similar to: Supermicro Adaptec AIC-9410 HostRAID controller

I have a server with Super Micro X7DB3 motherboard and Adaptech AIC-9410 controller (http://www.supermicro.com/products/motherboard/Xeon1333/5000P/X7DB3.cfm). The hard disk is single SeaGate SAS disk (300Gb). I'd like to install CentOS 7 on the server, but unfortunately, the CentOS installer can't find any hard disk. I think the problem maybe caused by the disk controller. Can you please

I'm trying to get the RHEL-5 version of their kernel driver to install with no luck so far. http://www.adaptec.com/en-US/support/scsi/u320/ASC-39320A-R/ Here is what I'm seeing when I install their provided .RPM: [root at hcnas ~]# rpm -i a320raid.rhel5.i686.rpm Adaptec adp94xx driver installer - V1.2.5934.0-1 Backing up all modified files to /boot/adp94xx-backup-4 Using GRUB

The latest adp94xx chipset is now available on some SuperMicro motherboards. I was wondering has tried the driver with CentOS 4.2? Any thoughts on the driver performance? Does SMART work? Etc. Thanks, Mark Hoy

Hello, I just recently purchased two new Supermicro servers: SYS-6025B-3R SYS-6015B-3R Both of these have an Adaptec AIC-9410 SAS controller in them, that is apparently not detected (or supported?) by FreeBSD (amd64) (7.0 or 7.1 RC1) Is there any way to get FreeBSD to detect this controller (and drives on it)? I found some conversations from 2006 about this, but no updates since. Thanks in

Good Day! We have some troubles with installation of CentOS 5.0 on Supermicro server with Adaptec AIC-9410 SAS Controller, but installation complete successfully on CentOS 4.5. This issue has been solved in version 5.2? Or it will be solved in version 5.3? Sorry for my English ;( -- wbr - Maxim Odinintsev

I'm having speed problems with the SCSI card we're using to do tape backup. It seems to be functioning in 16 bit mode and the current thinking is that perhaps it's using a legacy driver instead of the correct one. The Adaptec site has a 'driver' for RHEL5 which I've downloaded and tried to install but it seems to have a problem installing on a CentOS-5 system. [root at

Hi All, I need to install CentOS 4.0 x86_64 using Adaptec ASC-29320A with HostRAID enabled, but it seems my card isn't recognized. I've tried to install the hardware using driver downloaded for RHEL 4.0 from the Adaptec Website, but still it's unrecognized. P.S. I'm able to install RedHat 9.0 using this card before. Is there anyone have any solution for this? Thanks and

Hi, I want to compile the kernel for supermicro server . I need the SATA controller support(adp94xx.o). Where i can get the source code of linux kernel 2.6.9 with the support of above mentioned driver ?? Thanks in advance Regards juliet

<style> body {color:#000000;font-size: 9pt;font-family: ±¼¸²,Arial} table {color:#000000;font-size: 9pt;font-family:±¼¸²,Arial } a:link {color:#000000;text-decoration: none} a:visited {color:#000000;text-decoration: none} a:active {color:#000000;text-decoration: none} a:hover {color:#000000;text-decoration: none} p

Hi: I've tried to install centos 4.3 in a raid array, setuped on bios as mode "Adaptec". The chip is ICH7R but centos always sees 2 drives instead of the array that I create. I've contacted Supermicro support and they gave me this link ftp://ftp.supermicro.com/driver/SATA/Adaptec_ICH7R/Linux/Redhat/ , but the disk drivers I tried to use with centos 4.3 did not work, saying that

An INTEL Server motherboard model SE7501BR2 with an onboard Adaptec AIC7901 controller (with HostRAID) is not being recognized by CENTOS 4. The AIC79xx driver loads correctly, however it does not "see" the fact that I used the HostRAID onboard software to create a RAID 1 set. I went to the INTEL site and only found a driver for RHEL 3.0 and I was unable to find a driver on the adaptec

Trying to install on IBM eseries with Adaptec 9405 SAS. Fail to install / recognized SAS. Download from IBM RHE4 driver ... unfortunately did not help. Anybody have any idea? -- ----------- ( ) ?( (.) (.) )? ---o000o-(_)-o000o--- Mahayudin Mohd Hashim Kuantan Port Consortium Sdn Bhd Wisma KPC, KM 25 Tanjung Gelang PO Box 199 25720 Kuantan, PAHANG MALAYSIA Vox :

--> Requote: Trying to install Centos 4.3 on IBM eseries with Adaptec 9405 SAS. Fail to install / recognized SAS. Download from IBM RHE4 driver unfortunately did not help. Then I install RHEL 4 / SLES 9 - Running fine. SAS was installed and recognized. Anybody have any idea? -- ----------- ( ) ?( (.) (.) )? ---o000o-(_)-o000o--- Mahayudin Mohd Hashim

Hi I have a problem with a production server (Acer Altos G5350) SLE9 SP3 with Samba 3.0.20b-3.4). It provides shares for about 15 Windows workstations. I purchased it with an Adaptec Hostraid a320 controller (using two 146mb Seatgate drives mirrored with Hostraid) but slowly realising that getting up tod ate kernel supported drivers for these cards is near impossible. When I installed SLE9 it

Hi people I am new to Xen and having some trouble getting it up and running. I am trying to install it on a Dell Poweredge SC420 that has CentOS (RHEL3 clone) installed. The error that I am getting when I first try to boot into the Xen kernel, after having installed the binary and adding the necessary lines to grub.conf is : ---snip--- md: Autodetecting RAID arrays md: autorun ... md: ...

We are strategizing a set of backup servers and I have been trying to deduce wha the maximum size of each RAID 5 array should be to match the OS we are using. We are currently running CentOS 4.3 64 bit. We have planned a 2 TB RAID 5 array for testing but we will need to set up several larger ones for production. I have poked around and I see people mention limits like 2TB max file size and 32TB

Can anyone confirm the adaptec 2005s working, and working WELL for them under any 2.4 kernel? Thanks, Gabe

Hello, is anybody using this controller with opensolaris/snv ? http://www.adaptec.com/de-DE/products/Controllers/Hardware/sas/entry/SAS-2405/ does it run out of the box ? how does it perform with zfs? (especially when using it for zfs/nfs esx setup) the driver from adaptec is for solaris 10 u4. If it does not work out of the box, can i use that driver with opensolaris/snv ? thanks roland --

Hello I'm running centos 3 and a raid 5 array running in good order however I'm trying to install some monitoring for the raid array using dptapps-static-3.1.24-1.i386.rpm and run it but this fails: [root at ns1 Scripts]# /usr/dpt/raidutil -L physical osdIOrequest : File /dev/dpti17 Could Not Be Opened Engine connect failed: COMPATIBILITY number Has anyone a rpm for a supermicro

I've recently purchased an Adaptec SNAP server to serve as a central file server for a 2500 machine, 7000 user network. My goal is for this server to serve as a backend file store to a number of other servers that the client machines will communicate with. In particular, I would like to have my current file server (which runs samba 3.0.10 in kernel 2.6.10-gentoo-r6) mount a share on the