similar to: Partitioning for ext3fs

greetings. centos 6.7 [current] 'disk utility' has started showing message; WARNING: The partition is misaligned by 2560 bytes. This may result in very poor performance. Repartitioning is suggested. for sdc5 - /home partition. /dev/sdc5 302243312 156348604 130534968 55% /home /dev/sdc7 80854912 57088 76683952 1% /hdd/c/07 other than time involved to backup

Hi, I just bought a Seagate 1TB USB drive thinking that I could create a few partitions in it, format in ext3 fs, then configure bacula to setup a backup server in my CentOS box and backup my windows and mac clients. I have plugged the drive and mounted in /mnt/usbdrive and is seen as /dev/sdb1 by the OS. The output of df command is: [root at Production ~]# df Filesystem 1K-blocks

I need to install Centos on a machine with 3tb raid disk. (3 ware raid card) Could someone in the list suggest a utility for partition this disk. I would like to have the whole disk in 1 partition and format it for ext3. The default partitioning utility doesn't do this. The OS sits on another SATA disk and each time during the installation it doesn't format the full disk which is 3TB.

Hello, new Linux user here and I cannot mount a new (empty) WD MyBook Essentials 3TB USB external hard drive (Model WDBACW0030HBK-NESN). I'm only about 3 weeks into this linux thing and so please forgive me if any of my syntax is off My linux OS is CentOS 5.4 x86-64 running on a dedicated HP z400. The WD MyBook is to back up the large data files we are creating on the HP400 (it's

On 04/22/16 08:19, Leon Fauster wrote: <<>> > check it with: > > blockdev --getalignoff /dev/sd > > (if a '0' is returned, the partition is aligned) > ===> Leon, thank you for reply. ]$ sudo blockdev --getalignoff /dev/sdc1 0 ]$ sudo blockdev --getalignoff /dev/sdc2 0 ]$ sudo blockdev --getalignoff /dev/sdc5 2560 ]$ sudo blockdev --report /dev/sdc1 RO

Hello, I have a server working on centos 5.7-64 minimal installation. I have 3 separate physical drives: 120 gb ssd, 2x 3tb disks for storage. My linux installation is on ssd disk, and I want to make raid 1 for these two 3tb disks and store data, like under /mnt/data. Can you please tell me the path how this is possible? Thanks for your help! Best regards, Here are some output of commands I

Dear All I needed to clone my disk to another hard drive . I did it as the following : #dd if=/dev/sdb of=/dev/sdc But after a while, the procedure ended with the "writing to /dev/sdc input/output error" message. Can you please let me know how can I overcome this as the fdisk now returns as " #fdisk /dev/sdc "I do not know how to handle files with mode 81a4 must set

Hi all, Does anyone know if it's possible to recover an LVM partition from a drive that was fdisked? I accidently fdisk'd the wrong drive (had to fdisk a lot of 160GB drivers from old servers and one still has important data on that client now wants) by running fdisk /dev/sdc & deleting the partitions. The drive is still in a another machine and hasn't been rebooted yet, but

List Readers - I have a Dell server that uses the Perc 6i controller and had 5 1Tb disks installed (1 for OS and the other 4 in a Raid0 for a large storage pool). The owner of the server wanted me to swap out the 1Tb disks for 2Tb disks - easy enough I thought, but I ran into some issues trying to clone the OS disk to the new 2Tb disk, so I just did a re-install. So basically we now have 5 2Tb

Hi, somehow after a power failure i can't mount my ext3 partition :( mount /dev/hdd2 /mnt/gentoo/ mount: you must specify the filesystem type fdisk /dev/hdd The number of cylinders for this disk is set to 484521. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2)

As I understand anaconda uses parted to partition (starting from centos 6), using this as example (kickstart configuration file): clearpart --all --drives=sda --initlabel part /boot --asprimary --size=200 --fstype=ext2 --ondisk=sda part swap --asprimary --size=16384 --fstype=swap --ondisk=sda part / --asprimary --size=512000 --fstype=ext4 --ondisk=sda part /scratch --asprimary --size=1 --grow

Hello Gene, thanks for your reply. Yes BIOS mode. The config wants a menu, which loads fine under ext4 and not under btrfs. Under btrfs I have also tried to remove the syslinux.cfg file altogether (which should trigger the boot: prompt if I am not mistaken) and the result is the same: only the copyright line appears and no prompt. The three letter sequence is EDD. The disk is 160GB, here is the

I have a system running CentOS 6.3, with a SCSI attached RAID: http://www.raidweb.com/index.php/2012-10-24-12-40-09/janus-ii-scsi/2012-10-24-12-40-59.html For disaster recovery purposes, I want to build up a spare system which could take the place of the server hosting the RAID above. But here's what I see: # fdisk -l /dev/sdc WARNING: GPT (GUID Partition Table) detected on

Hi..... I just bought a External HD with USB/FireWire interfaces. I was trying to connect it by firewire and nothing happened, but it's connected by USB, there is no problem. This is the "fdisk - l" output when i connect it by USB Disco /dev/sdc: 160.0 GB, 160041885696 bytes 255 cabezas, 63 sectores/pista, 19457 cilindros Unidades = cilindros de 16065 * 512 = 8225280 bytes

Semi-OT? I just got a new SanDisk 8GB flash drive, and, as usual, it came with the U3 software (for Windoze) on a "CD" partition and considerably less than 8GB on the disk partition. I put it into my WinXP portable and told U3 to delete itself, but I still can't get at the old U3 part of the drive. I've tried WinXP's format command, disk management and CentOS's fdisk,

I am trying to mount a FAT32 partition in CentOS. I'm following the instructions on this page: http://www.linuxforum.com/linux_tutorials/14/1.php This is the line I put into /etc/fstab /dev/hda /mnt/windows vfat users,owner,rw,umask=000 0 0 And this is the error I get: [root at localhost mnt]# mount -a mount: wrong fs type, bad option, bad superblock on

I have my 640GB USB drive connected to a CentOS 5 server and using fdisk, it seems to show a partition of the correct size, /dev/sdd1, but after mounting, the drive shows only 244M size. Does the message received when running fdisk below mean I should reformat this drive, I can't seemed to figure out how to do that with fdisk. Can someone tell me how to reformat, if needed? The drive is empty,

Hey Y'all, I'm trying to mount a USB drive with an NTFS file system on it. I need the drive in a win-7 virtual box instance. Error Dialog is: Error mounting: mount exited with exit code 18: Error opening '/dev/sdc1': Read-only file system Failed to mount '/dev/sdc1': Read only file system [root at mushroom /]# ls -l /dev/disk/by-id | grep usb lrwxrwxrwx. 1 root root

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm working with XenServer 5.5u2, which is basically CentOS 5. I'm having trouble creating a partition. I should still have free space in the extended partition, but it won't let me create any more logical partitions. Is there anything I'm doing wrong or is this a bug in fdisk? Command (m for help): p Disk /dev/sda: 1999.8 GB,

Hello, I had a scientific linux 3.0.4 system (rhel compatible), with 3 ide disks, one for / and two others in linear raid (250 gb and 300 gb each). This system was obsoleted so i move the raid disks to a new scientific linux 3.0.7 installation. However, the raid array was not detected ( I put the disks on the same channels and same master/lsave setup as in the previous setup). In fact