similar to: CentOS-QA Mailing List

I have a CentOS 5.6 system (recently installed) that, for some reason, has decided to mangle one of its drives, specifically /dev/hde1 ... No errors anywhere, just rebooted the machine over the weekend and it's gone. Up till the reboot, the drive was fine, I was writing to it without a problem. fdisk tells me: ---------- # fdisk -l /dev/hde Disk /dev/hde: 160.0 GB, 160041885696

Hey everyone, Is anybody aware of a /true/ active/active multi-head and multi-target clustered iSCSI daemon? IE: Server 1: Hostname: host1.test.com IP Address: 10.0.0.1 Server 2: Hostname: host2.test.com IP Address: 10.0.0.2 Then they would utilize a CLVM disk between them, let's call that VG "disk" and then directly map each LUN (1,2,3,4,etc) to LV's named 1,2,3,4,... and

In case you didn't see it, the initial CentOS 6 trees have been released to QA: http://qaweb.dev.centos.org/node/81 -- Paul Heinlein <> heinlein at madboa.com <> http://www.madboa.com/

Posted, in case you haven't seen it already: http://qaweb.dev.centos.org/qa/node/116 Good news.

Jeff Sheltren has been providing timely and clear updates about the status of the 6.3 release: http://qaweb.dev.centos.org/ They're much appreciated! Thank you very, very much. -- Paul Heinlein heinlein at madboa.com 45?38' N, 122?6' W

Hello CentOS it took a few days before i got the hang of it http://email.about.com/gi/dynamic/offsite.htm?zi=1/XJ&sdn=email&zu=http://cnbc7.com

Hi all, I am running 5.4 After running sudo yum clean all sudo yum update We got it upgraded to 5.6 cat /etc/redhat-release CentOS release 5.6 (Final) So, how can I get it my CentOS from 5.6 to 6.0? [vuhung at -08 ~]$ sudo yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: mirror.vietoss.com * extras: mirror.vietoss.com * updates: mirror.vietoss.com

What is the best way to install CentOS 6? Is there an upgrade facility from CentOS-5.6? If so, how does this compare with a clean installation? -- Timothy Murphy e-mail: gayleard /at/ eircom.net tel: +353-86-2336090, +353-1-2842366 s-mail: School of Mathematics, Trinity College, Dublin 2, Ireland

Hi Folks, CentOS 5.5 x86_64 Asrock-Board with 2 USB3 plugs. Normally USB3-drive is detected. But occasionaly after "umount" next time this drive or other ones will not be detected. I have to boot the PC - than it works - till next unrecognition. On USB2 plugs all works correct. No messages in /var/log/messages nor dmesg. What happens here? Board failure - or other reasons? Some

The QA web site at http://qaweb.dev.centos.org/qa/blog was really helpful for those of us who were curious as to how CentOS 6.0 was coming along. However, there doesn't seem to be much information as to how CentOS 6.1 is going from either the QA web site, the forums (Announcements), or Kananbir's twitter feed -- but it may be I'm just not looking in the right place. Does the QA

Hi guys, Sorry for the OT. For the last couple of weeks I notice that the static in my server room is worrisomely noticeable. I cannot see what may be causing it.... Care to share some of your experience what may be the cause and the remedy? Thank you.

We need to replace several servers, quickly - four of our Dell PE 1950's died in one week. (!!!) So, we're looking around, and I was checking out IBM. I customized to what we want, and hit 'continue', and suddenly there's another $800 for a "system common planar" that's "required". Googling only finds specs with it - does anyone know what it is? I mean,

Greetings- Is there any updated news on the CentOS6 front? As per qaweb [1], today should be the day of QA signoff and syncing to internal mirrors. Are things still on track? --Tim [1] http://qaweb.dev.centos.org/qa

(I'm doing tests in a VirtualBox instance, so take this with a grain of salt.) If you give the VM only 512 MB of RAM, the text-mode installer kicks in. It does not prompt you to configure anything related to the network or hostname. The system boots up without a network interface configured. Also, it won't let you choose the install mode, I guess it defaults to Minimal (which is fine

I just want to say that I really, really, appreciate the information given on this site: http://qaweb.dev.centos.org/qa/calendar -- *** E-Mail is NOT a SECURE channel *** James B. Byrne mailto:ByrneJB at Harte-Lyne.ca Harte & Lyne Limited http://www.harte-lyne.ca 9 Brockley Drive vox: +1 905 561 1241 Hamilton, Ontario fax:

For those who don't follow the QA RSS, see: http://qaweb.dev.centos.org/qa/node/120 to get the latest info on the status of 6.2. Looks good so far!

Hi, I want to make secure my python http server.. what should i use ? chroot ? there are something more secure ? On my centos server I've SE enabled..then .. sandboxing ? Thanks very much lewis -- Linux and Windows 2003/2008 Server. http://predellino.blogspot.com/

Hi, I just finished installing a CentOS 5.6 x86_64 system and the first thing I wanted to do after the install is to apply the software patches. But I get the following error when I try to run 'yum update': Package libuser-0.54.7-2.1.el5_5.2.x86_64.rpm is not signed and yum update exits without applying any of the patches. I tried clearing the cache and re-running the update

When starting IPERF with "iperf -s" or "iperf -sD" it seems to stop after client runs its first test. I would like to leave it running for a few hours to give someone a chance to run a few tests. Is there a way to leave it active on the server and kill it manually later?

Hello dear friends Anyone know if in the U.S is going to organize the FLISOL? Especially in the state of Michigan. -- Fidel Dominguez-Valero Linux User: 433411 Website: http://www.valerofix.ryanhost.net