updrade to centos 5.2 that have the right

While installing Centos 5.0 x86-64 on a Gigabyte GA-945GM-S2 motherboard which has Realtek 8111B Ethernet chip - Anaconda crashes. I select the option to use the Centos online repository for extra packages - I am asked to enter IP address etc. The drop box to select the Ethernet interface is blank. If I enter valid IP address and gateway - anaconda crashes and the system reboots from CD. I

I just installed Centos 5.5 x86_64 on a new Toshiba Satellite L1500D. Everything seems to work (so far) other than the wireless networking; lscpi tells me: 0e:00.0 Network controller: Realtek Semiconductor Co., Ltd. Unknown device 8172 (rev 10) I discovered that I need the realtek driver, so I found and downloaded these: rtl8192se_linux_2.6.0010.1012.2009_64bit.tar.gz