similar to: Fwd: P5GC SATA mode problem

Hi, I'm puzzled by an ASUS P5GC-MX/1333 with a WD320AAJS disk. My 5.2 DVD refused to see the hard disk. As the CD happened to have a bad MD5 sum, I assumed this was due to a bad burnt image. Backed off to 5.1. Installation of 5.1 to /dev/sda went OK, then I upgraded by yum to 5.2. But, at the next boot, the new kernel can't see the disk. Only when BIOS IDE Setup is "compatible"

i'm attempting to rebuild centos51 kernel-xen. (fwiw, because pciback has NOT been compiled into the kernel, http://bugs.centos.org/view.php?id=2767) after, yum install kernel-devel kernel-xen-devel and usual, ln -s /usr/src/kernels/`uname -r`-`uname -m` /usr/src/linux cd /usr/src/linux cp /boot/config-`uname -r` ./.config make oldconfig make menuconfig ... next, make rpm

I am going into: /usr/src/kernels/2.6.18-92.1.10.el5-x86_64 and doing a "make mrproper" attempting to rebuild the Modules.symvers file. As I added ALSA 1.0.17 to the current kernel. I am getting an error: make mrproper scripts/Makefile.clean:17: /usr/src/kernels/2.6.18-92.1.10.el5-x86_64/drivers/infiniband/hw/amso1100/Makefile: No such file or directory make[3]: *** No rule to

I have a Tyan S3870 (K855A) motherboard which I would like to perform a burn in test with. lm_sensors needs a kernel module compiled to be support this motherboard's sensors. The instructions, for compiling the module, by tyan (ftp://ftp.tyan.com/software/lms/3870.sensors.conf) match closely with the instructions I found here (http://www.howtoforge.com/kernel_compilation_centos). I

On Wed, Aug 13, 2008 at 3:07 PM, Eduardo Grosclaude <eduardo.grosclaude at gmail.com> wrote: > OK, this is probably long, and your answer will surely make me slap my > forehead really hard... please help me understand what goes on. <autoslap>Ouch!</autoslap> Sure /boot/grub/grub.conf still needs editing... That's why you really, really WANT both partition tables to be

... is on SourceForge: http://tcng.sourceforge.net/dist/tcng-10b.tar.gz md5sum d28bc6b1ed8973814213942288ab5d18 See also http://tcng.sourceforge.net/ This release fixes a few compatibility problems with internationalization and with kernels using strange version names. Also, the "mtu" parameter of TBF is now optional. The complete list of changes is below. - Werner

Hello, I've just signed up to offer some of my time to the project as suggested by Ernesto Celis on CentOS Spanish users' list. I'd like to help translate the project's wiki pages to Spanish. I'll be happy to receive some suggestions as to what would be my first assignment. Cheers to you all and the biggest THANK YOU! -- Eduardo Grosclaude Universidad Nacional del Comahue

Hello, I have just finished my Spanish translation of the last Newsletter. As I have no edit rights to the proper zone, I have written it into my own personal page http://wiki.centos.org/EduardoGrosclaude. Please some elder member of the familiy snip it off from there and hang it where it belongs. :) I have not involved myself in prior proofreading, so this may be a bit off. May I slip in a small

Hello, Should Xen still work on CentOS 5.2 with 1GB RAM? On my Toshiba Satellite notebook Xen performed reasonably well as of CentOS 5.0. After I updated the system, Xen takes an unusable startup time. Every task at boot, since nash is fired, seems to take increasingly longer. I can't seem to find any references to this problem. Where should I look first? Thanks in advance -- Eduardo

I need to serialize computing job requests for two different multicore machines, and in some near future, for a cluster. I have worked with SGE but it requires NFS and other administrative steps, plus it seems a bit overkill for my needs. I guess some simpler queue managing engine may have been developed, possibly over SSH. Any pointers? TIA. -- Eduardo Grosclaude Universidad Nacional del

Has anyone succesfully compiled a PAPI+perfctr-enabled kernel? I've been mixing and matching instructions from the PAPI distribution and those from CentOS wiki to no avail. TIA -- Eduardo Grosclaude Universidad Nacional del Comahue Neuquen, Argentina

I'm intending to do some version control, hence looking for some plugins. Geany and geany-plugins packages in Rpmforge seem to be out of sync: Name : geany-plugins Arch : i386 Version : 0.18 Release : 1.el5.rf Name : geany Arch : i386 Version : 0.19.1 Release : 1.el5.rf When both are installed, geany claims that plugins are not

------Original Message------ From: centos-request at centos.org Sender: centos-bounces at centos.org To: centos at centos.org ReplyTo: centos at centos.org Subject: CentOS Digest, Vol 71, Issue 28 Sent: Dec 28, 2010 12:00 PM Send CentOS mailing list submissions to centos at centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos or,

Hello, Please. Can the following spec give me some headache with CentOS 4.4? Where to find out? I have read former advice on the list about not to mess with Intel PCI extra cards. Thank you in advance CPU P4 3,06 (524) S.775 FSB533 INTEL D101GGCL 775 ATI DDR SV R 1 PCIE 16X D.CORE Mem KINGSTON DDR2 1GB 533 HD SATA 80GB SEAGATE ST380211AS /or/ HD SATA 120GB SEAGATE ST3120026AS --

Hello, When it comes to translations, it would be useful to have the original sources. Is there any place for us translators to pick up a copy? We do not have edit access to originals. TIA -- Eduardo Grosclaude Universidad Nacional del Comahue Neuquen, Argentina

Hello, is anybody using DBMail or any other approach to manage huge volume mail installations? Comments about it? Are RPMs somewhere out there? -- Eduardo Grosclaude Universidad Nacional del Comahue Neuquen, Argentina -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20060203/ee7851b3/attachment-0002.html>

Hello, I have this cheap network card which insists on me compiling its own sundance.ko module every time I update my kernel release. I had the poor idea to leave nightly yum service enabled on this remote server, only to find my network was gone at the following reboot. Had to go there, figure out that kernel stuff is carefully avoided by up2date, but not so by yum service, and rebuild. Compiling

Hello, I want to compare CentOS to Fedora and other distros on a stability/network-dependance basis. Where should I look for some published statistics on updates? I mean probably megabytes per week (or whichever units, of published updates over time), per distro. Thank you in advance -- Eduardo Grosclaude Universidad Nacional del Comahue Neuquen, Argentina -------------- next part --------------

I have this cheap "ENCORE 10/100Mbps Fast Ethernet PCI Adapter" which comes with its own driver that compiles to 'sundance.ko' and performs bad (30% packet loss) on a fully updated CentOS 4.4 box. This brand, model and driver have worked OK for me on some other CentOS installations, none of which are 4.4. Short of replacing the board, which you can bet I will do, can anybody

Out of the blue, dmesg on my HP Proliant w/ a SCSI disk gives loads of messages like this one: EXT3-fs error (device dm-0) in start_transaction: Journal has aborted Then the root fs goes read-only, so little else can be done on the machine. LVM locks up. At restart, fs needs a reboot to recover after fsck. The host starts up ok, then I am given some more minutes before the problem reappears.