similar to: [PATCH 0/4] Add progress bars

This is an updated and extended version of the original patch: https://www.redhat.com/archives/libguestfs/2010-August/msg00163.html This adds OCaml and Perl bindings (both tested), support for progress bars in virt-resize, and adds progress notifications to a number of the simpler commands. Still to do is to add progress messages to more commands. There are still a few commands which would be

Patch registers SIGTSTP hook where it sends reset terminal color control sequence. Maros Zatko (1): fish: reset the console on ^Z RHBZ#1213844 fish/fish.c | 72 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 72 insertions(+) -- 2.5.0

From: Nikolay Ivanets <stenavin@gmail.com> This patch depends on changes in 'common' sub-module posted here: https://www.redhat.com/archives/libguestfs/2020-February/msg00150.html v3 fixes issue found during code review: - options now appear in alphabetical order v2: Almost the same as v1 except '--blocksize' option description is moved into a common submodule (similar to

Nearly any program that writes to standard output can benefit from this sort of fix. Without it, running e.g., ./guestfish --version > /dev/full would exit successfully, even though it got ENOSPC when writing to the full device. That means regular output redirected to a file on a full partition may also fail to be written, and the error ignored. Before: $ guestfish --version >

From: Nikolay Ivanets <stenavin@gmail.com> This patch depends on changes in 'common' sub-module posted here: https://www.redhat.com/archives/libguestfs/2020-February/msg00099.html v2: Almost the same as v1 except '--blocksize' option description is moved into a common submodule (similar to key-option.pod). v1 was here:

From: Nikolay Ivanets <stenavin@gmail.com> This patch depends on changes in 'common' sub-module posted here: https://www.redhat.com/archives/libguestfs/2020-February/msg00096.html Nikolay Ivanets (1): tools: add '--blocksize' option for C-based tools align/scan.c | 8 ++++++++ align/virt-alignment-scan.pod | 12 ++++++++++++ cat/cat.c

An experimental series that adds support for rsync. Rich.

When --blocksize <val> is provided, qemu command line would add physical_block_size=<val>,physical_logical_size=<val> to -device directive. Example: qemu-kvm \ -drive file=raw.img,cache=writeback,id=hd0,if=none \ -device scsi-hd,drive=hd0,physical_block_size=4096,logical_block_size=4096 \ Signed-off-by: Tuan Hoang <tmhoang@linux.ibm.com> --- fish/fish.c |

This implements most of RHBZ#1367738. I didn't bother with virt-v2v-copy-to-local and virt-win-reg, but all the other tools now have full bash completion. Rich.

This is the same as the previous patch, but the partition type is now chosen automatically from mbr or gpt, unless the user expresses a preference. https://gb.redhat.com/archives/libguestfs/2012-January/msg00136.html Rich.

Patch registers SIGTSTP hook where it sends reset terminal color control sequence using write and fsync. Handler is installed only if signal is not being ignored. Patch uses rl_free_line_state and rl_cleanup_after_signal to unhook readline from terminal, then it calls original TSTP handler using approach in URL below and again hooks readline using rl_reset_after_signal. Handling is based on code

Rather than me explaining over again what it does, I've included the man page below. Rich. ---------------------------------------------------------------------- virt-format(1) Virtualization Support virt-format(1) NAME virt-format - Erase and make a blank disk SYNOPSIS virt-format [--options] -a disk.img [-a disk.img ...] DESCRIPTION

These two patches are probably not completely independent, but separating them is a lot of work. With *both* patches applied, all the tests and extra-tests pass. That's no guarantee however that there isn't a mistake, so I don't think this patch is a candidate for the 1.16 branch, until it's had a lot more testing in development. Rich.

Nothing new in the virt-tail command itself, but the second commit includes a simple test. Rich.

We can use the setfiles(8) command to relabel the guest filesystem, even though we don't have a policy loaded nor SELinux enabled in the appliance kernel. This also deprecates or removes the old and broken SELinux support. This patch isn't quite complete - I would like to add some tests to the new API. I'm posting here to garner early feedback. Rich.

This patch set fixes a two year old bug in guestfish, namely that the 'glob' command does not expand /dev/* patterns. https://bugzilla.redhat.com/show_bug.cgi?id=635971 Rich.

This adds a new tool which does a follow operation (ie. tail -f) on one or more log/text files inside the guest. I've only done limited testing, but it works for me for tailing various long-running builds inside guests which I'm doing at the moment. There are no tests at present. Rich.

Since v2: - Fix the things that Pino mentioned, except the recursion. - Implement Windows support. For Windows support to be sane, I had to inline the add_and_mount code. Rich.

* PATCH FOR DISCUSSION ONLY - NOT TO BE APPLIED * Colin suggested something which seems eminently sensible: https://bugzilla.redhat.com/show_bug.cgi?id=916780 I've been through a couple of rounds of trying to implement this. I started with adding the option as suggested to the guestmount program, but it tended to make the guestmount program more complex. More importantly, adding the option

Hi, the following series adds a --key option in the majority of tools: this makes it possible to pass LUKS credentials programmatically, avoid the need to manually input them, or unsafely pass them via stdin. Thanks, Pino Toscano (2): mltools: create a cmdline_options struct Introduce a --key option in tools that accept keys builder/cmdline.ml | 2 +-