similar to: Karanbir's disks (was: openfiler )

> Simple, it's only a NAS device, and not really a file server / web > server / data base server as well. Here is something I am currently lokoing at, and wondering if you'd considered it or if anyone here has done it. I've got a bunch of existing hardware - really good IBM stuff that is all installed with CentOS (with a few exceptions). We want to move to virtualization, but

Hey folks, We've got some new hardware and are trying to figure out what best to do with it. Either run CentOS right on the bare metal, or virtualize, or several combination options. Mainly looking at : - CentOS on bare metal - CentOS on ESXi 4.0 with local disk - CentOS on ESXi with 1 VM running Openfiler to serve disk to other VMs And want to benchmark these 3 scenarios So far all we

Hi all, I'm setting up Centos4.2 on 2x80GB SATA drives. The partition scheme is like this: /boot = 300MB / = 9.2GB /home = 70GB swap = 500MB The RAID is RAID 1. md0 = 300MB = /boot md1 = 9.2GB = LVM md2 = 70GB = LVM md3 = 500MB = LVM Now, the confusing part is: 1. When creating VolGroup00, should I include all PV (md1, md2, md3)? Then create the LV. 2. When setting up RAID 1, should I

I have configured 2x 500G sata HDD as Software RAID1 with three partitions md0,md1 and md2 with md2 as 400+ gigs Now it is almost 36 hours the status is cat /proc/mdstat Personalities : [raid1] md0 : active raid1 hdb1[1] hda1[0] 104320 blocks [2/2] [UU] resync=DELAYED md1 : active raid1 hdb2[1] hda2[0] 4096448 blocks [2/2] [UU] resync=DELAYED md2 : active raid1

Hi. CENTOS 7.6.1810, fresh install - use this as a base to create/upgrade new/old machines. I was trying to setup two disks as a RAID1 array, using these lines mdadm --create --verbose /dev/md0 --level=0 --raid-devices=2 /dev/sdb1 /dev/sdc1 mdadm --create --verbose /dev/md1 --level=0 --raid-devices=2 /dev/sdb2 /dev/sdc2 mdadm --create --verbose /dev/md2 --level=0 --raid-devices=2

Hi, This is my current config: /dev/md0 -> 200 MB -> sda1 + sdd1 -> /boot /dev/md1 -> 36 GB -> sda2 + sdd2 -> form VolGroup00 with md2 /dev/md2 -> 18 GB -> sdb1 + sde1 -> form VolGroup00 with md1 sda,sdd -> 36 GB 10k SCSI HDDs sdb,sde -> 18 GB 10k SCSI HDDs I have added 2 36 GB 10K SCSI drives in it, they are detected as sdc and sdf. What should I do if I

Hi, I'm currently experimenting with software RAID1 on a spare PC with two 40 GB hard disks. Normally, on a desktop PC with only one hard disk, I have a very simple partitioning scheme like this : /dev/hda1 80 MB /boot ext2 /dev/hda2 1 GB swap /dev/hda3 39 GB / ext3 Here's what I'd like to do. Partition a second hard disk (say, /dev/hdb) with three

I installed Centos 6.x 64 bit with the minimal ISO and used two disks in RAID 1 array. Filesystem Size Used Avail Use% Mounted on /dev/md2 97G 918M 91G 1% / tmpfs 16G 0 16G 0% /dev/shm /dev/md1 485M 54M 407M 12% /boot /dev/md3 3.4T 198M 3.2T 1% /vz Personalities : [raid1] md1 : active raid1 sda1[0] sdb1[1] 511936 blocks super 1.0

Hi all, As part of my raid experience, I have yet to have to do this, but was wondering how you guys would attempt it. I have 3 drives in a raid 1, with one as a hot spare. They are 250gb with all space used by two raid devices, 1 with boot, the other with LVMs filling them up. Now, lets say down the road I want to put in 500gb drives and replace them....yikes. I was thinking of taking out the

