similar to: Fail Transfer of Large Files

Hi, I am having some difficulties with matrix operations. It is a little hard to explain it so please bear with me. I have a very large data set, large enough that it needs to be split in parts in order to deal with. I can work things on these "parts" but the problem lies in adding together these parts for the final answer. So that been said, let's say that i split the data in 2

In the control script of my daemon in /etc/init.d?, I have # chkconfig: 35 97 3 The result of this is that I have links: /etc/rc.d/rc1.d/K03... /etc/rc.d/rc3.d/S97... /etc/rc.d/rc5.d/S97... As mentioned in a previous thread, my complex daemon throws an exception when I shutdown. Perhaps things might be better if I had: /etc/rc.d/rc3.d/K03... Might this be a good idea? If so,

On my CentOS box, in C++ programs, is there a way to print Unicode characters? Thanks, Mike.

I learned from Anne that if I boot to level 5, after I enter the username, can select Gnome or KDE. I note that the default is always Gnome. How can I make the default KDE? How can I get KDE with startx after booting to level 3? Thanks, Mike.

On my laptop, I have not been able to get KDE to run; I always get gnome. I installed selecting KDE, and I tried yum groupinstall, which appeared to work, but I still get gnome running. BTW, I boot to level 3, and run startx. Thanks for your suggestions. Mike.

Hi, In populating our racks with several gigbit switches over the next few days, i'm wondering this: Is it over-engineering to seek out 550mhz rated cables over the typical Cat 6 250mhz rated cables? I've been advised (if you can a salesperson's words advice, heh.) that 250mhz is enough to handle traffic up to 10GB's. Should I just be happy with Cat6 for my GB switches or is

Hello, on an x64 ubuntu 15.10 desktop tinc 1.0.26 sometimes crashes on startup of the machine. eth0 (via good old cat6 cable, no wireless) is configured to use dhcp. The crash does not happen often, I have seen it in total maybe 2 or 3 times since installing 15.10 while it was still in alpha ( July 2015 ) until today. The desktop is not shut down very often, maybe once a week or every two weeks

On my CentOS 6 partition of my laptop: First note that for this test, NetworkManager is not running because I did: chkconfig --del NetworkManager and then rebooted. Here is my ifcfg-eth0: DEVICE="eth0" NM_CONTROLLED="no" ONBOOT=no HWADDR=xx:xx:xx:xx:xx:xx TYPE=Ethernet BOOTPROTO=none IPADDR=192.168.2.5 PREFIX=24 GATEWAY=192.168.2.1 DNS1=192.168.2.1 DNS2=192.168.2.1

In a context where exceptions are caught, I ran the fragment: cerr << "allocating" << endl; char* arr[100]; for (int jj = 0; jj < 10; ++jj) { cerr << "jj = " << jj << endl; arr[jj] = new char[2000000000]; sleep (30); } sleep (10); for (int jj = 0; jj < 10; ++jj) delete[] arr[jj]; cerr

I have to provision several dozen * users to a seperate building on our campus in the same subnet. Ordinarily, I'd just run a gigabit cat6 cable to another switch if it doesn't violate the 100 metre rule, but this building is several hundred metres away from my backbone. My only option for cabling to the remote building is copper. My plan is to provision them with a Linux bridge with 4

I've been tasked with fitting out an appartment building with a phone system. The entire appartment is getting broadband, with Cat6 Cables into each appartment and fibre down the trunk. I was hoping to have PSTN in the basement connecting to the IP system. Today I found out however that one of the services will be paid TV - and it will need a PSTN backchannel - ie a modem. The set top

On my Centos box with: uname -r 2.6.18-164.6.1.el5 I tried to mount my 2T external drive with: mount -t ntfs /dev/sdg1 /mnt/wd and I get: mount: unknown filesystem type 'ntfs' Thanks in advance for your help. Mike.

I have a C++ program that opens, gets a little data from, and closes about 5000 files. Now if I run the program when I first boot up, the running time is from about 10 seconds to a minute. Subsequently, the program runs in well inter one second. Buffering -- right? So I changed a parameter, so the program gets a different (albeit similar) 5000 files from a different directory. Running time on

On my newly installed CentOS 6 I am running KDE (I think; I selected it in the setup, but how would I know?). It has three default icons: Computer; Root's Home; Trash. I do not see them in /root/Desktop. How can I remove them? Thanks, Mike.

On my laptop, I boot CentOS 6 to level 3and find the font is quite small. Is there a way to change the font size at level 3? Thanks, Mike.

Where can I get the latest pan newsreader that would work with KDE 4? Thanks, Mike.

Running: yum list available | grep -i gmime shows results for CentOS 5, but not for CentOS 6. It seems to be needed by my pan. What should I do? Thanks, Mike.

Hi, I am trying to optimize my gigabit network. I have two Intel 1000 MT Gigabit Server Adapters, which support Jumbo Frames -- as well as a Switch that supports Jumbo Frames. However, I am observing some strange behavior in my file transfers from Windows XP to Linux and I am wondering if it has anything to do with the way the Samba variables are set on my Linux box? The "strange

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

I've done all the googling I can on this, and have come to the conclusion that a Grandstream BT101 can be abused to be a door phone. Could someone with access to one, confirm that the following is possible? Researched: 1. When set to auto-answer, dialing the phone will result in a short beep and instant speaker-phone connection. 2. When pressing the "message" button while