similar to: Support older Cyberpower models

Hello, I'm a new to NUT and I'm having some setup problems. Here's my setup: Nut 2.0.2 Gentoo Linux 2.6.13-r3 CyberPower AVR900 According to the hardware compatibility guide this setup should work. Here's what I get: root@gentoo (0) [552] % upsdrvctl start Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2)

Hi, guys. I have a new CyberPower PR2200 which I'm trying to control using NUT. It has a serial port and I'm connected serially. I am using the cyberpower driver and before a power failure it seems to mostly be working: jeff@backup:~$ upsc cyberpower@localhost battery.charge: 000 driver.name: cyberpower driver.parameter.port: /dev/ttyS0 driver.version: 2.0.4 driver.version.internal: 1.00

I did a bunch of work on this today. It should be all set to go. This patch is to add support for the Cyberpower RMCARD snmp cards. I basically copied the driver for bestpower, changed the name and updated the mib map. I have this running on two separate systems (two separate ups's) and it looks good. The only thing I could not figure out was updating the Makefile.am (my aclocal/libtools

Is anyone working on anything to support the Cyberpower CP550SL/AE550 Serial? Any idea if it uses the same or similar protocol as the other Cyberpower models? I have an HP 4952A Serial Protocol Analyzer and a Cyberpower CP550SL. Once I get the CP550SL up and working in Windows over RS232 I'll hook up the 4952A and see whats going on. I'm not sure what it uses for default baud rate.

Hi, I've installed Nut 2.0.5 on a RedHat 9 box. I have a GeekSquad 1500 UPS. (GeekSquad is a BestBuy brand) I've found out that it's actually a CyberPower 1500 AVR LCD. I'm using it with the serial cable. I'm unable to get it working with any of the drivers provided with NUT. I've tried cpsups, cyberpower and powerpanel. here's the output of the different drivers

This unit works fine with the "cyberpower" driver (which reports it as "Unknown model - 15"). It reads this much from it: battery.charge : 100 driver.name : cyberpower driver.parameter.pollinterval : 2 driver.parameter.port : /dev/ttyS0 driver.version : 2.2.0- driver.version.internal : 1.00 input.frequency : 60.2 input.voltage : 121 ups.firmware : 5.100

Arjen, I read the following in the upgrade notes and just wanted to see what the status was for the cyberpower driver? The note reads: - The cpsups and nitram drivers have been replaced by the powerpanel driver, and removed from the tree. The cyberpower driver may suffer the same in the future. What does this mean to me -- a cyberpower user? -- David C. Rankin, J.D.,P.E. Rankin Law

I'm looking for people that are using the 'cyberpower' driver that has been available for some years now. It seems the overhauled 'powerpanel' driver could support your UPS too. The commands and status bytes used are identical, the only difference being the way the values read for battery charge, temperature and frequency are interpreted. If we can find a way to detect when to

I'm looking for people that are using the 'cyberpower' driver that has been available for some years now. It seems the overhauled 'powerpanel' driver could support your UPS too. The commands and status bytes used are identical, the only difference being the way the values read for battery charge, temperature and frequency are interpreted. If we can find a way to detect when to

Hello! I got my hands on a CyberPower 1500AVRT, and i'm trying to get it connected to my Gentoo machine. I've followed all the basic guides on setting up NUT and UPS' but have had no luck. My current ups.conf is: [cyberpower-gentoo] driver = cyberpower port = /dev/ttyS0 desc = Workstation Upon running /etc/init.d/upsd start or upsdrv start I get: * Starting

I recently purchased a CyberPower CP1200AVR UPS and am trying to get NUT 2.0.3 or NUT 2.1.0 to work with the newhidups driver, but am having little success. Before I purchased I did some googling and saw people talking about problems so I'm guessing it may not be supported yet? I did find some posts about people getting it to (sort of) work with some hacks, but couldn't tell if they

CyberPower Systems PR6000LCDRTXL5U http://www.cyberpowersystems.com/products/ups-systems/smart-app-ups/pp-series/PR6000LCDRTXL5U.html I had to create the following udev rule (on RHEL6): ATTR{idVendor}=="0764", ATTR{idProduct}=="0601", MODE="664", GROUP="dialout" Shutdown testing successful. UPS comes back online after turning off. # upsc battery.charge:

I am having some problems getting NUT to run with my cyberpower avr1200 (brandnew). I have a straight through serial cable, and I am getting this: /usr/local/etc/rc.d/nut.sh start Starting nut. Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2) Giving up on hardware detection after 3 tries Unable to get initial hardware info string Driver failed

I am having some problems getting NUT to run with my cyberpower avr1200 (brandnew). I have a straight through serial cable, and I am getting this: /usr/local/etc/rc.d/nut.sh start Starting nut. Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2) Giving up on hardware detection after 3 tries Unable to get initial hardware info string Driver failed

Hi, I wanted to report some success with monitoring this UPS, a "Geek Squad" brand GS-700U that I purchased earlier this year from Best Buy Canada. Information about this... thing is very scarce so here is what I know: The unit itself is probably made by Cyberpower. It has a 9-pin serial port on the UPS, as well as a serial-USB adapter thing. I cracked open the serial-USB

root at Monitor:/etc/nut# upsc ups1 Init SSL without certificate database battery.runtime: 133200.00 battery.runtime.elapsed: 0.00 device.mfr: CYBERPOWER device.model: PR2200LCDRT2U device.serial: 1 device.type: ups driver.name: snmp-ups driver.parameter.pollfreq: 1 driver.parameter.pollinterval: 2 driver.parameter.port: 192.168.1.7 driver.parameter.snmp_version: v1 driver.version:

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

Hello, I have a CyberPower CP1500PFCLCD and I'm trying to get nut to see it under OpenIndiana. All search online suggested that it basically can't happen, but I decided to ask again, maybe things have changed since then. The UPS can be seen by the system: # /usr/sbin/cfgadm -lv usb9/1.1 Ap_Id Receptacle Occupant Condition Information When Type

This code, added to drivers/genericups.h, supports the CyberPower SL series UPSes. I've tested with my 725SL - the online/on battery transition, and low battery status, and finally the shutdown signal all work as expected. *** genericups.h.orig Sun Nov 2 16:54:24 2003 --- genericups.h Mon Oct 3 13:49:00 2005 *************** *** 220,225 **** --- 220,234 ---- TIOCM_ST