similar to: Summary of hangind HP proliant

Hello. Recently I've ran into problems with HP Proliant booting off the network with menu.c32. Configuration -- several identical servers: HP Proliant DL360 G5 HP Bios P58 12/26/2006 Bootblock 09/18/2006 HP SmartArray E200i Controller (128MB, v1.20) Broadcom NetXtreme II Ethernet Boot Agent v2.8.5 When localboot is chosen from menu.c32 menu I get standard "PXE-M0F Exiting ...",

Hello. I'm looking for assistance or pointers for the following problem. OS: RHAS2.1 enterprise16 HW: HP proliant 2CPU 6GB RAM, internal RAID1 + RAID5(4 x 10K 72GB) When we run any kind of process (especially tar for some reason) that creates heavy disk activity the machine becomes Very Slow, (e.g. takes 30-45 seconds to get a reply from ls at the console, or a minute to log in.) I

I'm looking at ordering a server from HP. I checked around on Google and found in the Wiki that the ProLiant DL380 is supposed to be known to work with *. I'm going to get a price quote on the following setup: HP ProLiant DL380 G4 Server w/ the following options: Intel Xeon 3.20GHz/1MB 2GB REG PC2-3200 (2 X 1GB) HP ProLiant Battery Backed Write Cache Enabler for SA6i RAID 1 drive set HP

Hello, I've been having a problem trying to boot from first hard drive via pxelinux 5.01 on a HP Proliant server having a SmartArray P220i RAID controller. On other hardware and VMs that i've tried it works. My config file looks like this: label localboot kernel chain.c32 append hd0 Is this a known issue or has anyone experienced this? Thanks, Andrei

will C5.3 support a SmartArray 6i 'out of box', or does it need drivers to boot from this? I am advising someone else remotely and don't have the hardware handy to test.

All, I would like to run the following issue past the list to confirm that my problem analysis makes sense or whether I missed something: We have a HP ML370G6 server with VT-x and VT-d enabled in the BIOS. It is equipped with two Smart Array HBAs - one connected to the HDD array (SmartArray P800) and one connected to an LTO tape drive (SmartArray P212). Both controllers use the same driver

How I can set up CentOS 5 on it if it don't see the drives. -- Juan Pablo De Mola Rodr?guez

First issue: I did an upgrade from 4.7 to 5.3 on an HP DL380G3 box. I got yum working again and upgraded 160+ packages. During that process I saw: ------------------------------------------- Installing : kernel-PAE [157/322] WARNING: No module mptscsi found for kernel 2.6.18-128.2.1.el5PAE, continuing anyway Installing : kernel [158/322] WARNING:

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

I have CentOS 6.x installed on a "HP ProLiant DL380 G5" server. It has eight 750GB drives in a hardware RAID6 array. Its acting as a host for a number of OpenVZ containers. Seems like every time I reboot this server which is not very often it sits for hours running a disk check or something on boot. The server is located 200+ miles away so its not very convenient to look at. Is

My local centos mirror (ftp.crc.dk) failed to boot after having upgraded from centos 5.0 to 5.1 (i386). It just displays GRUB The cursor is positioned to the right of a space after GRUB, and no input is accepted. I've tried booting in rescue mode and run: chroot /mnt/sysimage grub-install /dev/cciss/c0d0 This completes without errors, but still it can't boot. It's a HP/Compaq

Hi all, I discovered lately that two of my XEN servers suffer from a really bad disk throughput - in domU as well as in dom0. All of them run Debian/Etch, Kernel 2.6.18-6-xen (orig. Debian) with XEN 3.2 (backported). The software versions seem to be ok for most machines: Lenovo A57 with S-ATA and (E8200, VT enabled): up to 90MB/s Shuttle, FB61 based, ATA-Disk (Celeron, no VT): up to

Hi, I have setup an old Compaq Proliant DL580 with 2 xeon @700MHz 2Gb RAM two SmartArray 5300 controllers and 12 drives in an array enclosure. I am running the latest opensolaris update bfu''ed from binaries since I could not build from source. I am controlling the drives with the cpqary3 driver (Solaris 10) from HP. Initially the array had 7 drives and I created a raidz zfs pool

I had to install C5 on a dev server for various reasons (legacy system support and so forth). This dev server is a HP DL180 G6, with a SmartArray P410 raid card... I've installed hpacucli via the RPM from HP's site, but its not finding the controller... C5 (64 bit) is using the default CCISS drivers for this card. # hpacucli ctrl all show config Error: No controllers detected.

On 10/7/2015 11:47 AM, Jack Bailey wrote: > On 10/07/15 11:13, m.roth at 5-cent.us wrote: >> Jack Bailey wrote: >> >>>> controller that expects to talk to individual SAS or SATA drives. you >>>> can manage it with hpssacli from centos. >>> I have the P822. It has no JBOD or RAID 0. hpacucli works with CentOS >>> 7.0, but is broken on 7.1

> What I've done in the past is before the nightly backup write a small > file to the root of each filesystem giving disk geometries.? You can > then use any recovery DVD to partition and reload the OS.? If rear can > do this for me it would be __much__ neater! According to rear webpage: https://relax-and-recover.org/about/ Extensive disk layout implementation, incl. * HWRAID

I've included all posts till now. Can I ask anyone with older proliant multi-cpu hardware using the smart2 controllers to get in touch with me? I am curious to know if this works for anyone... -D Quoting Danny Carroll <fbsd@dannysplace.net>: > Still more info... > It does not work on 5_0-RELEASE either. > > -D > ----- Original Message ----- > From: "Danny

I've got two DL385s and a DL320, and they all rock. iLO especially rocks, but to leverage the full functionality, you'll need to get the "Advanced License", which opens up full blown remote console capabilities (via Java). It's a separate piece of hardware that, as long as the server PSUs have power flowing into them, lets you do things like remotely power on/off/reset the

23.09.2011 11:31, Janne Pikkarainen ?????: Thank you for reply, BTW, other webserver has almost the same bonnie results (10283ms and 5884ms) on ext3 partition with 45GB of data (1.5 millions of files)?! Hardware and RAID5(also hardware) are the same: HP Proliant DL380 G4 with SmartArray 6i controller (as I see it comes with 128MB BBWC enabler but not kit). I did not tried to mount fs with

Hello, Has anyone out there been able to qualify the Proliant DL360 G7 for your Solaris/OI/Nexenta environments? Any pros/cons/gotchas (vs. previous generation HP servers) would be greatly appreciated. Thanks in advance! -Anh