Something seems to be wrong with my file systems, and I want to fsck everything. But I cannot. The setup consists of 2 hds, carrying 3 raid1 (ext3) file systems (boot, /, swap). OS is up-to-date CentOS 5. So I boot from CentOS 5.3 dvd in rescue mode, do not mount the file systems, and try to run fsck -y /dev/md0 fsck -y /dev/md1 fsck -y /dev/md2 For each try I get an error message:

Hi I have a Raid 1 centos 4.4 setup and now have this /proc/mdstat output: [root at server admin]# cat /proc/mdstat Personalities : [raid1] md2 : active raid1 hdc2[1] hda2[0] 1052160 blocks [2/2] [UU] md1 : active raid1 hda3[0] 77023552 blocks [2/1] [U_] md0 : active raid1 hdc1[1] hda1[0] 104320 blocks [2/2] [UU] What happens with md1 ? My dmesg output is: [root at

I think I have solved my issue and would like some input from anyone who has done this for pitfalls, errors, or if I am just wrong. Centos 5.x, software raid, 250gb drives. 2 drives in mirror, one spare. All same size. 2 devices in the mirror, one boot (about 100MB), one that fills the rest of disk and contains LVM partitions. I was thinking of taking out the spare and adding a 500gb drive. I

Hi all, Please excuse the many posts. Wondering if any one can help me with the the setup. I have 2x2TBdisks. I would like to mirror them. I would like to create two LVMs so that I can snap shot from one to the other. During Centos 6 install, how would I go about this as its confusing? So far I am here; 1) Created the following raid devices; md0 500MB (use it for /boot) md1 4000MB (use it

Hi list, I'm new with UEFI and GPT. For several years I've used MBR partition table. I've installed my system on software raid1 (mdadm) using md0(sda1,sdb1) for swap, md1(sda2, sdb2) for /, md2 (sda3,sdb3) for /home. From several how-to concerning raid1 installation, I must put each partition on a different md devices. I've asked times ago if it's more correct create the

Hello all, I have 2 x 250GB sata disks (sda and sdb). # fdisk -l /dev/sda Disk /dev/sda: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 14939 119997486 fd Linux raid autodetect /dev/sda2 14940 29878

Hey folks, I don't seem to be able to get a response from the openfiler forums (and they want 40 quid for the fine manual!), and since there has been a lot of chat about it here lately, I figured I'd ask here. Please forgive my terminology as I am just making my first baby steps into iSCSI and Fiber Channel, and am not very well read on the matters. So I could be using the wrong terms

Is it possible or will there be any problems with using mdraid on top of mdraid? specifically say mdraid 1/5 on top of mdraid multipath. e.g. 4 storage machines exporting iSCSI targets via two different physical network switches then use multipath to create md block devices then use mdraid on these md block devices The purpose being the storage array surviving a physical network switch

[root at alan centos]# du -sh 5.* 19G 5.3 14G 5.4 -- ?Don't eat anything you've ever seen advertised on TV? - Michael Pollan, author of "In Defense of Food"

On 04/23/2022 09:19 PM, H wrote: > On 04/19/2022 09:57 AM, Roberto Ragusa wrote: >> On 4/18/22 1:27 PM, H wrote: >>> I have a new computer with 2 x 2TB SSDs where I wanted to install C7 and use mdadm for RAID1 configuration and encrypting the /home partition. On the net I found https://tuxfixer.com/centos-7-installation-with-lvm-raid-1-mirroring/ which I adopted slightly with

I am running software RAID1 on a somewhat critical server. Today I noticed one drive is giving errors. Good thing I had RAID. I planned on upgrading this server in next month or so. Just wandering if there was an easy way to fix this to avoid rushing the upgrade? Having a single drive is slowing down reads as well, I think. Thanks. Feb 7 15:28:28 server smartd[2980]: Device: /dev/sdb