similar to: mke2fs incorrectly detects partition size

Hi folks, For unknown cause I encounter following mounting problem; # /mnt/hda8 mount: wrong fs type, bad option, bad superblock on /dev/hda8, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so # dmesg | tail via82cxxx: timeout while reading AC97 codec (0x9A0000) via82cxxx: timeout while reading AC97 codec (0x9A0000)

Hello, I am trying to boot an RHAS 4 release 3 guest kernel (the binary release available through Redhat Network) from a SLES 10 dom0 host (the binary release available through Suse''s software distribution channel). Both systems are installed as physical partitions in a standard multiboot configuration on a single hard drive on a recent vintage HP Pavilion (zd7380) notebook PC with a

Hi, I've been foolish enough to let Partition-Magic move/resize/etc. my partitions without a prior backup. My ext3 /dev/hda7 (was RH 9) is no longer recognised by fsck. I tried fsck -b 8139, 32768 and 65536 - but am not quite sure about if these are the right ones to try. So far I created another partition with same number of blocks and did a backup with dd if=/dev/hda7 of=/dev/hda8

Suse 10.1 AMD64 Xen3 New to Xen. The dom0 is up and running. I am trying to get my first domU working. My approach is to use precompiled images from jailtime.org. After some manual tinkering with the .cfg file the domU proceeds to boot but stalls with the following error. I cannot get past this - any ideas ? Brian Using config file "/etc/xen/vm/vm1". Started domain vm1 Bootdata ok

Hi, "Mircea Popescu" <nufarul.alb at go.ro> schrieb am 29.01.02: > I have this problem: > I've partitioned my hard drive with PQMagic 7 in the following way: > hda1 - fat32 > hda2 - ext2 > hda3 - fat16 > hda4 - extended > hda5 - Linux Swap > hda6 - fat32 > hda7 - ext2 > hda8 - fat32 > > I've put syslinux on

Good morning, I try to use the last release of ext3 patch with a 2.4.10 linux kernel. I have two troubles : - when the kernel is booting, I receive : NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 208k freed Adding Swap: 128480k swap-space (priority -1) Adding Swap: 128480k swap-space (priority -2) Why my root

> [6] ctivating swap partitions: swapon: /dev/hda7: No such device or address > [6] [FAILED] > [6] ioctl 80041272 not supported by xl_block > [6] Finding module dependencies: depmod: Can''t open /lib/modules/2.4.24-xeno/modules.dep for writing > [6] [FAILED] > [6] Checking filesystems > [6] Couldn''t find matching filesystem: LABEL=/policy Edit your

I am trying to use data=journal on my root file system. I have separate slices on which journal=data works fine on all of them, except root. I have tried putting rootflags=journal=data on my kernel line in Grub, but I get a kernel panic. I'm missing something simple, I jut know it. It can't be the kernel version because it works on the other slices. My etc/fstab file is as follows:

I thought I've found three bugs on syslinux 6.03: (1) With sample config file as is, i.e. leaving commented MENU VSHIFT and MENU COLOR UNSEL but uncommented MENU COLOR SEL: A black "border" is displayed below the selected line and on its right edge. (2) Uncommenting MENU COLOR UNSEL: This effect appears also on separators and on right edge on every unselected lines. (3)

Add a couple of documentation details about PV-GRUB support - the menu.lst content can be passed as a ramdisk. - virtual partitions are not supported. Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> diff -r b8d2a4134a68 stubdom/README --- a/stubdom/README Wed Mar 03 17:41:58 2010 +0000 +++ b/stubdom/README Wed Mar 03 20:42:53 2010 +0100 @@ -52,11 +52,17 @@ extra =

Hello, unfortunately I got some trouble using ext3 - the system hangs when working in a certain directory. Not completely, I can switch between consoles and reboot with SysRQ, but cannot do anything which requires disk IO: not start any applications, not umount, nothing. I could send the strace output, but I don't think this would help anyone. Sorry, but I don't have a clue where to start

I've posted here with this problem before, and while several people DID try to help, nothing seems to work! Here's the situation (again): I have a Linux box (Mandrake 7.0) running Samba (2.0.6) compiled from source. I can mount/read/write the linux shares just fine, but when trying to write to my Win98 shares (which mount perfectly), I get "permission denied". This only

Hi, Updated to current bk today, and my machine stopped booting ... I''ve tracked it down to the apic changes from end of last week. cset 1.1307 boots fine, 1.1308 doesn''t. Diff of the boot messages is below. Full logs are also attached. Gerd --- log-1.1307 2005-04-21 14:40:57.372885027 +0200 +++ log-1.1308 2005-04-21 14:38:52.236553392 +0200 @@ -7,7 +7,7 @@

Hi, Just got Fedora FC1 vanilla 2.4.25kernel+libata8patch booting problems, FC1 complains that it can not automatically find&found partitions specified with "LABEL=" in /etc/fstab, and then falls me into repair mode. In the repair mode I can mount it manually without any problems. More interesting are: 1) I have several partitions specified with "LABEL=*" in

I doubt that this is actually an ext3 problem so I'm taking a bit of a liberty, but... We have several machines that have two ext3 partitions (/, /boot) and a large raw partition. Something happened that destroyed both the ext3 partitions on all machines. I appears that the app writing to the raw partition had a bug that caused it to write to negative block numbers and that this wrote all

hi all, i have reinstalled linux i kept free 17 gb space. i have created 4gb partition by fdisk with LVM options. fdisk -l Disk /dev/sda: 40.0 GB, 40060403712 bytes 255 heads, 63 sectors/track, 4870 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 1275 10241406 7

hi all, i have reinstalled linux i kept free 17 gb space. i have created 4gb partition by fdisk with LVM options. fdisk -l Disk /dev/sda: 40.0 GB, 40060403712 bytes 255 heads, 63 sectors/track, 4870 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 1275 10241406 7

Hello, What am I missing ? thanks ! -dikshie- @fisbum:/usr/bin$ uname -a Linux fisbum 2.4.18 #3 Tue Mar 19 16:55:23 JAVT 2002 i686 unknown @fisbum:/usr/bin$ mount /dev/hda1 on / type ext3 (rw,errors=remount-ro) /dev/hda3 on /usr type reiserfs (rw) /dev/hda5 on /home type reiserfs (rw,nosuid,usrquota) /dev/hda6 on /var type reiserfs (rw,usrquota) /dev/hda7 on /tmp type reiserfs (rw) /dev/hdb1

Hi. I need to use the ntlm_auth module to auth. users so a group can use Internet and other not, using squid. The users that belong to "Internet" group may use Internet. I've being looking for info. about this but there is no much info. in google. Until now this is the only info. that I had found: for squid.conf: auth_param ntlm program /usr/bin/ntlm_auth

Please help me understand why I am unable to connect to and browse the newly configured DFS tree that I installed on my Samba server according to the instructions found in Chapter 18. "Hosting a Microsoft Distributed File System Tree" of the official how-to. Irrespective of whether I try to access the dfs file tree from either the local file browser (and choosing the SMB tree) or from