similar to: Linux+samba problems

Just an FYI, I noticed some people not being able to use the CLI of their adit 600's because of a set password. You can erase the configuration of the adit 600 by setting the RST dip switch to on, powercycling the box, waiting until it finishes coming up, setting it back to off, and powercycling again. -Joe

Is there a Samba utility to control NT Services or does anyone know of a way to remotely restart NT services from a linux box ? I realize this may not be a Samba question but I felt this was a good place to start. Thanks in advance for any ideas !!! Josh

hi all, i just inherit a server: Compaq ProLiant ML370 Generation 2 Server with Smart Array 5300 Controller with 6x18.2GB hard drives. i want to install centos 5 on it with hardware raid 1. any idea how? it also has a build-in and add-on ethernet cards. how do i know which one is which to assign ip? thanks. t. hiep

Hello all Here is the scenario: We have a mail server VM which currently has two virtual NICs attached to it. One NIC is has an IP on a subnet with a default gateway defined and the other NIC has an IP on a different subnet with a different gateway on a different VLAN defined. Now when I activate both NICs, and run an ifconfig -a, I see that both IP addresses are showing. Now here is the

Dear Sirs. I have a ML370 G4 server with 2 disk SCSI Ultra 320 of 300 GB in RAID-1 through a controller and operating system CentOS 4.7. My question: CentOS 4.7 could support the expansion of capacity by adding 6 disks SCSI Ultra 320 of 300GB in Raid-1? Thanks for your reply Luis _________________________________________________________________ News, entertainment and everything you

Hello, I'm trying to set up IP aliases within a QEMU/KVM guest on CentOS 5.5 x86_64, going through a bridged virtualized interface. The virtualized interface in the guest is configured as follow: # ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none PEERDNS=yes GATEWAY=IP.OF.HOST.GATEWAY HWADDR=11:11:11:11:11:11 IPADDR=IP.OF.GUEST.ETH1 NETMASK=255.255.255.255 ONBOOT=yes ARP=yes USERCTL=no IPV6INIT=no #

Dear Sirs I have a ML370 G4 server with 1 CPU Intel (R) Xeon (TM) 3.60GHz and 2GB of RAM with operating system CentOS 4.7 and kernel 2.6.9-78.0.22.ELsmp We have acquired 1 CPU and 2 GB of RAM additional to improve the functioning of the server, my question is whether the current kernel can support the addition of hardware or if I need a new kernel or install any additional software. Thanks

Dear all. I am trying to buy a hp server to run R and to complete some other tasks with limited bugets. The r-project.org site recommended that R will run on hppa-hp-hpux. However this system is out of our buget and ML system from hp is much cheaper. Is there anybody running R on ML370 or ML 570 systems? If you can provide me with some other information related that will be appreciated.

Hi all, I have somewhat a strange problem that I could not figure out, maybe someone here can lelp. I have a script that uses scp to distribute files to many servers, I use '-o BatchMode=yes -o ConnectTimeout=2 options so the scp will not get stuck if something is wrong with the remote host. If the remote host is down (non-pingable) or sshd is down the timeout option works and the scp

Hello, all I apologize for all these questions. But I have so many running through my head for this. What brand of server is a good one to use for running an asterisk box? I did an install the other day on a Compaq Proliant ML370 G2 / Debian Sarge and it is currently working great. But HP/Compaq costs bukooo bucks. I have heard Super Micro is what alot of you are using. Any problem running

I know that this is not a pxelinux/syslinux question (yet), but I am having a weird issue with a HP ML370. It is using HP UNDI PXE 2.1 (build 082) v 3.1.15 I successfully get an IP address from my DHCP server, but the machine fails when it attempts to make it's TFTP connection with: "PXE-E32 - TFTP Open timeout" It never gets the pxelinux.0 file. The odd thing I noticed was

My local centos mirror (ftp.crc.dk) failed to boot after having upgraded from centos 5.0 to 5.1 (i386). It just displays GRUB The cursor is positioned to the right of a space after GRUB, and no input is accepted. I've tried booting in rescue mode and run: chroot /mnt/sysimage grub-install /dev/cciss/c0d0 This completes without errors, but still it can't boot. It's a HP/Compaq

Hi, I'd like to install centos 5 on a HP proliant ml370 server with a xeon cpu, is it ok the install-dvd for x86_64 architecture ? The server will be a samba server plus virtualization. -- Email.it, the professional e-mail, gratis per te: http://www.email.it/f Sponsor: In REGALO 'All the Good Thing' di NELLY FURTADO Clicca qui:

Hello people I currently have a ML370 G4 server with a CPU in centos 4.7, this server has the ability to add another CPU. the question is, Centos can recognize the second CPU? and if so, is there any special configuration to be performed. A forward to your comments Greetings _________________________________________________________________ News, entertainment and everything you care

hello I have an asterisk server with a te110p E1 digium card. the server is a hp ML370 3,2 Ghz 64bits, 1Mo L2 , 1Go Ram, 3 SCSI 73Go in raid5. I want to use in the same machine the kannel SMSC. i have no big trafic in the two gateway but I want to know if it generate a performence problem for asterisk I use fedora core4 with latest asterisk version . thanks Regards issam -------------- next part

Hi all, Read many posts on the subject. Using 802.3ad. Few problems; Cannot ping some hosts on the network, they are all up. Cannot resolve via DNS which is one of the hosts that I cannot ping, internal nor external DNS hosts. Unplugging the NICS and plugging them back in will then not allow pining if the default d=gateway. When cold booting it somewhat works, some hosts are pingable while

I am having issues with guest OSes running on SLES10 (Sun 4200) hosts. Periodically, the guest OS system drops off the network. From the general network it is not pingable, consequently, ssh fails. If however, I log into the SLES10 server that is hosting the guest OS and ssh to the guest OS, then it becomes immediately pingable and accessible to the rest of the network. Almost like the

Hello, Freebsd-stable. I installed 7.1-STABLE on my new Soekris net5501. Kernel config is in attach. This unit lock up in strange way every day. It is pingable, but no access to host on any network protocol (sshd, named, etc are not answering), and serial console (only one this unit has) DOESN'T ANSWER too! Only way to un-freeze it is cold reboot. I've thought, it is

Ok, I''m hoping this is a fairly trivial issue, and I''m missing something. I''m trying to use Solaris zones (Nevada Build 117) to act as a DMZ and a router, using exclusive IPs, VNICs (from Crossbow), and connecting to the internet (static IP from my ISP). I''ve got the DMZ working - that zone sees the internet, can do name lookups, ftp, telnet, ssh, etc etc etc.

Hello Rsync PRO?s, i?m satisfied with the rsync features...never seen a better replication tool....!! ;-) But i have some problems...:-( OK, here me installation: - one Compac Proliant ML370 with cached SCSI HDDs and 1,2GHz and 1gb RAM... on this machine we have the Rsync deamon runnig to export the data we want to replicate - now we have 68 other NAS machines in our branch offices and this NAS