similar to: CentOS and Dell MD3200i / MD3220i iSCSI w/ multipath

Greetings, On 1/22/11, Edward Morbius <dredmorbius at gmail.com> wrote: > CentOS is not a Dell-supported configuration, and we've had little helpful > advice from Dell. There's been some amount of FUD in that Dell don't seem > to know what Dell's own software installation (the md3 > > Dell doesn't seem to have much OS experience generally. > +1 It is

Hi all, I have a Dell server running cent 5.6, new install, connecting to an IBM DS3500. I have configured iscsi connections using iscsid and can log into the targets on the IBM. I can also mount the LUNs when accessing them from their active controller path. When I throw multipath into the mix, it fails completely. Multipath is working, when I run multipath -ll it shows me the correct active

Hi list! I have a server with dual port Qlogic iSCSI HBA. I set up the same LUN for both ports, and boot the CentOS installer with "linux mpath". Installer detects multipathing fine, and creates mpath0 device for root disk. Installation goes fine, and the system boots up and works fine after the install from the multipath root device. After install the setup is like this: LUN 0 on

We''re currently designing a ZFS fileserver environment with iSCSI based storage (for failover, cost, ease of expansion, and so on). As part of this we would like to use multipathing for extra reliability, and I am not sure how we want to configure it. Our iSCSI backend only supports multiple sessions per target, not multiple connections per session (and my understanding is that the

Hello! I have trouble with multipath routing. Those options are enabled in kernel: [*] IP: policy routing [*] IP: equal cost multipath [*] IP: equal cost multipath with caching support (EXPERIMENTAL) <*> MULTIPATH: round robin algorithm But issuing: ip r a 1.2.3.0/23 scope global equalize nexthop via 80.245.176.11 \ dev eth0 weight 1 nexthop via 80.245.176.13 dev eth0

Hello, I am trying to find out a best practice for a specific scenario. First of all I would like to know what is the proper way to set up multipath, who should care about it the host or the guest. Right now I have a setup where I have one multipath which sets my host to boot from FC SAN. I have another multipathed LUN in the host which is essentially a dm which I attached to a guest, however

Hello, I hope to be in the right list. my question is the following. I can''t seem to get multipathing configure on XCP 1.6. In XenCenter I was able to enable "Multipath" however, in the LUN under general tab I see " multipath 1 of 1 active", the the CLI I do the following command xe --m node session it list only one session. Can someone help me please? Thanks in

# cat /etc/redhat-release CentOS Linux release 7.1.1503 (Core) # uname -r 3.10.0-123.20.1.el7.x86_64 Hi, We use iSCSI over a 10G Ethernet Adapter and SRP over an Infiniband adapter to provide multipathing to our storage: # lspci | grep 10-Gigabit 81:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection (rev 01) 81:00.1 Ethernet controller: Intel Corporation

I've got my RAC cluster running pretty smoothly now (thanks again for all the help so far), but I only have single connections between the servers and the RAID array. The servers each have two Qlogic HBAs, and I'd like to find out if there's any reasonable way to implement multipathing. The platform is RHEL 3, and Red Hat's knowledgebase indicates that they strongly recommend

Greetings, I've hit this exact 'bug': https://bugzilla.redhat.com/show_bug.cgi?id=491311 I need to remove the mappings manually. I assume this is done via 'multipath -F' followed by a 'multipath -v2' ? Has anyone experienced doing this on a production system? We can do it during hours of low activity, but we would prefer to keep the databases on this host online at

Hi, I do have one iscsi storage with 4 GBit nics of which currently only one is configured with an ip and which is in productive use by one cent os 6.3 server. Doing some research brought me to the idea to use some nic bonding or multipathing for that storage, but multipathing I did about four or five years ago only once :) Furthormore I can't find the ultimate answer (may be there is not

I have a new Dell PowerEdge 2950 running CentOS 5.0 out-of-box and a Dell MD3000i. I am new to iscsi and, with google and included documentation, am having a heck of a time trying to get the RAID volumes I have created on the 3000i to be seen by the OS as usuable drives. I have printed out SMcli and iscsiadm documentation. I have asked on the linux-poweredge at dell.com site, too. Many

hi all We have a rh linux server connected to two HP SAN controllers, one an HSV200 (on the way out), the other an HSV400 (on the way in). (Via a Qlogic HBA). /etc/multipath.conf contains this : device { vendor "(COMPAQ|HP)" product "HSV1[01]1|HSV2[01]0|HSV300|HSV4[05]0" getuid_callout "/sbin/scsi_id -g -u -s /block/%n"

Dear list, we have a relatively new Sun Storage 7310, where we connect CentOS 5.5 Servers (IBM LS21/LS41 Blades) via Brocade Switches, 4GBit FC. The Blades boot from SAN via qla2xxx, and have no harddisks at all. We want them to use multipathing from the very beginning, so /boot and / are already seen by multipathd. Problem is, that the Sun 7310 has two storage heads which run in

Where can I find a list of supported multipath drivers for ZFS? Keith McAndrew Senior Systems Engineer Northern California SUN Microsystems - Data Management Group <mailto:Keith.McAndrew at SUN.com> Keith.McAndrew at SUN.com 916 715 8352 Cell CONFIDENTIALITY NOTICE The information contained in this transmission may contain privileged and confidential information of SUN

Hi, I got few servers (IBM HS20,HS21 blades, IBM xSeries 3650 & others) connected to a dual fabric san throught Qlogic HBA's (23xx, 24xx). Multipathing is done with device-mapper-multipath. On CentOS 4.x i can scan for new scsi devices without any problems, get them up with multipathing & use them without any problems. However, after i started installing CentOS 5.1 (did not

Using CentOS 5.1, though with a few hours work I could update to 5.2.. I can install to SAN with a single path no problem but I'd like to be able to use dm-multipath. From the kickstart docs it seems this is supported but there is no information as to what the various options mean http://www.centos.org/docs/5/html/5.1/Installation_Guide/s1-kickstart2-options.html -- multipath (optional)

I'm trying to test out an Equallogic PS5500 with a server running CentOS 4.7 I can create a volume and mount it fine using the standard iscsi-initiator-utils tools. The Equallogic box has 3 Gigabit interfaces and I would like to try to set up things so I can read/write from/to the volume using multiple NICs on the server i.e. get 200+ Mbyte/s access to the volume - I've had some

I am attempting to get multipath working with device-mapper (CentOS 4.2 and 4.3). It works on EVERY install of mine from RH (also v4.2, 4.3), but the same multipath.conf imported to all my installs of CentOS do not work. Note that I have tested a working 4.2 configuration file from RH on CentOS 4.2 and a working 4.3 configuration (it changed slightly) on CentOS 4.3. Neither worked. Our production

Hello, suppose I want to use a special configuration for my IBM/1814 storage array luns, then I put something like this in multipath.conf devices { device { vendor "IBM" product "^1814" product_blacklist "Universal Xport" path_grouping_policy "group_by_prio" path_checker