similar to: Broadcom Wifi Problem

This is a continuation of my previous thread: "Broadcom Wifi Problem" Following a post from "James A. Peltier", who said: You can use the rpmforge version or compile it yourself. I've used this one with success using the details described earlier. http://www.broadcom.com/support/802.11/linux_sta.php I did however have to patch it with

Been experimenting with CentOS 5.4 some more. In order to get my wireless card to work (Broadcom BCM4311) I need Broadcom's wl.ko driver (http:// www.broadcom.com/support/802.11/linux_sta.php). It compiles fine after the necessary modification in typedef.h, loads and wireless works. However, as soon as I put some load on that interface (scp something from another machine, download

I'm having a wireless connection issue with an HP laptop and a Zotac media server after the 6.4 package updates from CR repository. Nothing changed with wireless config as far as I can tell. Both have been working fine with previous releases of 6.x. Oddly, if a cat 5 cable is connected for a few seconds and then disconnected the wireless works fine and survives a 'service network

I have an Everex laptop (ick, but it was super cheap) that has an Atheros wireless NIC in it, but I can't seem to get it to connect to my wireless in-home LAN. Here's what I've done so far (that isn't working) - any suggestions? [root at marktop mark]# lspci | grep Ether 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 7c) 05:01.0 Ethernet controller:

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

2009/12/10 Milos Blazevic <milosb at list-solutions.com> > > Hi Ralph, > > I'm a member of CentOS forum and I've tracked problems laptop users are having with Broadcom's wireless hardware (namely, the one(s) in the subject). > Under the circumstances, I had to install one of these myself back in August, which I did - after doing some googleing. Shortly after,

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

I'm trying to bridge a wired network and a wireless network, but I'm having some trouble. No traffic seems to be passing through the bridge. When I issue a "showmacs" command to brctl, I am able to see MAC addresses from both networks. I am also able to ping both networks from the bridge machine. When I issue a "showstp" command to brctl, the wireless access

Dear All, I'm trying to configure wireless card on a Dell Vostro 1540. I had a look at this site : http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom?action=show wireless card :# /sbin/lspci | grep Broadcom 12:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) I decided to follow the ELrepo instructions suggested on the site :

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

I just installed an Asus PCE-n13 wireless card into one of my CentOS 5.6 systems. It uses the RaLink 2680 chip set and I was able to get the driver loaded using modprobe rt2x00pci.ko. I saw no error and now see that the module is loaded along with mac80211 and other dependencies. Now I need to know how to create the wlan0 device. I can find nothing via Google searches on how to create that

Hi Folks I'm trying to get my internal WiFi working and I'm following the instructions here: https://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom My adaptor is: [gary at gary ~]$ lspci|grep Broad 08:00.0 Network controller: Broadcom Limited BCM4352 802.11ac Wireless Network Adapter (rev 03) [gary at gary ~]$ However, I've failed at step 2 as I cannot find any Linux / STA /

Any hope of getting my laptop's Broadcom BCM94311 wireless running on CentOS 5? I find lots of references to using fwcutter to get the needed firmware from Windows drivers, but there's a Catch-22: Version of fwcutter that generate files for the bcm43xx driver in CentOS 5 don't recognize the md5sum of any currently available Windows driver. Newer versions of fwcutter

Hi, i''m trying to use PCI passthrough feature on Xen 4.0 but it fails on my Wireless card. I use Xen 4.0 on a Debian 6.0 (package from repo) and try to passthrough the following PCI device root@omega:~# dpkg -l | grep xen ii libxenstore3.0 4.0.1-1 Xenstore communications library for Xen ii linux-image-2.6.32-5-xen-amd64 2.6.32-30 Linux 2.6.32 for 64-bit PCs, Xen dom0 support ii

Good evening, CentOS community, My name is Gytis Repecka, I am a Lithuanian computer specialist. My acquaintance with CentOS started not so long ago: even though I managed some web servers running Red Hat-based OS for several years, only couple months ago I've set up CentOS on my desktop, later - on a laptop. I've recently solved issues with WLAN on my laptop (thanks to CentOS forum

Dear Samba-List, i'm new to the list and new to samba. Right now I'm trying setup a samba ADDC serving around 50 Windows 10 clients and a couple of linux clients. My ADDC Host has two NICs, eth0 should be connected to the wan - network, eth1 should be connect to a 10.* network, serving the windows and linux clients. The ADDC is up and running, serving only the 10.* network. I

Hi, I have a laptop DELL M90 with an Intel PRO/Wireless 3945ABG card. I'm using centOS 5.1 kernel 2.6.18-53 i386. I installed ndiswrapper v 1.52 I installed the driver http://ftp.us.dell.com/network/R164255.EXE The wireless-tools is v 28.2 When I trying to connect to my wireless access point with encryption key disabled everything work fine !!!! When I enabled the encryption key on my

I'm migrating my son's Dell laptop from Vista to CentOS 5.3. He came back from each of his first two years of college loaded with virii and trojans. This year he said "Dad, can you give me Linux?" 5.3 went onto the laptop easily and after doing some research, I applied the guidance for getting multimedia working and got the nvidia driver loaded. That works great. Last

Hello there! I was running CentOS 6.4 system on my Dell Latitude E6530 flawlessly, until I upgraded to CentOS 6.5. Now the wifi doesn't show up (it's a Broadcom Wifi BT4313, 14e4:4727), I tried to follow the steps from http://wiki.centos.org/HowTos/Laptops/Wireless/Broadcom but when attempting to compile the Broadcom driver module, the make command fails in a way that is not described

Hello David, In brief, I've solved this problem on my Dell Inspiron 1525 (with Broadcom 4312 wireless card), so I figured letting You know would be nice, 'cause it didn't seem like the issue is resolved. Visit this link: http://jomcode.com/fadhil/?p=59 and in addition check out the comment on the same page by Andre Kiepe to have the modules load on boot. Best Regards, Milos.