similar to: wan hdlc_ppp and IPv6

Hello, I contacted Krzysztof Halasa, the maintainer of the current sethdlc code. This is the response he gave me. Of course, I have this working now. Still some minor configuration to do, but It does work, and the connections to the internet are _much_ faster than when I went through the adtran... I would highly recommend to anyone with a fractionated T1, with data and voice channels to

All, I am trying to configure hdlc support on T100P Digium card - everything seems ok... but it just does not work at all. I was able to compile all drivers, the light on the card becomes green when I plug T1 link.... but I even can't ping default router IP... there is no data coming back to me, so I am confused completely now. Also I tried both protocols - raw hdlc and cisco hdlc. The

Hello, I am experiencing what may be a unique problem with operating the bridge. My hardware is custom Freescale MPC875 processor based with one ethernet (eth0) and one hdlc (hdlc0) WAN port and I am connecting two of these boards together using the WAN ports over a long distance - essentially two bridges in series. They are running Linux 2.6.15 with bridging enabled in the kernel

Pavel, you may be interested in my work on Cisco HDLC bridging: http://marc.theaimsgroup.com/?l=linux-netdev&m=108802311131855&w=2 I have used it with the bridge driver (in 2.4) without any problems (yet ;)), and I am sure Krzysztof Halasa, the HDLC maintainer, would be thrilled if you managed to port it to a recent version of the kernel and make it a compile-time option. Oh, it also

Scratch that last comment. The kernel code I have now is identical to what I posted. Sorry for the misinformation. > -----Original Message----- > From: bridge-bounces@lists.osdl.org > [mailto:bridge-bounces@lists.osdl.org] On Behalf Of Eble, Dan > Sent: Tuesday, June 29, 2004 12:57 PM > To: 'arkady-parabel@ngs.ru' > Cc: bridge@osdl.org > Subject: RE: [Bridge] Re:

Good day everyone, Hope someone can help me with a spandsp/app_rxfax problem. I've compiled spandsp 0.0.2pre26, and app_rxfax.c from soft-switch.org Both went just fine, and i've checked my libtiff and libxml (along with the devel-s) versions - they're fine. Machine is fedora core 3, x86_64. Asterisk is 1.2.17, zaptel 1.2.15 Dialing in on a zap channel. T1 PRI, esf,b8zs TE110P

Hello, Is anyone successfully using spandsp 0.0.2pre25 with either asterisk 1.0.x or 1.2.4? I've built a Gentoo ebuild for this version of spandsp and app_rtxfax, and it builds, but I'm not having any luck getting it working. 99% of my test faxes fail. Reverting to 0.0.2pre20 yields a much higher success rate. I've bumped the console debugging level in logger.conf to include debug

Guys, I have been a trying to send a fax using spandsp/app_rtxfax/asterisk. I'm trying to send a (3 page) fax, and all I'm receiving is a single blank page (and I've tried it with 2 fax machines). As some background, I'm using asterisk with an E1 connection through a Sangoma WAN card -- all of this has been working with voice for over 6 months. The software is all working too

Guys, [Forgive this repost -- my original posting doesn't seem to have shown up in the list (yet)] I have been trying to send a fax using spandsp/app_rtxfax/asterisk. I'm trying to send a (3 page) fax, and all I'm receiving is a single blank page (and I've tried it with 2 fax machines). As some background, I'm using asterisk with an E1 connection through a Sangoma WAN card

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hello list, We're currently facing some issues concerning T.38 gateway faxing. This is a device used almost exclusively for receiving faxes. Calls are incoming to asterisk on a SIP trunk (sangoma netborder) using G711A. Gateway mode is activated in the asterisk dialplan towards a Cisco SPA 112 running firmware 1.3.5. We are using asterisk 1.8.13.0 with the T.38 gateway patch applied (I know I

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

fact I'm surprised that's changed (FreePBX's DAHDI module created the current config -- i.e. the one I posted in my original email). I'll change that back and see if that makes a difference, but I'm pretty sure I used the above configuration in a previous attempt with the same results. Also, I have indeed received the following messages prior to the interface going down and

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

I just upgraded my asterisk install from january 2005 CVS HEAD to current CVS HEAD : * zaptel * libpri * asterisk My asterisk have one TE405P with one span (the clock source) pluged into a telco PRI E1, a second span is a PRI E1 to another PBX and the third one is a T1 to a rhino channel bank. Everything went smoothly except that the two PRI span restart every ten seconds after some HDLC

Hello Team I have installed the new DL580 and used the new TE420B to add capacity on our ivr. Before I put new E1?s I decided to first move the old e1 from the old system to this new one but it has errors which not only affect the audio quality, but also cause the asterisk to refuse any call after sometime even though the channels seems up and active {seems d-channel fails}.. When processing

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hello, I have spandsp working with asterisk (tested on one PSTN fax machine). Today someone wanted to send me a fax, but there was a problem with the TIFF file. This is what asterisk console says: TIFFReadDirectory: /var/spool/asterisk/fax/1140608321.7.tif: cannot handle zero number of strips. MissingRequired: /var/spool/asterisk/fax/1140608321.7.tif: TIFF directory is missing required

my target is to produce a linux router with T100p to Fract T1 24chan to ethernet and TDM 4channel FXO. I have not been able to get nethdlc to work, just get zaptel networking not configured if I set bchan and dchan the card comes to life, but I don't believe this is correct for what I want to accomplish. according to markster@ this is the way they do it. using (multiple distro versions

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]