similar to: Cause for kernel panic

We have a setup with 15 hosts fibre attached via a switch to a common SAN. Each host has a single fibre port, the SAN has two controllers each with two ports. The SAN is exposing four OCFS2 v1.4.2 volumes. While performing a failover test, we observed 8 hosts fence and 2 reboot _without_ fencing. The OCFS2 FAQ recommends a default disk heartbeat of 31 - 61 loops for multipath io users. Our initial

I made a quick change to syslogd(8) so that it can drop root privileges immediately after starting up. It opens up the log sockets (UNIX and network domains) and writes the PID files before dropping privs. It drops privs before openning log files and writing to users. Therefore, you would need to modify your log file permissions appropriately. As for writing to users, ttys generally are writeable

I have a trio of servers that like to reboot during high disk / network IO operations. They don't appear to panic, as I have kernel.panic = 0 in sysctl.conf. The syslog just shows normal messages, like samba complaining about browse master and then just syslogd starting up. The machines seem to crash when I'm not near the console, usually when I'm trying to pull data off them to

I recently upgraded wine from 0.9.7 to 0.9.12 and while checking out that things were working I started up Google Earth but had the following error in terminal: Message from syslogd@TheVoid at Sun May 7 02:40:26 2006 ... TheVoid kernel: Bad page state at free_hot_cold_page (in process 'GoogleEarth.exe', page c125be60) Message from syslogd@TheVoid at Sun May 7 02:40:26 2006 ... TheVoid

Hello! on my centos 4.4 i have enable selinux, but after this change syslogd can't no more run: # /etc/init.d/syslog restart Shutting down kernel logger: [ OK ] Shutting down system logger: [FAILED] Starting system logger: syslogd: error while loading shared libraries: libc.so.6: cannot open shared object file: No such file or

http://bugzilla.mindrot.org/show_bug.cgi?id=906 Summary: syslog messages from sshd [net] lost Product: Portable OpenSSH Version: 3.8.1p1 Platform: All OS/Version: Linux Status: NEW Severity: minor Priority: P2 Component: sshd AssignedTo: openssh-bugs at mindrot.org ReportedBy: peak at

Hello, It's a bit off topic, but I'm hoping someone has seen this before. I'm running a couple of headless boxes, one is 4.7 release, the other is 4.8 release. Both have the same issue with newsyslog when I've got the serial port enabled for console management. (-h in boot.conf and a getty running on cuaa0 after the boot process) Logrotate tries to send an HUP to syslogd, but

Package: logcheck Version: 1.2.32 Severity: wishlist /etc/cron.daily/sysklogd restarts syslogd at the end of the script. This causes a daily log message, currently missed by logcheck: Jan 14 06:55:22 pyloric syslogd 1.4.1#16: restart (remote reception). I'm currently using this regex in ignore.server.d/local-syslogd: ^\w{3} [ :0-9]{11} [._[:alnum:]-]+ syslogd 1\.4\.1#16: restart \(remote

Something has killed any writes to /var/log/messages. Syslogd is running. Has been off for some time and I just discovered it. Any hints as to what / where to look since syslogd is running? Sam -- Sam W.Drinkard -- sam at wa4phy.net NOAA Cooperative Observer KAGS (snow) http://wa4phy.net Augusta Area Mesonet

Hi all, One of our CentOS 5.3 randomly reboots, at different times of the day, and I can't see why it's doing it. I have looked through the logs, but don't see any thing in there that shows me why it has rebooted. How can I debug this? Here's a snipped from the log, around the time of the reboot: Jun 2 14:59:59 usaxen02 kernel: EXT3-fs: mounted filesystem with ordered data

I had a series of kernel hardware error reports today while I was away from my computer: Message from syslogd at fcshome at Aug 12 10:12:24 ... kernel:[Hardware Error]: MC2 Error: VB Data ECC or parity error. Message from syslogd at fcshome at Aug 12 10:12:24 ... kernel:[Hardware Error]: Error Status: Corrected error, no action required. Message from syslogd at fcshome at Aug 12 10:12:24 ...

lspci shows MSI enabled for PCI device. PCI passthrough works fine. However, as soon as the MSI driver for card is insmodded, kernel panics. This is on xen-unstable. Tried the same with xen-3.3.0 which is supposed to have MSI passthrough, but the same guest shows MSI as disabled. Any else seen this bug, or know of a workaround ? Trace is as follows : ------------[ cut here ]------------

The above mentioned combination results in WoW/Wine crashing my computer completely. It freezes completely. No mouse, no keyboard. It just sits there. I can though login via SSH from another computer, and the load is then sitting at 14-15 (using top), which is a bit high. :) The only way to get it back in normal shape, is a hard reboot. Click the powerbutton for 4 seconds, and hope for the best.

Dear list! I have a little problem, trying to enable logging of deny rule. I have enabled it via kernel: options IPFIREWALL options IPFIREWALL_VERBOSE options IPFIREWALL_VERBOSE_LIMIT=3 It is ipfw2. After that, my inten- tion was to use syslogd and !ipfw *.* /var/log/ipfw.log and newsyslog with /var/log/ipfw.log 600 3 100 * J In rc.conf I have firewall_enable="YES"

Yesterday I activated SELinux in targeted mode, then I rebooted and started receiving some error messages in the system services initialization: ====================================================================== audit(1156518721.252:2): avc: denied { read } for pid=2223 comm="syslogd" name="libc-2.3.4.so" dev=dm-0 ino=50441 scontext=user_u:system_r:syslogd_t

Dear Professor Ripley, I am attempting a large scale mixed-model analysis of longitudinal gene array data using R. I use a 64-bit SGI with 7GB available RAM and 40G logical swap space together with unlimited virual swap space. The OS is IRIX 6.5.24. I use R version 1.9.0 since I have had problems upgrading to R 2.0.1 at 64-bit using native SGI compiler build. I write a serial for (i in

--------------------------------------------------------------------- Red Hat, Inc. Security Advisory Synopsis: Denial of service attack in syslogd Advisory ID: RHSA-1999:055-01 Issue date: 1999-11-19 Updated on: 1999-11-19 Keywords: syslogd sysklogd stream socket Cross references: bugtraq id #809 --------------------------------------------------------------------- 1. Topic: A

Dear All, Would you guy have any advices concerning how to get some data like queue length, pkt size, and so forth, from the running queue. Right now, I modified the queue disc to print out some info I want using printk() and use syslogd to catch those info up. The problem is, in burst, syslogd can''t catch all the msg the queue sent out. Are there any standard or better way to

Hi I have been using RGoogleDocs successfully for some time now but something seems to have happened which is preventing me from accessing my data in google spreadsheets. I get the message: "problems connecting to get the list of documents" when I use getDocs, despite being logged in e.g. sheets.con = getGoogleDocsConnection(getGoogleAuth("username", "password",

Just updated our syslog server to 4.8-STABLE #0: Mon Apr 7 09:39:27 EDT 2003 In my rc.conf I have: # fgrep syslog /etc/rc.conf syslogd_program="/usr/local/sbin/syslog-ng" syslogd_flags="" Syslog-ng starts up appropriately; but syslogd also tries to start now. Since the port's already in use, rc hangs during boot until I ctrl-c at that point. Perhaps something's not