similar to: REGRESSION: New "megatec" driver does't work for UPS that was managed by old fentonups driver

Hi again, I tested several times using the Megatec driver from nut 2.2.2 to no avail, as it definitely never "sees" the UPS. Always getting : # drivers/megatec -DDD -a Alpha Network UPS Tools 2.2.2 - Megatec protocol driver 1.5.14 [megatec] Carlos Rodrigues (c) 2003-2008 debug level is '3' Starting UPS detection process... Asking for UPS status [Q1]... Q1 => FAILED

Hi there, I've replaced yesterday my old UPS with a brand new "Eaton Ellipse MAX 600 USBS". I've choosed the Eaton (previously MGE) both because I've always been extremely satisfied with MGE UPSes of all kinds at work, and because of the involvement of MGE (with Arnaud) in nut development, which made me quite sure that I would have no trouble with an Eaton (MGE) UPS and

Hi, FYI, I started receiving spam to the email address I use only for this mailing-list, about one week after I posted a couple messages onto it. So the nut mailing-list is definitely used by spammers for email addresses harvesting :-( -- Michel Bouissou <michel at bouissou.net> OpenPGP ID 0xEB04D09C

Hi list here is the patch to make fentonups recognize some PowerCOM's UPS's, and to setup terminal lines for them (at least for SMK-1500a) as powercom's original upsmon do. fentonups -x powercom works correctly with SMK-1500a (it screamed ''Communications with UPS lost - check cabling' or 'Short read during UPS id sequence' without this patch). Sorry for

Hi Patrick, 2006/4/2, Patrick Beard <p.beard@blueyonder.co.uk>: > Hi Arnaud, > > Just wanted to let you know the the Belkin F6H500ukUNV is working for me > with the fentonups driver. > > http://catalog.belkin.com/IWCatSectionView.process?IWAction=Load&Merchant_Id=&Section_Id=202840 > > I originally tried it with the genericups driver with upstype=7 but this

Hi Henning, you should get in touch with Carlos, who his developing a generic megatec driver (available from svn: http://eu1.networkupstools.org/source.html) Arnaud -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://people.debian.org/~aquette/ OpenSource Developer -

Hi ups-devel, As I looked throw www.networkupstools.org site, haven't found any pointers where to send patches, so I hope this is the right place. (Please let me know weather this is the right place.) The patch contains a minor change in the logic of the driver, our Effekta MHD 3000 UPS continuously writes status data to the serial port, so one has to send a CR character and empty the

Hi Marek, thanks for your report, forwarded to the dev list, and logged in the patch tracker: https://alioth.debian.org/tracker/index.php?func=detail&aid=303209&group_id=30602&atid=411544 thanks to also post back the ID string inside double quote to validate the exact string (use my present gmail address if you don't want to subscribe to upsdev). Arnaud -- Linux / Unix Expert -

Hi Stefanos, you should mail to the NUT list, and try the megatec driver, which is only available from subversion for the moment (but should be included in the next stable release). Carlos might give you some help with this driver. Arnaud Quette -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Carlos, Today I was browsing through the NUT Tracker and noticed an entry which linked to a message on nut-upsdev: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-January/000559.html Although the fentonups driver is no longer in the tree (since it was replaced by the megatec driver), I think there is still some merit in this patch. Notice the following lines from this message: >

good new first: the megatec driverin 2.0.5 now works with the Online Xanto S3000R here - well, for the very basics. the UPS has NO way ofidentifying itself. It also does not respond to the power ratings query ("F"). I previously used a hacked up fentonups driver. This means the driver cannot figure out the battery voltage and thus no battery charge level, which is a problem in our

Hi, I am working on a patch for FENTON.H to support some more ups models, I wonder if someone can help with further information,meaning and importance for the following values that are beeing set in the model capability table: float lowvolt; float voltrange; float chrglow; float chrgrange; int lowxfer; int lownorm; int highnorm; int highxfer; Thanks, Nadav

On 1/23/07, Henning Brauer <hb-nut@bsws.de> wrote: > good new first: the megatec driverin 2.0.5 now works with the Online > Xanto S3000R here - well, for the very basics. > > the UPS has NO way ofidentifying itself. It also does not respond to > the power ratings query ("F"). I previously used a hacked up fentonups > driver. This means the driver cannot figure out

I had some free time this weekend, and made some long overdue changes to "megatec". The thing is, these changes lead to a couple of questions that I must ask before I go on and "svn commit" them: 1) The blazer, fentonups, esupssmart, ippon, sms and mustek drivers are now completely covered and all of their functionality should now be present in megatec, and also every model

Do you know some piece of code I could look at to see learn more about this ?

Do you know some piece of code I could look at to see learn more about this ?

>> I tested it by pulling the supply to the ups. It got the 'on and then >> the 'low battery' upsmon then shutdown my system. The ups however >> remained on. >the ups shutoff (hardware ups shutdown) seems not to be working. >Carlos might have more ideas on the cause... This might not be a bug - it could be that I reconnected the supply to soon. I say this

After trying the 'powermust' driver I can confirm it works well with the F6H500ukUNV ups from Belkin. I reported my tests but by accident posted them directly to Carlos and not the mailing list (sorry Carlos). Anyway brief summary of the powermust driver with the F6H500ukUNV; Detects Online state. Reports the Battery charge correctly. Detects On Battery State. Detects Low Battery State.

Hello, i`m looking for a nut-compatible low-power UPS (need to hook a home-server+dsl equipment with a load of ~50W to that) which should be as energy efficient as possible and be also affordable. i currently have an older powerwalker which constantly burns ~15W for nothing. The transformer inside getting that hot that you don`t like to touch it and i think 15W out of 50 is a little bit high

Hi again, The PGP sig for 2.2.2 is missing from http://eu1.networkupstools.org/source/2.2/ (so the corresponding link from the download page is broken). Also, for the record, I'm trying to compile 2.2.2 from sources and so far, on my Ubuntu Hardy system : - If I don't use during configure "--without-snmp", compilation crashes talking about some undefined things. - If I use