similar to: CentOS 5.5: bind config is missing the slave zone definitions

It should work fine. What esxi version you are using? Eero 4.11.2015 6.27 ip. "Boris Epstein" <borepstein at gmail.com> kirjoitti: > > > > > > > > was the controller you added the virtual disk to an IDE or scsi > controller? > > > > -- > > public gpg key id: 1362BA1A > > > > _______________________________________________

Hello all, I am trying to get djbdns ( http://en.wikipedia.org/wiki/Djbdns ) running on CentOS 7. So far I have wirtten the djbdns.service and djbdns.socket files. The sockets (TCP and UDP 53) for some reason would not start and I don't know how to debug that; the service does start but only when I start it manually by running systemctl start djbdns So, I am a real noob when it comes to

Hello Julius, Thanks - but it doesn't seem to work. I installed sg3_utils and ran #scsi-rescan but that seemed to have done nothing for some reason. Cheers, Boris. On Wed, Nov 4, 2015 at 10:12 AM, Tnjulius <tnjulius at gmail.com> wrote: > Hi Boris, > Just rescan the scsi host. > #scsi-rescan #if you have sg3_utils package > #lsscsi > Or > #echo "- - -"

Hello listmates, I have two seemingly identical (in this reglard, at least) machine - both of them are running CentOS 6.2 with bind (bind-chroot) installed. I used webmin to edit the DNS configuration. One one of them it seems to work fine, on the other I get messages akin to the following: Failed to create master zone : Failed to replace /var/named/chroot/etc/named.conf with

Hello listmates, I have encountered a rather peculiar situation. We have a Centos 6 VM (64 bit) running on a VMware vSphere 5.5 server. It was running just fine until one day I decided to reboot it and it just would not boot up. Effectively, dracut failed to initialize the LVM, much like under the scenario described here:

Hello all, If I were looking for a load balancer to run on a Linux - specifically, CentOS - machine - what would you recommend? Thanks. Boris.

Hello listmates, Yes, I know - Macs and NFS do not co-exist easily. Still I've got to make this happen somehow. In short - we have two CentOS-based NFS servers. They work fine with a variety of Linux machines but when I try to mount them from a Mac OS X 10.5 or 10.6 machine I get nowhere. I.e., the Mac does not complain yet reads nothing over the NFS. Has anybody seen this? Does anybody

Hello all, Is there a way to recognize a hot-plugged disk (i.e., to get the system to recognize it and build the appropriate /dev/sd* device for the new device) without a reboot? Thanks. Boris.

Hello listmates, I am wondering if there is a set of scripts/utilities for automatically starting and running headless (no X11) VM's using VirtualBox omn a CentOS 6 server. VNC/RDP access to the VM's would be fine. Any help much appreciated. Cheers, Boris.

Lucian, So far here is the best we could find out: https://bugzilla.redhat.com/show_bug.cgi?id=1084747 Testing to see if this is the solution; so far it seems to be. Cheers, Boris. On Tue, Jan 13, 2015 at 2:49 PM, Nux! <nux at li.nux.ro> wrote: > Use BIND. How the times have changed. :-) > > PS: I'm also curious for a solution.. for when djbnostalgia hits me. > >

Hello all, The question is not necessarily CentOS-specific - but there are lots of bright people on here, and - quite possibly - the final implementation will be on CentOS hence I figured I'd ask it here. Here is the situation. I need to configure a Linux-based network load balancer (NLB) solution. The idea is this. Let us say I have a public facing load balancer machine with an public IP

OK, thanks again for all your help. I have resolved this, finally. The problem was that I configured VLAN 48 as the native VLAN on the trunk port.That was a mistake as apparently the native VLAN is the one where Cisco does not bother to tag packets. For now I set the native VLAN to VLAN 1 and that works. Cheers, Boris. On Sun, Jan 25, 2015 at 7:13 PM, Boris Epstein <borepstein at

Thank you everyone. OK, the mystery deepens, I guess. The machine does need to support several VLAN's, it is currently on a trunkport (8021q encapsulated), it made it into the ARP table - which I specifically tested for by physically unplugging the table, clearing the ARP table and plugging it back in. The ARP table currently looks like this: hq#show arp Protocol Address Age (min)

Do you need the whole configuration? On the switch end, we have the relevant VLAN (VLAN 48) with the assigned IP address of 192.168.48.101 and the range of ports (Gi1/0/1 - Gi1/0/8) assigned to that VLAN. Seems - and acts - like a legitimate setup and works fine, except for this particular instance. Thanks. Boris. On Fri, Jan 23, 2015 at 8:54 PM, Dennis Jacobfeuerborn < dennisml at

Less, You are 100% right. Of course I brought up my eth0 - but, like you said, with no IP. Meanwhile, I brought up eth0.48 with 192.168.48.100. However, until I would bring up eth0 with an IP address (any in the network) I would have no connection. Why? That's what I fail to understand. Boris. On Fri, Jan 23, 2015 at 6:45 PM, Les Mikesell <lesmikesell at gmail.com> wrote: > On

Hello listmates, I can't find the 32 bit version of Centos 7. Would it be because I am not looking in the right place or does it not exist at all? Thanks. Boris.

Hello listmates, So, what's the story with CentOS 6? It is supposed to be out by now, or coming out soon, or so I heard - but yet there seems to be no mention of it at http://centos.org/ . Does anybody know what's up with that? Thanks. Boris.

Hello everyone, This is not directly related to CentOS but still: we are trying to set up some storage servers to run under Linux - most likely CentOS. The storage volume would be in the range specified: 8-15 TB. Any recommendations as far as hardware? Thanks. Boris. -------------- next part -------------- An HTML attachment was scrubbed... URL:

On Thu, Nov 5, 2015 at 8:23 AM, Tris Hoar <trishoar at bgfl.org> wrote: > On 04/11/2015 20:59, John R Pierce wrote: > >> On 11/4/2015 12:52 PM, Boris Epstein wrote: >> >>> I don't get this for some reason... not even sure why. ESXi's default >>> behaviour seems to be to allow hotplug, that does not seem to be >>> deactivated. I am just

Hello there, I successfully use automount to mount a large XFS pargtition on one CentOS 5.5 machine. I then tried to do the same thing on a different machine - and it simply would not work! The configuration is done in the same fashion, I checked and double-checked the syntax - but it is still a no go. When I use the mount command the partition mounts perfectly. I have tried running automount