similar to: wireless

Hi folks I have my Linksys WUSB54GC USB wifi card already working. Now I have another issue. Accidentally I tuned off my AP, and when switched it on again my wireless link is still down. I have to unplug the USB card and plug it again to get it working again. I'm new in wireless matter but this doesn't sounds logical to me. What if I loose the link for whatever reason? Should I have to

I have a system that does *not* have a graphical desktop installed, nor do I ever plan to. I have its wired ethernet working just peachy. Now I want to configure a USB wireless ethernet and scratching my head. Particularly since I don't use NetworkManager, everything is manually configured. That said, if I enable NM, I see this in /var/log/messages: NetworkManager[26900]: <info>

I just installed an Asus PCE-n13 wireless card into one of my CentOS 5.6 systems. It uses the RaLink 2680 chip set and I was able to get the driver loaded using modprobe rt2x00pci.ko. I saw no error and now see that the module is loaded along with mac80211 and other dependencies. Now I need to know how to create the wlan0 device. I can find nothing via Google searches on how to create that

Hi folks I just installed Centos 5.5. I heard about the new changes in wifi support. I tried a USB wifi card from Netgear, and It works fine. It didn't en Centos 5.4, so that's great news. The problem is I have a Linksys WUSB54GC USB wifi card and I want to make it work. I get this messages in /var/log/messages as soon as I plug it in. Oct 14 22:56:20 lila kernel: usb 1-1: USB

I am trying to get wireless working on CentOS 7.3 with intel wireless 3165 ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000 link/ether b8:ae:ed:77:b3:3a brd ff:ff:ff:ff:ff:ff 3: wlan0:

Hi all, I am trying to configure wlan0 interface to use it with kvm guests. I know that I need to use ebtables statements due to it is not possible to link wlan0 interface with a bridge. I have followed Debian's tutorial: https://wiki.debian.org/BridgeNetworkConnections#Bridging_with_a_wireless_NIC without luck. Someone have tried?? I am using CentOS 7 fully patched. Thanks.

Hello, Thanx in advance to anyone who can help me get this going. I have tinkered around and around with this and I have it functioning as a visible access point that I can connect to. My problem comes in when trying to access the internet. I''m not an iptables guru or anything but I got the following as my iptables startup to supposedly masq the connection correctly:

Hi guys, I have a problem with my Centos 6.4. I am experiencing a Wireless Disconnects, some time ago I had them constantly each 2-3minutes. After upgrading to new kernel (and other software from "Software Update" I am still exepriencing disconnects but every 10-15 minutes. It makes me angry because I am doing a lot of work with ftp servers. Card: *Atheros Communications Inc. AR9285

Hello, I have the AR9285 wireless adaptor on an HP DV6-2128ca notebook. I can see it. it comes up in NetworkManager but never gets an IP. the router is a linksys using WPA/PSK security. Would/could someone please help me out trying to get this to work? Output of several commands follows: dmesg: ath: EEPROM regdomain: 0x69 ath: EEPROM indicates we should expect a direct regpair map ath:

Hello I've got this Mini-PC https://www.zotac.com/product/mini_pcs/zbox-ci323-nano everything is fine -> latest 6.8 kernel works; both Ethernet-Interfaces work and also the WLAN-Interface works; the two Ethernet-Interfaces are eth0 and eth1 the WLAN-Interface is wlan0 eth1 is connected on ISP side eth0 is connected on my LAN side to a switch; and wlan0 shall also be on my LAN side f?r

Hi, I have a laptop DELL M90 with an Intel PRO/Wireless 3945ABG card. I'm using centOS 5.1 kernel 2.6.18-53 i386. I installed ndiswrapper v 1.52 I installed the driver http://ftp.us.dell.com/network/R164255.EXE The wireless-tools is v 28.2 When I trying to connect to my wireless access point with encryption key disabled everything work fine !!!! When I enabled the encryption key on my

Hi all, I'm trying to configure wireless on my Asus laptop running CentOS7. I see wlan0 when I type iw dev, but if I type ip link set wlan0 up I get the following error: RTNETLINK answers: Operation not possible due to RF-kill Any idea what is wrong?? Adrian -- Adri P. van Bloois Antonlaan 104 email: adrian at pa0rda.nl 3701 VG Zeist voice: +31-(0)-30-6912741 The Netherlands fax:

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

I know people used Parprouted to help with bridging wired with wireless. Have a look at it. -- Sent from the Delta quadrant using Borg technology! Nux! www.nux.ro ----- Original Message ----- > From: "C. L. Martinez" <carlopmart at gmail.com> > To: "Discussion about the virtualization on CentOS" <centos-virt at centos.org> > Sent: Thursday, 24 September,

Hi all, I'm trying out bridging for my wireless and wired LAN, so that they can both use my PPPoE connection. Here's the network structure, pretty easy: darjeeling (192.168.1.7) ringo (192.168.1.3) (mtu 1500) (mtu 1500) \ / \ wlan0 <--br0 (mtu 1500)--> eth1

On Thu, Sep 24, 2015 at 2:08 PM, Dmitry E. Mikhailov <d.mikhailov at infocommunications.ru> wrote: > On 09/24/2015 04:47 PM, Alvin Starr wrote: >> >> Actually I do a similar thing. > > Do you? > >> I use a VM as my home/office firewall. > > If your laptop/server/smth is permanently wired to the internet, there's no > problem to bridge this interface

Folks Is there a way in CENTOS6 to define and turn on wireless from the command line. My environment is as follows: I'm trying to build a laptop for travel, and have KVM-guests for both Linux Gui and Windows, using internal NAT networking. The underlying host machine doesn't really need to be much more than a NAT provider, and the usual command-line utilities. When I arrive at a

On 04/02/16 21:29, Adrian P. van Bloois wrote: > Hi all, > I'm trying to configure wireless on my Asus laptop running CentOS7. > I see wlan0 when I type iw dev, but if I type > ip link set wlan0 up > I get the following error: > RTNETLINK answers: Operation not possible due to RF-kill > > Any idea what is wrong?? your laptop has a switch to turn on/ turn off the wifi

Hello, I'd like to add rules (level workstation) for ignoring wlan reconnects/disconnects. The rules would ignore messages like this: May 12 11:02:16 t400 kernel: [13254.204101] No probe response from AP <MAC> after 500ms, disconnecting. May 12 11:02:16 t400 kernel: [13254.213029] cfg80211: Calling CRDA to update world regulatory domain May 12 11:02:16 t400 wpa_supplicant[3277]:

Hi everyone! :-) Yesterday I managed to find a driver for my USB wireless dongle, and it is now correctly recognized by the kernel. However, I don't know how to configure it. The system-config-network opens up in text mode and is not very forthcoming (it lists ethernet, ISDN and modem as possibilities for configuring a new device). I don't know how to create an