similar to: APC Smart-ups "status codes" (slightly OT)

Well, here's the tale: we got a "replacement kit" for some APC SmartUPS 3000 - rackmount UPSs. The "kit", costing about half of what APC is asking, is just the batteries, and you pull the tray out, open it up, and swap out the batteries. Except, I did this on one... and the replace battery light never went out. Not using apcupsd's apctest, not pushing the button. The

Hi All, About a month ago APC announced they were including MODBUS protocol support in their new APC UPSes. The technical note on this is here: http://www.apcmedia.com/salestools/MPAO-98KJ7F/MPAO-98KJ7F_R0_EN.pdf "Application Note #176 Modbus Implementation in APC Smart-UPS" The APC "announcement" appeared on their site in their user blogs by an APC employee, here:

Hello Ted, 2013/9/11 Ted Mittelstaedt <tedm at mittelstaedt.us> > Hi All, > > About a month ago APC announced they were including MODBUS protocol > support in their new APC UPSes. The technical note on this is here: > > http://www.apcmedia.com/**salestools/MPAO-98KJ7F/MPAO-**98KJ7F_R0_EN.pdf<http://www.apcmedia.com/salestools/MPAO-98KJ7F/MPAO-98KJ7F_R0_EN.pdf>

Hi, I am trying to set up NUT on a mini-ITX system running OpenBSD 5.5. I have an APC Smart-UPS SC620 which runs perfectly well on Ubuntu, with nut-2.2.1. Ubuntu system uses ASUS motherboard. On mini-ITX system, I have Intel d2500cc motherboard with 4 serial ports. I've tested ports by connecting them with a null-modem cable and running cu in 2 terminals. Type in one terminal, output shows

Hello. Trouble to communicate with APC SmartUPS via serial port. UPS connected to the com1 port on windows host. Communication witch hyperterm works well. There is a log: YSM ^ASmart-UPS SC1000 n5S0713T63247 m03/29/07 L240.0 B27.10 apcupsd also can communicate with the UPS and works well. running apcsmart -a ups gives the following: com1: device reports different attributes than what were set

Hi there, I am using an old (really old) APC Smart-UPS 600. It worked fine under apcupsd but when I tried NUT it did not work. The error I was getting was: sudo /lib/nut/apcsmart -DDD /dev/ttyS1 Network UPS Tools (version 2.0.4) - APC Smart protocol driver Driver version 1.99.8, command table version 2.0 debug level is '3' Attempting firmware lookup Firmware: [D4] Not found in

On 2014-01-14 10:12, dstrr wrote: > Hello. > Trouble to communicate with APC SmartUPS via serial port. > UPS connected to the com1 port on windows host. > Communication witch hyperterm works well. > There is a log: > > YSM > ^ASmart-UPS SC1000 > n5S0713T63247 > m03/29/07 > L240.0 > B27.10 > > apcupsd also can communicate with the UPS and works well. >

On May 2, 2014, at 3:26 AM, Kastus Shchuka wrote: > Hi, > > I am trying to set up NUT on a mini-ITX system running OpenBSD 5.5. > > I have an APC Smart-UPS SC620 which runs perfectly well on Ubuntu, > with nut-2.2.1. Ubuntu system uses ASUS motherboard. > > On mini-ITX system, I have Intel d2500cc motherboard with 4 serial ports. > I've tested ports by connecting

Hi, we bought two Smart-UPS X 1500 FW:UPS 09.1 / ID=20 lsusb -v: Bus 002 Device 002: ID 051d:0003 American Power Conversion UPS Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor

Hello I recently switched from apcupsd to NUT2.2.2 without any troubles. I tried to figure out how I can configure the self-test intervall. The command upsrw lists only the variables battery.charge.low battery.runtime.low ups.delay.shutdown ups.delay.start The command usbhid-ups -D and the listing under http://obsvermes.org/cgi-bin/nut/upsstats.cgi?host=apcsmart at localhost&treemode

John R Pierce wrote: > On 11/17/2017 7:16 AM, m.roth at 5-cent.us wrote: >> I can't seem to find apcupsd for C 6. Just went to epel's website, and >> not >> visible. Anyone have a clue? >> > > suggestion, use NUT instead, the Network UPS Tools....? works for all > sorts of UPS's, not just APC, and supports a master/slave sort of > network control

On Dec 16, 2014, at 9:45 AM, Frantz de Germain <frantz at info.univ-angers.fr> wrote: > Bye the way I just realize that I can't retrieve the ups.load, among other > thing :-( To the best of my knowledge, Microlink is not supported by any third-party tools (including NUT), but some variables are exposed via standard USB HID. Apparently, ups.load is not one of them. Your UPS might

On Jul 9, 2013, at 9:04 AM, Gregor Burck wrote: > we bought two Smart-UPS X 1500 FW:UPS 09.1 / ID=20 [...] > I see there should be problems to get it work with a free daemon like nut, but are there some hints using it? > In my ups.conf I tried: > > [apc001] > driver = apcsmart > port = auto > desc = "Smart APC" Only the USB drivers should

> > On Fri, 2010-01-29 at 16:53 -0500, m.roth at 5-cent.us wrote: <battery change tale o' woe snipped> >> But the idiot light's still on. <snip> Well, I followed the link to the NUT info, and tried a "manual" calibration, and still no joy. Swapping in a cartridge that's still good, the light goes out, so it's not the unit. However, googling for

> I have a disk box from ACNC (Jetstor 416is) that has an UPS port. The manual describes an UPS port: “2. Uninterrupted Power Supply (UPS) Port (APC Smart UPS only) The subsystem may come with an optional UPS port allowing you to connect APC Smart UPS device. Connect the cable from the UPS device to the UPS port located at the rear of the subsystem. This will automatically allow the subsystem

Ok, so another apc UPS 3000 complained about bad batteries, and I changed them out from the same order that I'd gotten in a couple of months ago. The APC SmartUPS 3000 started connecting and disconnecting the USB connection. I brought down and up the service, no joy. Finally, after googling, I found a *completely* undocumented way to start apcupsd, that a few years ago someone was told to

Hi All, hoping someone might have some insights to what is going wrong with my NUT setup and my APC Back - UPS RS 1500 (specifically a BR1500GI) using the usbhid driver. https://download.schneider-electric.com/files?p_File_Name=AHUG-9JU4RH_R0_EN.pdf&p_Doc_Ref=SPD_AHUG-9JU4RH_EN&p_enDocType=User%20guide Main issue: NUT successfully shuts down my server when it goes on battery but when

Listmates, After wrangling with the voltage value on the CyberPower 1000AVRLCD and now having 2 of them working, I though it would be a simple matter to move my APC BP650 from apcupsd to nut so that all 3 servers would be monitored on the same web interface. The APC is attached to an older box running openSuSE 11.0 with nut-2.2.2-66.1. (nut-classic). The APC BP650 uses a serial connection

Hi, folks! There is FreeBSD 7.1, NUT 2.4.1, UPS APC Smart 2200 XL. NUT is compiled from ports with following options: --------------------------------------- _OPTIONS_READ=nut-2.4.1_5 WITH_SERIAL=true WITH_USB=true WITH_SNMP=true WITHOUT_NEON=true WITHOUT_PDU=true WITHOUT_HAL=true WITHOUT_IPV6=true WITHOUT_CGI=true --------------------------------------- UPS is successfully recognized by OS

I can't seem to find apcupsd for C 6. Just went to epel's website, and not visible. Anyone have a clue? mark