similar to: SNMP and OID/MIB/MRTG

I got itchy fingers over the weekend and decided to fix what wasn't broken and upgraded one of the older servers from Centos 5.2 to Centos 5.3. Following the recommended process of updating glibc and such before the rest, it appeared to work perfectly and rebooted without problem. However, MRTG 2.15.2 started complaining about unexpected values. I installed/updated both MRTG (2.16.2) and

Hi I''ve patched net-mrtg http://www.net-snmp.org/ with http://x-ray.prokon.cz/data/snmp/ sucefully Also I''ve copied QOS.TXT to /usr/local/share/snmp/mibs when I make a normal use of snmp, with mrtg in order to monitor all traffic on eth0 and eth1, it works OK. But, how must I do in order to get monitor for a specific class ? If I make a snmpwalk (like README suggest), I get

i''ve installed mrtg to make graphics of the trafic from the interfece throw the snmpd, and the same with ipac witch put iptables accounting rules colect them and store, and gets the output, but the "problem" is that ipac graphics are 3 times smaller that the snmpd. Why??? i did catch all the trafic with ipac so no problem here, and i know that ipac/iptables is at level 3, and

Hello. Is there any command in the shorewall script that prints how many or the hits the last 5 min? /Rickard Eriksson

I check system load like so: [root at server cron.daily]# w 10:07:33 up 4 days, 15:01, 2 users, load average: 4.22, 3.17, 3.09 I would like to to graph the 3.17 5 minute average with MRTG. Anyone know of some examples of doing this?

Hi guys I'm trying to set up the SNMP service. I need it to use MRTG to graph some variables of my Centos 5.3 box. Any of you have a working SNMP configuration can send me to tweak mine? Thanks David -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20090730/ab36b8c3/attachment-0002.html>

Hello Centos People, I have a CentOS 5.3 box that had a total of 5 ethernet cards in it. It functions to share an internet connection with 4 different subnets. All works fine, except I'm noticing that my MRTG traffic graphs are wrong. Further digging with snmpwalk reveal that the order of the ethernet interfaces changes every time the machine is rebooted to a different order. For

OpenBSD 5.6 nut-2.7.2 (bin package) Liebert IntelliSlot Unity Card IS-UNITY-DP ups.conf: ...... ? mibs = ietf ? snmp_version = v1 ...... The problem is that the card responds to other snmp (v1,2c,3) requests normally but not to the 1.3.6.1.2.1.33.1.1.1.0 (UPS-MIB.upsIdentManufacturer). # snmp-ups -a laes2ups -DDDDDDD Network UPS Tools - Generic SNMP UPS driver 0.72 (2.7.2) ?? 0.000000???? debug

Hi all, I hope someone can help me with this one. I'm trying to graph all traffic on the localhost's network card with Cacti. >From what I understand I should use SNMP to query the traffic, but I can't seem to get SNMP info for the network interface. I have installed all the necessary snmp tools, "yum install snmpd net-snmp net-snmp-utils net-snmp-devel net-snmpt-libs "

Hi I''m trying to move the tracking of the shaping from MRTG to Cacti. My predecessor, who built all this stuff and was far more advanced than I, had a shell script that collected data by running tc -s qdisc show dev on both eth 0 and 1 and then pushing it out via snmp to another server running MRTG. I''m building a new server with cacti and having trouble with the custom

I want to check some client OpenVPN TUN interfaces with MRTG running at my VPN server, so I have to specify their OID interface numbers in mrtg.cfg. The problem is, these numbers are dynamic, as they may change whenever OpenVPN restarts for any reason... so, how can I write stanzas such as Target[somehostvpninterface] : ifInOctets.X&ifOutOctets.X:public@ <SOMEHOST.IP> without wiring up

I just used Nick Mae's well written HOWTO on setting up Cacti on CentOS 4.xto setup Cacti on my CentOS 5.1 system : http://wiki.centos.org/HowTos/Cacti_on_CentOS_4.x I was hoping to add a page or section for CentOS 5.x with the modifications I'm including below. My wiki.centos.org username is "GeneWood" Changes : # Make sure snmpd accepts 'public' as public

Hello We have Dell servers and need to monitor them through SNMP. but need to install or insert Dell MIBs to our Centos. is copying MIBs are enough ? has any one is using Dell OpenManage on Centos ? Thanks

Hi, i'm running CentOS 6.0 on my server and installed mrtg from the rpm-package mrtg-2.16.2 . I also installed the depending packages perl-IO-Socket-INET6 perl-Socket6 .... mrtg works fine with IPV4-Addresses. When i specify a Target by IPV6-Address (or hostname resolving to a V6-address) mrtg fails. Here i have a small sample-config for V4 which is working: LogDir: /tmp ThreshDir: /tmp

any help/tips/document/link to setup and configure MRTG under Centos. Thanks

I'm trying to get MRTG up and running on CentOS, but the displayed http page says that I don't have permission to access /mrtg/ on the server. Here are my commands yum install mrtg vim /etc/httpd/conf.d/mrtg.conf /etc/init.d/httpd restart cfgmaker --global 'WorkDir: /var/www/mrtg' --global 'Options[_]: bits,growright' --output /etc/mrtg/mrtg.cfg public at 10.200.200.1

Hi, I`m trying to use the agent snmp buit in the asterisk-1.4, but I can`t do this... I used this link to do it: http://www.voipphreak.ca/archives/382 but I can't... Does somebody know how to do this or knows a how-to to do this?? Thank's _______________________________________________________ Yahoo! Mail - Sempre a melhor op??o para voc?! Experimente j? e veja as

Has anyone written any MRTG scripts for monitoring domain CPU usage? It''s probably pretty simple to do, but there''s not much point re-inventing the wheel. Thanks James _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I have created shell script for MRTG statistics of droped/rejected packets: ftp://slovakia.shorewall.net/mirror/shorewall/mrtg/ http://slovakia.shorewall.net/pub/shorewall/mrtg/ rsync://slovakia.shorewall.net/shorewall/mrtg/ example: http://slovakia.shorewall.net/pub/shorewall/mrtg/example/ It is not based on /var/log/messages (syslog), but iptables counter. A lot of packets are droped/rejected

Does anyone know if the 3.8 update will fix the long-standing problem with snmp interface counters on 64 bit machines? I think it was mentioned in the RH notes, but they said that a year ago too... (The problem is that the 32 bit counters don't wrap correctly so mrtg/cacti graphs go crazy after 2 gigs of data have gone by). -- Les Mikesell lesmikesell at gmail.com