similar to: No automatic refresh?

what is the format of this file? what is the best way to access it w/o the smbstatus program? IE: with perl -sv

How do i unsubscribe??

Dear Xen community, I have Xen 3.0 installed on RedHat Linux Enterprise RHEL4U2. "xend install" runs fine with no error messages. However, when I start "xm cr guest-vmx.conf" I do not get any new window open for the new guest OS. "xm list" shows that the vmx has started and seems to be working fine (just for testing, when I type "xterm" an X window

Hi, I have this scenario Cisco 5300 (public ip. 200.47.xx.xx) <---> Asterisk (public ip: 64.76.xx.xx) <--> Cisco 3600 (public ip: 64.76.xx.xx , same network than * ) When a calls comes in Cisco 5300, this send this calls with SIP to *, asterisk plays a welcome message and resend call to Cisco 3600 that have 4 analog lines connected... but after cisco play welcome message and when

I have just noticed this message in my kernel logs, reporting the possibility of an error with my memory. This would go a long way towards explaining the problems i''ve been having. This particular error is occuring when i''m not running xen so is obviously not something brought on by xen itself. The strange thing is that the NMI error is always followed by the TLAN: eth0: Adaptor

Hi all, I need help. I have a Linux box with SER as a proxy server with ip phones attached on it , and another linux box with Asterisk and T410 card connect to an E1 line .Whenever there is a call from PSTN it is passed to Asterisk and then to SER box and then to the phone .every time an invalid number dialed from PSTN to SIP phones connected to SER asterisk says that the call is progressing

Folks, I'm fairly new to this whole Linux UPS thingie, but I'd quite like to have a look at getting my UPS to work under Linux and would be grateful for any help in getting a driver. I have a reasonable working knowledge of Linux and software development, and thus am happy to modify config files, alter kernel settings, etc, although I'm no C guru. I have a Kebo UPS-650D, which

Hello, I have a problem with connecting a Digium X100P card to a Brazilian analog line. Can somebody help me out with this problem? My /etc/zaptel.conf is loadzone=br defaultzone=br fxsks=1 My /etc/asterisk/indications.conf [general] country=br [br] description = Brazil ringcadance = 1000,4000 dial = 425 busy = 425/250,0/250 ring = 425/1000,0/4000 congestion =

Hi All: I'm a newbee to Asterisk. I currently working on a project and want to know if Asterisk does support R2 Signaling. Thanks Begra8fl >From: asterisk-users-request@lists.digium.com >Reply-To: asterisk-users@lists.digium.com >To: asterisk-users@lists.digium.com >Subject: Asterisk-Users digest, Vol 1 #3647 - 9 msgs >Date: Tue, 04 May 2004 13:32:00 -0500 > >Send

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 dragen@pbsi.org ?rta: | I am hacing trouble. I can see my linux box from my windows box, I can connect | and browse but I cant delete or modify files. Do I have something wrong? | | The is my smb.conf | | [global] | netbios name = dragenlinux | server string = "DragenLinux" | workgroup = WORKGROUP | security = share | log file =

----- Original Message ----- From: Meenu Gupta To: sabma@lists.samba.org Sent: Wednesday, September 04, 2002 2:21 PM Subject: Smbpasswd file problem Hi , I have installed Samba server on Red Hat Linux7.1. I was trying to provide authenticated access to my shares using the encrypted password via the security = user option in my smb.conf . I have also set the smb password file in the global

Hello Since I am getting a bit concerned about the SCO vs IBM issue, I was wondering if can I can setup Asterisk on FreeBSD is it supported ? Are drivers for Digium cards available on FreeBSD ? Thanks Ajit ----- Original Message ----- From: <asterisk-users-request@lists.digium.com> To: <asterisk-users@lists.digium.com> Sent: Wednesday, July 30, 2003 3:05 PM Subject: Asterisk-Users

Hi all, I have a box running asterisk with T410 connected to a Nortel DMS 100 switch and another box running SER with grandstream phones on it So if there is a call from the pstn it goes from the Nortel to the asterisk and then to the SER box and finally to the phones.if the phone is busy or the number is invalid the * box will first send an ALERT message to the Nortel and say the call is going on

Ever since xen-unstable cset 14308 ("pci back: Fix registration of of filters on subsections of config space") I''ve been getting an MCA on the *2nd* boot of a driver domain using an e1000 NIC. Cset 14308 allowed the proper setup of the PM control registers, so the NIC is put in the D3 power state when the driver domain shuts down. Unfortunately, pci_set_power_state()

Hi! I just gave GlusterFS a try and experienced two problems. First some background: - I want to set up a file server with synchronous replication between branch offices, similar to Windows DFS-Replication. The goal is _not_ high-availability or cluster-scaleout, but just having all files locally available at each branch office. - To test GlusterFS, I installed two virtual machines

I''m trying to figure out how to turn a string into an object. Can anyone point me? Here''s some background. Here''s the part of what I''m trying to do that works. ------------------------------------- @ford = [''mustang'', ''pinto''] make = ''@ford'' puts eval(make) --> produces mustang pinto

Hey guys, I've been using samba for quite some time now (over a year). I have a problem however, and that is that I can not seem to get SWAT to work properly. I need to have SWAT working for some of the management cluebies around here (bad idea if you ask me). Anyways, everything for SWAT is fully installed, and it appears that it works properly. Theres just one problem. You can't save

Is there a posibilty to change all Unix file permissions from the NT-Explorer (not only arciv,hidden,sysem mappig). A solution could bee to extend the context menu with to entries show security and set secutriy (inf - files could do that for example winzip-installation does the sama). This extensions can call for example a rsh programm which will do that job. Does anybody has a solution or ideas

Hi, I have a glusterfs volume replicated on three nodes. I am planing to use the volume as storage for vMware ESXi machines using NFS. The reason for using tree nodes is to be able to configure Quorum and avoid split-brains. However, during my initial testing when intentionally and gracefully restart the node "ned", a split-brain/self-heal error occurred. The log on "todd"

Hello all, We have a script that does a nightly backup of a windows server to a linux fileserver. The linux system uses smbclient to make a tarball of the share. I get this error when running smbclient: Domain=[OURSERVER] OS=[Windows 5.0] Server=[Windows 2000 LAN Manager] tar: dumped 56781 files and directories Total bytes written: 9800680960 write_data: write failure. Error = Connection