similar to: kvm boot options

Jerry Geis <geisj at pagestation.com <http://lists.centos.org/mailman/listinfo/centos>> wrote: >/ So I thought I would try those same options on my r4000 />/ laptop. they had no effect.... This AMD turion 64 4000+ />/ rating laptop is still running SLOWWW... />/ /proc/cpuinfo has the cpu Mhz running at 2393 / Yes, the 4000+ is 2.4GHz. >/ below is my dmesg output for

Hi, I have a v2000 compaq laptop. The realtek network and USB on this machine was not working. After adding to grub.conf "acpi=off apci=off noacpi noapic" the v2000 realtek started working and the USB worked fine... Fantastic! So I thought I would try those same options on my r4000 laptop. they had no effect.... This AMD turion 64 4000+ rating laptop is still running SLOWWW...

I use kvm-amd a lot to do test installs. I am using it with qemu-kvm-0.14 the lastest. I think your supposed to be able to give your command line and add the parameter " -boot dc" so it initially boots with the cdrom (d) and then after reboot will boot do the HD or c. This never works for me. It always boots CDROM. Is anyone using this argument. Is there something special to do in

I am using the following command below to create a boot floppy file. Am I not doing the correct thing? mkbootdisk --device bootfloppy.img 2.6.9-34.0.1.EL cp: writing `/tmp/mkbootdisk.Jb5537/vmlinuz': No space left on device cp: writing `/tmp/mkbootdisk.Jb5537/initrd.img': No space left on device cat: write error: No space left on device cat: write error: No space left on device Jerry

Is there a way to use kvm-amd on centos 5.1? I dont want to mess with XEN. I want the hardware virtualization that is on my AMD chip. I played with putting 2.6.24 and centos 5.1 on my AMD laptop, got kvm-amd and that works. However I want to put this on my desktop that is running 2.6.18-53.1.14.el5. Is there a way or do I just wave to use 2.6.24 or 25. Thanks, Jerry

I am wanting to use the mkfs.hfsplus as mentioned here http://www.oli.id.au/createosxdmgdiskimagesinlinux but I dont have the command. yum provides "*/mkfs.hfsplus" returns no packages found. Where do I find this command? Thanks. Jerry

>insmod <module> should do it On 31/12/05, Jerry Geis <geisj at pagestation.com <http://lists.centos.org/mailman/listinfo/centos>> wrote: >/ />/ If you specify noprobe at boot can you then manually />/ specify to load the 8139too network module? If so how? />/ />/ Thanks, />/ />/ jerry I am trying to to boot with askmethod to do an nfs install I did the

Hi, What modules are needed in my mkinird command with --preload to boot from usb thumbdrive? THanks, Jerry

> > On Wed, Jun 18, 2008 at 10:21 AM, Karanbir Singh <mail-lists at karan.org <http://lists.centos.org/mailman/listinfo/centos>> wrote: > >/ Jerry Geis wrote: > />>/ > />>/ What went wrong? > />/ > />/ Also, I can see you are still doing your old "ask on the list rather than > />/ actually work out what the problem is" trick :/

Hi all, I have setup my Cisco 79XX phone. Did the tftp, put the config files in the right location with the right names. Booted my phone, it does the tftp things, the screen shows my extensions everything seems fine. However, when I come offhook and try to dial 11 which is just a playback of demo-congrats in the dialplan the phone says Calling Out (INV) below is my sip.conf file - I presume it

Is there any performance lost in using a software raid array with only 1 disk? I was wanting to use the mdadm monitoring tools to monitor the machines single disk drive for failures and such. Is there any performance hit for such a setup? Some machines have RAID some machines dont (for me) and I was thinking about a common setup. Also then if I want in the future I can actually just add the

If you specify noprobe at boot can you then manually specify to load the 8139too network module? If so how? Thanks, jerry -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20051231/f5a89ead/attachment-0001.html>

On Tue, Apr 19, 2016 at 5:42 AM, Jerry Geis <geisj at pagestation.com> wrote: > I have a laptop with windows 10. > I went into the Windows disk manager and shrunk the volume > to make room for C7. That worked. > > I also changed the BIOS from secure boot to "both" (secure/legacy) Both is a problem. There's no practical way for an installer to support both.

All - I am running a virtual windows 7 (pro 64) on centos 5.5 x86_64. I was hoping to run virtual XP inside windows7 in this configuration. I get an error about cannot start virtual XP when I try this. Do I not have something setup correctly or can I not run a "double" virtual environment? Thanks, Jerry

I am trying to get timing paramters from a CGI program. date is just a command for example used here. when I do: time { date; } everything is good. when I do: time -o file { date; } I get time -o file { date; } bash: syntax error near unexpected token `}' How do I correctly issue the command with an option for -o file to output the data to a file. Thanks, Jerry

I have a dell inspiron 8200 laptop running centos 4.1 just fine. I want to connect it to an external 32 inch LCD. This laptop is dual boot windows. I set windows up to 1024x768 and connected the LCD - it worked just fine. LCD max is 1333x768 I then booted Centos 4.1 and set X to be 1024x768 also. rebooted the laptop just ot make sure. I then connected the LCD and it says can't display

Hi, I was wanting to run the equivalent of "hdparm -Tt /dev/hda" except on a SATA hard disk. What is the equivalent command for an SATA drive? I was wanting to see what kind of speed I am getting on the SATA drive. thanks, Jerry

Hey I was wanting to play with xen on beta 5. I have the beta 5 installed in my turion laptop. Went smooth... (4.4 would not install) Anyway anyone know were a starting point with xen might be? Thanks, Jerry

hi I am new at CentOS.I am not able to install webmin at Centos.if there is no problem at webmin installing at Cent .where I will get the webmin rpm for Cent. Thanks shahriar Quoting centos-request at centos.org: > Send CentOS mailing list submissions to > centos at centos.org > > To subscribe or unsubscribe via the World Wide Web, visit >

I am sending an email from my machine devcentos5x64. the transcript below (hangs for 60 seconds) at the line: MAIL From:<root at devcentos5x64.msgnet.com> SIZE=56 AUTH=root at devcentos5x64.msgnet.com The email succeeds - but I am trying to figure out the 60 second delay. Neither email server is busy. Nothing is waiting. the DNS on both machines point to the same nameserver. The DNS