similar to: Busy BLKFLSBUF on bootup

Hi, Since upgrading to 2.4.14 with the ext3 patch, I've been getting the following on bootup: VFS: Mounted root (ext3 filesystem) readonly. change_root: old root has d_count=5 Trying to unmount old root ... invalidate: busy buffer invalidate: busy buffer invalidate: busy buffer invalidate: busy buffer invalidate: busy buffer okay Is the invalidate busy buffer bit anything to worry about?

Hi, got a very severe problem. I have two hard drives in my RS server and I am getting the secondary drive removed. Here's the problem. After the secondary drive is removed, the server fails to bootup completely, crashing at fsck. The server boots up fine when the secondary drive is put back in however. Has anyone ever encountered this problem before? Could the problem be to references to

----- Message d'origine ---- > De : David Baron <d_baron at 012.net.il> > ? : wine-users at winehq.org > Envoy? le : Jeudi, 28 F?vrier 2008, 18h53mn 08s > Objet : Re: [Wine] How about this replacement of WINE. > > > However, it's a great, great project IMO. It was about time something > > > like that should've been made. Redirecting calls is simply

wine: Unhandled page fault on read access to 0x409ffd80 at address 0x4000ba7c (thread 0009), starting debugger... err:seh:start_debugger Couldn't start debugger ("winedbg --auto 8 32") (2) Read the Wine Developers Guide on how to set up winedbg or another debugger This happens on everything I try run. Note: Still a problem with latest upgrade. It may have more sideeffects than

Get this warning on bootup ext3 file checks on 2.6.* kernels. Apparently harmless, but how do I fix this? _______________________________________________ debian-knoppix mailing list debian-knoppix at linuxtag.org http://mailman.linuxtag.org/mailman/listinfo/debian-knoppix

Dear Xen Community, today we tried to upgrade our base server from a Xeon E5430 to a Xeon X5570 (Nehalem). This worked fine so far, but our DomUs with Kernel 2.6.27 no longer boot - they start up until the following message appears: [..] Mount-cache hash table entries: 256 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup

(There really doesn't seem to be a dedicated e2fsprogs list, so this was the next-best place I could find. I don't place much faith in the sourceforge forums..) The filesystem in question is a 480 gig ext3 partition, on a hardware RAID5 controller. It's approximately 90% full, with something like 115K files. Kernel 2.4.20-pre4, on a Duron 900. As I type this, e2fsck has used up

An HTML attachment was scrubbed... URL: <http://listman.redhat.com/archives/ext3-users/attachments/20060828/ce9c7bc0/attachment.htm>

It seems that fewer and fewer favorite programs run with wine. Stuff that ran 100% on older builds crashes out on the newer ones with elan. There needs to be (more) regression testing. However, damage has already been done and propagated and needs correction simply to get back to the previous level of operability.

Hi! We're using 2.4.15-pre5 on our Postfix mailserver. /etc/fstab: LABEL=/var /var auto data=journal 1 2 LABEL=/home /home auto exec,dev,nosuid,rw 1 2 Recently, we got the following entries in our /var/log/messages: Dec 1 00:42:05 postamt1 kernel: invalidate: busy buffer Dec 1 00:42:05 postamt1 last message repeated 329 times

Hi there: As suggested in the docs, I am forwarding a bug report. I have just converted two partitions to ext3 from ext2 without reformatting on my home box. All is not well, however. Here's the specs AMD K6/2-3D 500 Mhz, 64MB SDRAM, 100 Mhz bus Via Apollo P5MPV3 chipset, 100 Mhz bus Opti Mad 16 931 soundcard Video= AGP S3 Trio, w/8MB RAM, PS/2 mouse. Realtek 8029 pci bus network card.

I have 5 VMs on my host. The first four are setup to start on boot. But only the first three end up running. The fourth has to be started manually. "Start virtual machine on host bootup" is checked on all four VMs but the fourth VM does not get started on host bootup. After the host boots up, the VM is "Shutdown" state. If I go into "virt-manager" and click

CentOS 4.1, Xen 2.0.7. My dom0 is booting up but can''t get to the outside network because eth0 won''t start due to, apparently, Xen providing a different mac address than expected. How do I tell Xen to start eth0 at the bootup with a specific mac address that lines up with the HWADDR= line in my ifcfg-eth0? Note that a normal bootup into CentOS 4.1 outside of the Grub Xen bootup

I am running SUSE 12.0 I have had this problem on another machine months ago, but never solved it. I have done many searches, but have come up empty. When booted, port 139 is not open on IPv4. There os no 0.0.0.0:139listening. HOWEVER: :::139 is listening. SO I know it is open on IPv6. When I try to gain remote access through a share, the machine is not found. When I try to telnet to port

Hi, I was wondering if there is a variable in HVM configuration file to set the default vga display size for a windows guest? Or if anyone knows the location in the qemu or the cirrus vga bios code where I can make this change to set the default display size. Thank you for your help and time, -Yung _______________________________________________ Xen-users mailing list

<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"> <html> <head> </head> <body bgcolor="#ffffff" text="#000000"> <font size="-1"><font face="Helvetica, Arial, sans-serif">There is a rather complex procedure described in the FAQ for starting up the database server and web server&nbsp; on

Is there a way to disable the auto reboot when the kernel panics during bootup? I tried passing "panic=0" using grub but it still reboots automatically. I need to at least pause it long enough to read the screen to determine the cause of the panic. Thanks for any help.

Hi, ALL When I use "tap" config, the VM is OK. Than I replace disk config "tap" with "tap2", And VM hangs during bootup. I use "xm list" to list vm and find the time of hanged VM is growing fast. After VM hangs, we can not create other VMs. It prints "Error: Device 0 (vif) could not be connected. Hotplug scripts not working" . How can I fix it?

Hi all, Does anybody have an idea about this "ioremap error" during the booting stage of VM CentOS7, although it can eventually bootup successfully. Regards, Allen 2014-11-05 Allen Qiu

While rebooting my computer after installing the new kernel a few minutes ago, I got to wondering about how the initial bootup screen (after grub, before rhgb) is constructed. The "Loading kernel blah blah blah" lines start at the top of the screen and proceed to scroll down as one would expect. But "kernel alive" shows up at the bottom of the screen and then more write-up is