similar to: sendmail, port 465/587, auth and imap

Hi Not sure whether this is the correct list to ask ... if it's not please direct me to the correct one. Is it possible on to log a bit more detail when auth failure occurs when using saslauthd? saslauthd[2119]: do_auth : auth failure: [user=DELETED] [service=smtp] [realm=DELETED] [mech=pam] [reason=PAM auth error] What I want is the IP address and if possible the incorrect password

On Tue, Apr 25, 2017 at 07:15:43PM -0700, John R Pierce (pierce at hogranch.com) wrote: > On 4/25/2017 7:00 PM, Jobst Schmalenbach wrote: > > snip > > client request originated from, so logging the IP of the failed request had > best be done at a higher layer. Good answer, makes sense. As for the higher layer used - can be either sendmail or imaps as both use the saslauth. Just

Hi. I am trying to configure sendmail that is looks up the users credentials to allow them to send email via that server via an imap server on the same machine when sending email while on the road. I can send email when specifying a user that is stored in the servers /etc/shadow ... no problem but I cannot get my head around it how to do make saslauth OR sendmail lookup the user creds via the

On Wed, Sep 11, 2019 at 09:43:32AM -0400, Jonathan Billings (billings at negate.org) wrote: > On Wed, Sep 11, 2019 at 01:34:27PM +1000, Jobst Schmalenbach wrote: > > CentOS 7.X, sendmail.x86_64 8.14.7-5.el7, cyrus-sasl.x86_64 2.1.26-23.el7 > If you look at the systemd unit for saslauthd, you can see this: > > [Unit] > Description=SASL authentication daemon. >

Hi. I am stuck with this one and I do not know where and how to search for this problem nor do I know how to fix it. When I reboot one of our servers (CentOS 6.7, selinux target, yum fully updated) the http server loads fine (no erros) but when accessing one of the server's websites it displays "Forbidden", restarting the httpd server (command line) will give full access and all is

Hi. Is there any way to limit access to dovecot by domains. I only need to give access to a well known set of domains, all from Australia and all networks are known and used either from people at home or mobile access (phones, laptops etc). iptables is not possible as e.g. OPTUS does not give away all of the networks mobile phones are connected to. I know some, but not all. It would be much

Hi I have two different IP addresses (in a block of /29), one is on port 0 and the other is on port 2 of a Ciso 888. I am doing this so I can have two different certs with two different ip addresses. I have tried: 1) one machine, two real interfaces, two cables (eth0 and eth2) 2) one machine, one real interface eth0 and one virtual interface eth0:1, one network cable Using number 2) I can

Hi. IMHO there is a bug in the latest updater for clamav: * it places a freshclam script into /etc/cron.daily that uses a hardcoded datadir not defined in /etc/clamd.conf its never done that before in the last 5 years or so, and I have a script running from cron.d * its overwrites the permissions of existing directories (lib and log) to another new clamav user, although one already exist

Hi. I am getting loads of errors "no backend defined for idmap config MYDOMAIN" after I upgraded from 3.5 -> 3.6 a couple of days ago. I read http://wiki.samba.org/index.php/Samba_3.6_Features_added/changed and did what man smb.conf suggested: idmap config MYDOMAIN : backend = tdb idmap config MYDOMAIN : range = 500-1999999 yet I still receive those errors. I used

I have a server with no desktop - just cli that i need to have a user plug in a usb hd and would like it to automount to a consistent directory so I can schedule a backup. The user can rotate the usb drives and it all just works. Any ideas how automate so that say /media/backup mounts to any usb harddrive and unmounts cleanly? -thx bazooka

Hi. I downloaded the the "Remote Server Administration Tools" but whenever I want to add the group policy snap in I get the subject error message even though I am logged in as domain admin on the client work station. System(s): * CentOS 6.7 (all latest patches except samba due to one XP machine I have to keep due to legacy software, but not long!) * Clients are all Windows 7 bar 1

Hi I have had this problem for a while, but waited to post this until I upgraded to see whether the upgrade would fix it. I upgraded samba to the 4.2.X stream from 3.6.X stream, but it happens on both, 3.6.X and 4.2.10. Whenever someone logs out, then in again the profile gets corrupted and a new TEMP profile is created (the dreadful "creating new desktop"). Now I do not know where

On Tue, Apr 25, 2017 at 07:14:56PM -0700, Gordon Messmer (gordon.messmer at gmail.com) wrote: > On 04/25/2017 07:00 PM, Jobst Schmalenbach wrote: > > What I want is the IP address and if possible the incorrect password (just to see how far they are off). > > Is this possible? > > I hope not. That's a terrible idea. Every time a user fat-fingers their > password, your

Whether I like it or not I need to get a version of PHP that is greater than 5.2.1 as the latest SugarCRM version require this and as I am a module developer I need to have one of the later versions of PHP on my machines. Does anyone know of a reliable and good archive for PHP that provides higher versions than the ones supplied by the upstream provider? Thanks Jobst -- 'Two things

Hi. I have two internet connections, the ADSL2+ is very very cheap (but fast 10mb) and I want to use the SHDSL (2mb) only for mail,ssh,http OUT and the ADSL2+ only for surfing. I all works fine if people specify the proxy in the browser, but in case like flash it of no use. Further if I can make the 80/443 traffic go through the proxy only, its an added bonus. If this can be done, fine. Bue I

Hi I am not sure how to solve this. I am constantly getting messages that should go into the kern/message log printed on screen - MOSTLY from iptables. The messages are ALSO logged to the syslog files. It still prints those message onto the console screen even if I am logged off (security issue). When logged in on the console its anoying as I constantly have to hit CTRL-L to refresh the

Hi I want to setup a SMS system for Nagios on a 5.9 box. I read in a blog that the two modems Huawei [ E160G | E176 ] work with 6.3. Anybody any experience with those modems and do they work with 5.9? Are there any other devices that are better/recommended? Thanks Jobst -- 186,262 miles/second : Not just a good idea, it's the LAW. | |0| | Jobst Schmalenbach, jobst at

Hi. I am trying to find "something" (php prefered) that I can stick onto a Centos apache server that would allow me to browse a selected file system by employees through a web-browser "explorer like" interface. I know I can do this through WinSCP (and have done so), but my problem is I have Linux, Windows and MAC clients and my knowledge of MAC's is rather limited. I

Hi. How do I give access to shares from the LOCAL administrator account to a share(s) on the samba server? (workstation is domain member, without the need to specify a password). -------------------------- smb.conf domain logons = Yes os level = 200 domain master = Yes security = user -------------------------- I have read chapters 12,13,15 but there seems to be no way I can put the

On Thu, Oct 05, 2017 at 02:57:18PM +1300, Clint Dilks (clintd at scms.waikato.ac.nz) wrote: > On Thu, Oct 5, 2017 at 2:41 PM, Jobst Schmalenbach <jobst at barrett.com.au> > wrote: > [snip] > Hi, > > Are you sure that your issue isn't related to the mirror that your > systems are selecting ? If they are using different mirrors I would try > using the