similar to: Trying to get a grasp on NTP server/client access control options

On my member server, running 'ntpq -p' yields: ntpq -p localhost: timed out, nothing received ***Request timed out The ntp.conf file is trying to use the DC's hostnames addresses: user at DC01:~# cat /etc/ntp.conf # /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for help driftfile /var/lib/ntp/ntp.drift # Enable this if you want statistics to be logged. #statsdir

Copied Roweland's DC ntp.conf file into my two DC's. Restarted (all) ntp. Member still timing out! (I am starting to think that there is 'something' about the sernet packages that "they" do differently.) Rowland, Could I ask you to copy the ntp.conf from your client (appears to be your laptop) so I could review it's contents? --- ------------------------- Bob

Thank you, Rowland. Copied your simpler ntp.conf file into my member server. Made the appropriate changes. Restarted all the ntp service on all machines (just in case.) Ran 'ntpq -p' (on member server) and got the correct answer. Proper connection to DC's. --- ------------------------- Bob Wooden of Donelson Trophy 615.885.2846 (main) www.donelsontrophy.com [1] "Everyone

Made the suggested adjustments (4 locations in the member server ntp.conf file) and restarted ntp. Still (member server) timing out. Not sure what you mean about removing "server 0.debian.pool.ntp.org iburst" lines. Those on the DC's. Aren't they necessary? Running 'ntpq -p' on DC's results in correct response. --- ------------------------- Bob Wooden of

I have two DC's running Version 4.1.16-SerNet-Debian-9.wheezy and a member server running Version 4.1.11-Debian. When I 'ntpq -p' from the member server I get: localhost: timed out, nothing received ***Request timed out Member server ntp.conf file: cat /etc/ntp.conf # Local clock (this is not the localhost address!) server 127.127.1.0 fudge 127.127.1.0 stratum 10 # The source,

Hello, I recently compiled Samba 4.0.6 (as an AD DC) and am running it on Ubuntu 12.04. I followed the instructions on the Samba wiki (https://wiki.samba.org/index.php/Configure_NTP) for how to configure ntp, however the domain clients are rejecting the DCs as being acceptable time sources. Below is my ntp.conf: server 127.127.1.0 fudge 127.127.1.0 stratum 10 server 0.pool.ntp.org iburst

It appears that none of our windows clients are syncing their time with the samba DC.??? From what I can tell they are not able to get a response from the DC.? For example, where the DC is named athena: >w32tm /monitor /computers:athena athena[10.10.1.10:123] ? ICMP: 0ms delay ? NTP: error ERROR_TIMEOUT - no response from server in 1000ms From a Linux machine there is

Hai Flavio, > -----Oorspronkelijk bericht----- > Van: samba [mailto:samba-bounces at lists.samba.org] Namens > Flávio Silveira via samba > Verzonden: woensdag 13 september 2017 16:19 > Aan: samba at lists.samba.org > Onderwerp: Re: [Samba] File server questions > > > > Em 13/09/2017 10:36, L.P.H. van Belle via samba escreveu: > > Hai, Flavio, > >

Em 13/09/2017 10:36, L.P.H. van Belle via samba escreveu: > Hai, Flavio, > > Yes, it looks good, but i suggest, if you setting up a new DC on debian.. > Go here: https://github.com/thctlo/samba4/tree/master/howtos > And read the file: stretch-base-2-samba-minimal-ad.txt > > This should works also for debian Jessie, if it errors only remove the words " limited" from

On Wed, 25 Oct 2023 11:53:07 -0500 Ham via samba <samba at lists.samba.org> wrote: > It appears that none of our windows clients are syncing their time > with the samba DC.??? From what I can tell they are not able to get a > response from the DC.? For example, where the DC is named athena: > > >w32tm /monitor /computers:athena > > athena[10.10.1.10:123]

> On 10/25/2023 9:53 AM PDT Ham via samba <samba at lists.samba.org> wrote: > > > It appears that none of our windows clients are syncing their time with > the samba DC.??? From what I can tell they are not able to get a > response from the DC.? For example, where the DC is named athena: > > >w32tm /monitor /computers:athena > >

> On 10/25/2023 11:16 AM PDT Rowland Penny via samba <samba at lists.samba.org> wrote: > > > On Wed, 25 Oct 2023 11:53:07 -0500 > Ham via samba <samba at lists.samba.org> wrote: > > > It appears that none of our windows clients are syncing their time > > with the samba DC.??? From what I can tell they are not able to get a > > response from the

I’m currently trying to install a new (primary) AD DC in a Linux container. It seems to me that being in a container, the DC is easier to maintain and backup than on bare metal, and I prefer a container over a VM for performance reasons. If the container setup will prove to be too much of hassle, I’ll switch to a VM, though. The first issue I’m facing is time synchronization. An container cannot

Hi Louis, In general, this sounds like the solution I was looking for. But I’m still a bit unclear about the practical implementation. So, the DC can be setup without ntpd as it will work based on the system clock which, in turn, is actually being updated by the container host using NTP. Which means we’ve got the DC itself covered. But if ntpd is not installed, then how can the DC serve time

Hi All, I am currently running a setup with a main DC ad1, that has ntpd installed and is currently configured to retrieve the time from the UK NTP time pool. I also have a second backup AD DC, ad2, on which I have not installed ntpd but I have installed ntpdate. My current understanding is that the setup I have just described is in-line with the recommended best practices outlined in the

Hello, I have a question regarding signed NTP support for Samba4 on Ubuntu 12.04. I have followed most of the steps outlined here: https://wiki.samba.org/index.php/Configure_NTP These steps I did differently are: * I did not install from source because the latest Ubuntu package for ntp available on Ubuntu 12.04 includes ntp-signd support already * I did not install Samba4 to /usr/local/samba, so

Hi, I configured my NTP server in samba 4 according to the article " https://wiki.samba.org/index.php/Time_Synchronisation" however I verified that the NTP server does not respond to requests from Windows NTPv3 clients, it only responds to NTPv4. Following my ntp.conf: # /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for help driftfile /var/lib/ntp/ntp.drift # Enable this if

I just realized that some of my Windows 10 clients do not appear to be syncing the time correctly. I setup NTP to run on my Netgate PFSense server. It is using pfsense.pool.ntp.org Time Servers. I configured NTP on my Samba servers to point to back to the PFSense Server. NTP on the samba servers have the following ntp.conf files: # /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for

On 13/02/15 19:48, Bob of Donelson Trophy wrote: > > > Thank you, Rowland. > > Copied your simpler ntp.conf file into my member server. Made the > appropriate changes. Restarted all the ntp service on all machines (just > in case.) Ran 'ntpq -p' (on member server) and got the correct answer. > Proper connection to DC's. > --- > >

On 13/02/15 17:26, Bob of Donelson Trophy wrote: > > > Copied Roweland's DC ntp.conf file into my two DC's. Restarted (all) > ntp. Member still timing out! > > (I am starting to think that there is 'something' about the sernet > packages that "they" do differently.) > > Rowland, Could I ask you to copy the ntp.conf from your client (appears