similar to: /etc/cron.weekly/99-raid-check

this has never happened to me before, and I'm somewhat at a loss. got a email from the cron thing... /etc/cron.weekly/99-raid-check: WARNING: mismatch_cnt is not 0 on /dev/md10 WARNING: mismatch_cnt is not 0 on /dev/md11 ok, md10 and md11 are each raid1's made from 2 x 72GB scsi drives, on a dell 2850 or something dual single-core 3ghz server. these two md's are in

CentOS 6.3, x86_64. I have noticed when building a new software RAID-6 array on CentOS 6.3 that the mismatch_cnt grows monotonically while the array is building: # cat /proc/mdstat Personalities : [raid6] [raid5] [raid4] md11 : active raid6 sdg[5] sdf[4] sde[3] sdd[2] sdc[1] sdb[0] 3904890880 blocks super 1.2 level 6, 512k chunk, algorithm 2 [6/6] [UUUUUU]

Saturday I did an upgrade from 5.3 (original install) to 5.4. Saturday night, /etc/cron.weekly reported the following: /etc/cron.weekly/99-raid-check: WARNING: mismatch_cnt is not 0 on /dev/md0 md0 holds /boot and resides, mirrored, on sda1 and sdb1. md1 holds an LVM volume containing the remaining filesytems, including swap. The underlying hardware is just a few months hold,

hi, we've a few 10-20 server in a lan each has 4-8 hdd. we'd like to create one big file server on these server hard disks and we'd like to create it in a redundant way ie: - if one (or more) of the hdd or server fails the whole filesystem still usable and consistent. - any server in this farm can see the same storage/filesystem. it's someting a big network raid5-6... storage where

hi, after we switch our servers from centos-3 to centos-4 (aka. rhel-4) one of our server always crash once a week without any oops. this happneds with both the normal kernel-2.6.9-11.EL and kernel-2.6.9-11.106.unsupported. after we change the motherboard, the raid contorller and the cables too we still got it. finally we start netdump and last but not least yesterday we got a crash log and a

Does software raid 1 compare checksums or otherwise verify that the same bits are coming from both disks during reads? What I'm interested in, is whether bit errors that were somehow undetected by the hardware would be detected by the raid 1 software. Thanks, Nataraj

hi, withe the latest cvs (and a few days ago) I've got a lot's of such process on the maiul server (and the number of such processes just growing:-(((). anyway the login problem disapear as I use dovecot as pam module name (both for impa and pop3). ------------------------------------------ root 18923 0.0 0.0 0 0 ? Z 17:35 0:00 [dovecot-auth <defunct>]

Hello, since weeks I was ignoring this warning at my CentOS 5.6/64 bit machine - /etc/cron.weekly/99-raid-check: WARNING: mismatch_cnt is not 0 on /dev/md0 in the hope that the software RAID will slowly repair itself. I also had executed "echo 100000 > /proc/sys/dev/raid/speed_limit_max" on the advice from the mailing list. But now my web server is offline - I had to boot

hi, i create rule such action.AllowPostGrey: ----------------------------------------------- ###################################################################################### #TARGET SOURCE DEST PROTO DEST SOURCE RATE USER/ # PORT PORT(S) LIMIT GROUP ACCEPT $A_IP $PORTAL_IP tcp 10023 ACCEPT

hi, we use openvpn as for our vpn endpoints and we''ve got about 70-80 vpn connections which means we have tun0 - tun80 interface. i''d like to define one zone for all of our vpn connections how can I do that? actualy our local zone is 192.168.0.0/17 (not 16) and all of the vpn''s are in 192.168.128.0/17. our should i define somehow the local zone as 192.168.0.0/16? but in

hi, while all files is owned by nsd user and nsd run as nsd the nsd.db is still owned by root user (because the compiler run as root and create this file as root, ok i know just it'd be better if this file is owned by nsd too). another strange thing is that on the slave nsd i've got such messages: ----------------------------------------- zonec: reading zone "lfarkas.org".

hi, it''d be very useful to add some kind of "log everything" option to shorewall. currently the logging is useful if you know what you would like to log. but if you don''t know than it''s a problem... another problem that currently it''s not possible to log the nat table. at least i can''t find any way (can''t add logging into masq and

hi, in the masq file''s documentation, there is a sentence: "If you have a static IP on that interface, listing it here makes processing of output packets a little less expensive for the firewall." this realy means that SNAT to the primary address is less expensive than a MASQ rules in the netfilter? is this documented anywhere in iptables/netfilter? thanks. -- Levente

may here someone can answer me... -------- Original Message -------- Subject: Re: [CentOS-announce] Release for CentOS-5.2 i386 and x86_64 Date: Tue, 24 Jun 2008 18:31:20 +0200 From: Farkas Levente <lfarkas at lfarkas.org> To: The CentOS developers mailing list. <centos-devel at centos.org> References: <4860E6EB.5000906 at centos.org> Karanbir Singh wrote: > > We are

On 08/07/2015 01:04 PM, Johnny Hughes wrote: > 6.7 is there most places ... since we have more than 500 external > mirrors (right now 593) not all of them are updated. (looks like > 4% still are not completely updated) what about the src.rpms? it seems http://vault.centos.org/6.7/os/ and http://vault.centos.org/6.7/cr/Source/ is empty and while

Hi, May be it's not clear to everyone.. so this's just a quick notice to everyone. Don't use CentOS 7 as a developer workstation since currently there is not included any developer IDE. As eclipse was pulled out from the main distro and put into Red Hat Developer Toolset (which is imho a good idea not to use a 7 years old IDE). But Red Hat Developer Toolset is still not supported on

hi, after i test nsd i find the following. if i use this in a zone file: $ORIGIN example.com. CNAME www www CNAME x x A 1.2.3.4 then it's excepted by nsd what's more give the proper result. if the slave is nsd than there is no problem, while if the slave is bind i've got the following error:

hi, is dovecot are support all required feature for kolab imap server? the requirements can be found here: http://www.kolab.org/doc/kolabformat-2.0rc3-html/index.html ie. can i replace cyrus-imap with dovecot in a kolab server? thanks in advance. yours. -- Levente "Si vis pacem para bellum!"

If I have multiple files in cron.weekly and one script takes hours to finish. Will it block other scripts in cron.weekly?

hi, I'm just download the latest cvs and try to use imaps. in mozilla I've got the following message window: ----------------------------- mail.int.bppiac.hu received a message with incorrect Message Authentication Code. If the error occurs frequently, contact the website administrator. ----------------------------- and there is only one OK button:-) and this happens always. what can be