similar to: Request for hpacucli output from people running HP Smart Array controllers

On a CentOS 6 64bit system, I added a couple prototype SAS SSDs on a HP P411 raid controller (I believe this is a rebranded LSI megaraid with HP firmware) and am trying to format them for best random IO performance with something like postgresql. so, I used the raid command tool to build a raid0 with 2 SAS SSDs # hpacucli ctrl slot=1 logicaldrive 3 show detail Smart Array P410 in Slot 1

Hi, is there a way to rebuild an array using ssacli with a P410? A failed disk has been replaced and now the array is not rebuilding like it should: Array A (SATA, Unused Space: 1 MB) logicaldrive 1 (14.55 TB, RAID 1+0, Ready for Rebuild) physicaldrive 1I:0:1 (port 1I:box 0:bay 1, SATA HDD, 4 TB, OK) physicaldrive 1I:0:2 (port 1I:box 0:bay 2, SATA HDD, 4 TB, OK)

Jason Warr wrote: > On July 10, 2015 11:47:09 AM CDT, m.roth at 5-cent.us wrote: >> Hi. Anyone working with these things? I've got a drive in "predictive >> failure" on in a RAID5. Now here's the thing: there was an issue >> yesterday when I got in, and I wound up power cycling the RAID; >> first boot of attached server had issues, and said the

Hi. Anyone working with these things? I've got a drive in "predictive failure" on in a RAID5. Now here's the thing: there was an issue yesterday when I got in, and I wound up power cycling the RAID; first boot of attached server had issues, and said the controller had a failure, and a drive had failed, and wouldn't continue booting; when I gave it the three-finger salute,

Not so much...and hpacucli is actively user hostile. I finally connected and woke up the box (and who, in their right minds, puts the power on button on a rackmount RAID box in the *back* of the box?), and I'm trying to create one large RAID 6. But... ctrl slot=3 show config is incredibly bizarre. It shows me my physical drives... but starts at 9, and for everything up to 18, shows two of the

I had to install C5 on a dev server for various reasons (legacy system support and so forth). This dev server is a HP DL180 G6, with a SmartArray P410 raid card... I've installed hpacucli via the RPM from HP's site, but its not finding the controller... C5 (64 bit) is using the default CCISS drivers for this card. # hpacucli ctrl all show config Error: No controllers detected.

On 10/07/15 10:06, John R Pierce wrote: > On 10/7/2015 8:42 AM, m.roth at 5-cent.us wrote: >> Got an old HP box with a P800 Smart Array controller. The HP RAID >> box >> plugged into it's failing, and we got a new JetStor. Anyone know if we >> can just plug the JetStor in and set it to passthrough, or if we have >> to use the P800's firmware to set up

On 10/07/15 11:13, m.roth at 5-cent.us wrote: > Jack Bailey wrote: > >>> controller that expects to talk to individual SAS or SATA drives. you >>> can manage it with hpssacli from centos. >> I have the P822. It has no JBOD or RAID 0. hpacucli works with CentOS >> 7.0, but is broken on 7.1 -- it cannot find the controller. > Can it do RAID 6? > This page

Greetings: HP has drivers for the this controler but how do you get the drivers working for the install on Centos 4.0 ? Integrated Dual Channel Ultra ATA 100 IDE Adapter (ATA Models) I extracted the files from this RPM and placed on a CD. hpacucli-7.21-17.linux.rpm boot with the driver disk option and it does not find drivers. I'm I on the right track? Thanks -Jay

The hpacucli works... but what isn't clear to me, even with googling, is whether I have to do something from the utility, or whether I can just pull the failed drive out of the hot-swap bay and put another in. I *do* see that I have to re-enable the drive, or rescan it, but right now, I'm concerned about just pulling the dead one out. mark

Jack Bailey wrote: > On 10/07/15 10:06, John R Pierce wrote: >> On 10/7/2015 8:42 AM, m.roth at 5-cent.us wrote: >>> Got an old HP box with a P800 Smart Array controller. The HP RAID box >>> plugged into it's failing, and we got a new JetStor. Anyone know if we >>> can just plug the JetStor in and set it to passthrough, or if we have >>> to use the

On 10/7/2015 11:47 AM, Jack Bailey wrote: > On 10/07/15 11:13, m.roth at 5-cent.us wrote: >> Jack Bailey wrote: >> >>>> controller that expects to talk to individual SAS or SATA drives. you >>>> can manage it with hpssacli from centos. >>> I have the P822. It has no JBOD or RAID 0. hpacucli works with CentOS >>> 7.0, but is broken on 7.1

Hello I'm running CentOS 5.3 with httpd-2.2.3-22.el5.centos.x86_64 and php-5.1.6-23.2.el5_3.x86_64. When the logrotate scripts run and send the HUP signal to httpd, the httpd process quits instead of reloading. The only thing I can find in the logs is this: [Sun Apr 19 04:02:04 2009] [notice] seg fault or similar nasty error detected in the parent process There wasn't any segfault

Hello all, I am a complete newbie to OpenSolaris, and must to setup a ZFS NAS. I do have linux experience, but have never used ZFS. I have tried to install OpenSolaris Developer 134 on a 11TB HW RAID-5 virtual disk, but after the installation I can only use one 2TB disk, and I cannot partition the rest. I realize that maximum partition size is 2TB, but I guess the rest must be usable. For

Hi list, who can say does FreeBSD 8.x/9.x support HP Smart Array B120i controller? Thanks, Serguey.

Hello, I'm trying to boot a HP Proliant DL320 G5 with a HP Smart Array E200i RAID card (latest BIOS and latest RAID card firmware). With menu.c32 or vesamenu.c32 from syslinux 3.50 the system hangs Booting from local disk... PXE-M0F Exiting With the latest dev version (3.52-pre) it hangs with : vesamenu.c32: attempted DOS system call The issue has already been reported but

Hello, I'm trying to install CentOS 6.0 64bit on a HP ProLiant ML110 G7 with a HP Smart Array B110i SATA RAID Controller. One logical drive (RAID 1+0) on the RAID Controller is already build. CentOS Installation can't find the logical Drive, but it shows me the zwo physical drives (sda+sdb). After searching the web, I found following hints:

Hi I am trying to install CentOS 5.6 on HP DL 180 G6 which has HP Smart Array B110i SATA RAID Controller Driver. I have 4 * 500 GB SATA HDD and configured RAID 1+0 using System BIOS, the BIOS detects usable disk space as 940GB disk space, when i start installing the OS, it does not detect HP Smart Array B110i SATA RAID Controller Driver As per

Hi, I recently took delivery of a bunch of HP BL25p blades to add to my collection. I am attempting to install Centos4 x86_64 using PXE - the initial PXE DHCP stuff works, and the kernel and initrd are downloaded, but the server then immediately clears the screen and displays: "1706-Smart Array Controller Extended BIOS Data Area Memory Corrupted Array Controller Interrupt 14h BIOS Cannot

Hello I have samba installed on my server, with a fileshare. When connecting to samba, using windows, filesnames with " (double quotes) in them become gibberish on the windows client. Under linux I connect to these fileshares using NFS, and the names are correct (I also created them this way). I've made a screenshot: http://users.webmind.be/~glenn/samba.PNG How can I fix this?