similar to: [PATCH] Fix mkinitrd detection of LVM root on RHEL 4

This is belt and braces, because we've already added it to scsi_hostadapter. --- lib/Sys/VirtV2V/Converter/Linux.pm | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-) diff --git a/lib/Sys/VirtV2V/Converter/Linux.pm b/lib/Sys/VirtV2V/Converter/Linux.pm index 375da48..d5a93a7 100644 --- a/lib/Sys/VirtV2V/Converter/Linux.pm +++ b/lib/Sys/VirtV2V/Converter/Linux.pm @@ -341,7 +341,7 @@

mkinitrd needs to mount files using loop. loop might be a module, so try to load it first. --- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 7 +++++++ 1 files changed, 7 insertions(+), 0 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index 0e469f5..08027b6 100644 --- a/lib/Sys/VirtV2V/GuestOS/RedHat.pm +++ b/lib/Sys/VirtV2V/GuestOS/RedHat.pm @@ -1114,6

The following patches add RHEL 6 guest support to virt-v2v. This was actually quite a lot easier than I expected. * [PATCH 1/4] Update virt-v2v.conf for RHEL 6 virtio support * [PATCH 2/4] Check kudzu exists before attempting to disable it * [PATCH 3/4] Use dracut rather than mkinitrd if it's available * [PATCH 4/4] Properly convert RHEL 6 guest console

These 2 patches are mostly code motion. They were prompted by an apparent augeas error in BZ 613967 which didn't display useful error message. The error seems to happen in Converter::Linux. GuestOS::RedHat had a handy function which displayed verbose augeas error messages. This function moves into the new module where it can be used by both modules. The second patch is an consequential tidy

When installing kernel-2.6.18-128.el5 in a guest with kernel-xen-2.6.18-164.el5xen already installed, and 'root=LABEL=/' on the kernel command line, grubby fails to install a grub entry for the new kernel. It only fails when run under libguestfs. Installing in the original Xen guest works fine. The underlying cause appears to be related to blkid, although I haven't managed to pin it

We were assuming that guests wouldn't use multiple interfaces, or if they did, drive letters wouldn't clash between the interfaces. An ESX guest with a CDROM device breaks this because hard disks will be presented a SCSI, starting at sda, and CDROM devices are presented as IDE, starting at hda. This is in contrast to QEMU, which starts at hdc by default. Firstly, this change causes disks

These checks found not to be useful. --- lib/Sys/VirtV2V/Converter/Linux.pm | 28 ---------------------------- 1 files changed, 0 insertions(+), 28 deletions(-) diff --git a/lib/Sys/VirtV2V/Converter/Linux.pm b/lib/Sys/VirtV2V/Converter/Linux.pm index 87eeeb3..1186430 100644 --- a/lib/Sys/VirtV2V/Converter/Linux.pm +++ b/lib/Sys/VirtV2V/Converter/Linux.pm @@ -133,14 +133,6 @@ sub convert sub

RHEL 3 doesn't have a dynamic /dev. kmod-virtio creates devices nodes for vdX block devices based on what the major number of virtblk was at the time it was installed. This is, in turn, based on the order the modules were loaded in initrd. To try to preserve this precarious state of affairs, when adding virtio drivers to a new initrd we always load the same drivers as kmod-virtio in the same

This patch series includes a repost of Milan's unmodified RHN support patch because I haven't pushed it yet. On top of that patch, it includes the capabilities patch in as many bits as I could make it into. The big one is 7/8. I've tested all of the following guests both with and without RHN registration: Xen RHEL 54 PV Xen RHEL 51 PV Xen RHEL 48 PV ESX RHEL 54 FV

There were 2 issues in the code which checked for an existing grub entry before adding a new one. Firstly, it didn't take account of the fact that the passed-in kernel path is relative to root, whereas the grub entry is relative to the grub filesystem, which is normally /boot. Secondly, it expected return from inside eval{} to exit the function, when in fact it only exits the eval. ---

Add a function to display more complete augeas errors if they occur. Update all uses of augeas in GuestOS::RedHat to use it for error reporting. --- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 185 ++++++++++++++++++++++++------------- 1 files changed, 121 insertions(+), 64 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index cf8787d..8b211f0 100644 ---

Handle the case where grub refers to a kernel which doesn't exist by ignoring that kernel. --- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 46 +++++++++++++++++------------------- 1 files changed, 22 insertions(+), 24 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index 77d9332..10ff77d 100644 --- a/lib/Sys/VirtV2V/GuestOS/RedHat.pm +++

--- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index cd2f8e6..380dacb 100644 --- a/lib/Sys/VirtV2V/GuestOS/RedHat.pm +++ b/lib/Sys/VirtV2V/GuestOS/RedHat.pm @@ -862,6 +862,9 @@ sub remove_application $g->command(['rpm', '-e',

--- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 5 +++-- 1 files changed, 3 insertions(+), 2 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index a973c19..6dc4c95 100644 --- a/lib/Sys/VirtV2V/GuestOS/RedHat.pm +++ b/lib/Sys/VirtV2V/GuestOS/RedHat.pm @@ -686,7 +686,7 @@ sub _get_installed error => $error))); } -

--- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index 7c41ff6..ba37001 100644 --- a/lib/Sys/VirtV2V/GuestOS/RedHat.pm +++ b/lib/Sys/VirtV2V/GuestOS/RedHat.pm @@ -1132,6 +1132,11 @@ sub remap_block_devices $g->aug_set($spec,

RHEL 3 has XF86Config instead of xorg.conf. The configs are sufficiently similar to be matched by the same augeas lens, so switch based on whichever is present. --- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 13 ++++++++++++- 1 files changed, 12 insertions(+), 1 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm b/lib/Sys/VirtV2V/GuestOS/RedHat.pm index 1920468..7c41ff6 100644 ---

remap_block_devices was modifying the global device list while remapping device names for libata guests (which includes RHEL 6). This caused a failure later when the renamed devices were not present in the original XML. Fixes RHBZ#641869 --- lib/Sys/VirtV2V/GuestOS/RedHat.pm | 14 +++++++++++++- 1 files changed, 13 insertions(+), 1 deletions(-) diff --git a/lib/Sys/VirtV2V/GuestOS/RedHat.pm

Previously, only the LibVirtXML connection translated network and bridge names in imported metadata. This change moves this functionality in Converter, making it available to LibVirt connections as well. At the same time, the format of the config file is switched to XML. The primary driver for this is that the allowable syntax of a foreign network/bridge name is not known. Rather than create a

We were previously forcing the augeas Modprobe lens to match modules.conf and conf.modules. It turns out that the contents of these files are quite different to modprobe.conf, requiring a new lens. This change keeps the logic which looks for where modules should go, but doesn't update the augeas configuration. If there is no augeas lens for /etc/modules.conf, any attempt to parse or modify it

Previously, only the LibVirtXML connection translated network and bridge names in imported metadata. This change moves this functionality in Converter, making it available to LibVirt connections as well. At the same time, the format of the config file is switched to XML. The primary driver for this is that the allowable syntax of a foreign network/bridge name is not known. Rather than create a