similar to: Wireless Interface Does Not Connect Automatically At StartUp

Hello, On the Intel Core 2 Duo processor based systems, we have the option of installing either x86_64 or the i386 distribution. I would like to know your experiences with the x86_64 port. How does it compare with the i386 distribution in terms of stability, reliability and performance ? How significant are the performance benefits gained by using the x86_64 linux instead of i386 on the same

Has anyone created or rebuilt a Linux Software RAID having mirrored partitions on unequal sized hard disks ? There is a CentOS 5 server having two 400 GB hard disks with five mirrored partitions (software RAID 1) and one of the hard disks is dying. Since new 400 GB HDDs are not available here, we are exploring the possibility of replacing the faulty hard disk with one of a higher capacity (500 GB

Hello, Does CentOS 5.4 support large ( > 2 TB) external storage devices using GPT (GUID Partition Tables), while the main OS resides on smaller hard disks using MBR. In this scenario, what can be the largest possible size of an ext3 partition (and filesystem) which can be created on the storage array under CentOS 5.4 ? Thanks, Manish

I have a doubt. If you use such a script monitoring the link status with ping and then reconfiguring, why do you need the DGD patch? You need to do some reconfiguration (change multipath to a single default route) anyway if you use the script, right? Also, the DGD patch uses src to lookup the routing table entry, but if you have a dynamic IP for the WAN interface (PPPoE, DHCP etc), this approach

Hello! I read the Split access and Load balancing sections into LARTC (Chapter 4). However I have one gateway only and the LARTC says about 2 links. I need to know how to make a load balance with my links. Thanks in advance. Eriberto - Brazil

Hello, I have configured a load balancing router using Julian''s patches and as described in "nano.txt" for two ISP links as shown below. ISP 1 ISP 2 . . | | | | | | | WAN

Hello, Is there any command / option available on CentOS to expire a user's password immediately ? I remember using "passwd -e" on some other distribution but the -e option does not seem to be present on CentOS 5.x. Thanks, Manish

Hi all! After that good thread "DGD patch not detecting dead gateway" I was able to set up a Load Balancing with ping based DGD (without Julian Anastasov patch). But now I''m facing a new problem and tried some options, with only partial solutions. I made a script based on http://www.mail-archive.com/lartc@mailman.ds9a.nl/msg16257.html (Thank you Manish Kathuria),

This is a new Centos 5.1 install on a HP nc2400 (that use to run XP). Completely clean install; blew away the XP partitions... After applying all the updates, and configuring for the rpmforge repo, I used yumex to install dkms and the dkms-ipw3945, ipw3945-firmware, and ipw3945d rpms. lsmod|grep ipw shows: ipw3945 180391 1 ieeee80211 33417 1 ipw3945 and dmesg)grep

Hi, A friend of mine has 2 lines of 512kbps terminated in two Linux boxes. He now want to remove those 2 boxes and have some device which will loadbalance the two ISPs and also have a failover arrangement. But he has agreed to give me a chance to do it on Linux for my own satisfication. Is this easy to do with lartc? How do I go about it exactly? I have very less time to do it since his

Hello all! I applied http://www.ssi.bg/~ja/routes-2.6.8-10.diff patch to kernel 2.6.8.1 and it works fine, or almost fine. It does the load balancing well, but when one link is dropped it continues to try it. At the end of http://www.ssi.bg/~ja/nano.txt it is said to ping gateway 1 and gateway 2, for the kernel to know if that route is working, but since my linux is connected to the links

How are the updated kernels released by Red Hat / Cent OS related to the latest vanilla kernels ? Are the changes, new features and drivers, etc. available in the newer kernels also ported to the updated kernels released by Red Hat in their entirety ? For the lifetime of a distribution like RHEL 4 or RHEL 5, Red Hat would stick to the same major and minor number of the kernel and would just

Dear Sir, Please help me in building the right solution. My requirement is: 1st I want to club both ISP bandwidth to get 512kbps. 2nd, In normal condition, it should be in Load balancing. 3rd , In ISP Failover condition, traffic will automatically route to working ISP. What I have: I have installed the RHEL 3.0 with 3 Network Card. Kernel is 2.4.21-9EL I have the link from two ISP both

hello i have slackware installed and i have two internet connections , ADSL(2,5mbps) + CableModem(1mbps) i want to share the connections in a small network NAT for the ADSL connection, and a proxy server for the cablemodem connection i searched all over the internet (probably not where i was supposed to) but i could''n find a solution if someone could give me a tip i would really

sir, i have connected multiple clients with he server.i dont know how to play that simultaneously as i m receiving the stream.live playback? On 3/29/07, icecast-dev-request@xiph.org <icecast-dev-request@xiph.org> wrote: > > Send Icecast-dev mailing list submissions to > icecast-dev@xiph.org > > To subscribe or unsubscribe via the World Wide Web, visit >

Hello, This is on Centos 6 and not something I think is wrong with Centos 6 but I am looking to see if anybody else has experienced this and if there is solution. So thanks up front for indulging me. Because Linux makes routing decisions before SNAT it is causing problems when trying to use FTP with two upstream providers in a load balanced setup. Other than ftp, things seem to work OK. Below

Manish Kathuria wrote: > Sandeep Agarwal wrote: >> Manish Kathuria wrote: >> >>Sandeep Agarwal wrote: >> >> >> >> >> >> I have gone through http://www.ssi.bg/~ja/nano.txt AND further >> >> http://www.ssi.bg/~ja/ & got confused in choosing the right patch. >> >> Please suggest if I will choose Jumbo Patch

I am facing problems assigning the owner and group to an ext3 filesystem being mounted from an external storage. I created a mount point /vol and changed its owner and group to alpha and beta respectively (as required). The ext3 filesystem (LV from the external storage) was then mounted on /vol using the mount command. However, after mounting the filesystem the owner and group of /vol changed

I have been successfully implementing load balancing gateways for multiple ISP links at various locations using Julian''s patches and as suggested in LARTC HowTo. At one location, one of the ISPs is providing connectivity through a PPOE DSL link which has to be dialled in everytime to connect. The gateway has been configured on a Fedora Core 3 based system and I have recompiled the

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0