similar to: Belkin F6C100-UNV + newhidups

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID:

Greetings all; I pulled a Belkin F6C100-4 into the shop this afternoon, deader than a door nail. Out of service for about a year because (I'm assuming here) that the cooling fan stopped and cooked what little remaining life there may have been out of the batteries, which had swelled so badly I had to split its frame to get them out. They are also in the under 1 volt per 12 volt pack

I just moved my UPS over from serial to USB and found that I needed to add it to the hotplug USB list to make things work. Belkin F6C120-UNV - Bus 002 Device 004: ID 050d:0912 Belkin Components It seems to be working OK on 2.0.4 with newhidups. Attached is a patch which I think should add the appropriate device id's in the right places to the trunk code. Jon -------------- next part

I recently installed NUT 2.2.1 and set it up with a Belkin F6C100-UNV. I can monitor it via serial (belkinunv) or USB (usbhid-ups) cable, and both do seem to work fine, but I would prefer USB to avoid having to add a PCI serial card to the machine. I had to unplug something else to try it with a serial cable. Using 'belkinunv', there's a "-x wait" option: [ from

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Zaid, I have a Belkin F6C800-UNV which has both a serial and USB connector. The serial connection is already working with the Belkinunv driver. I will connect via the USB and then compare both sets of variables. This should allow me to correlate and shed some light on the meaning of many of Belkin's non-standard "Usage" descriptors. With this information, it should be very easy

hi i have a belkin ups here some setting chmod 0600 /dev/hiddev0 chown nut:root /dev/hiddev0 linux:/home/sonia # /usr/lib/ups/driver/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools: New USB/HID UPS driver 0.28 (2.0.4) No matching USB/HID UPS found Driver failed to start (exit status=1) linux:/home/sonia # /usr/lib/ups/driver/upsdrvctl -u root start

Have had no issue until I ran apt-get dist-upgrade this morning: # /lib/nut/newhidups -u nut -DDDDDD auto Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 (2.0.5) debug level is '6' Checking device (0000/0000) (001/001) - VendorID: 0000 - ProductID: 0000 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 001 Trying to match device Device does not

Hi, I've been fighting with trying to get a Belkin Universal model F6C800-UNV to work with NUT. The error I am getting is as follows: ---------------------------------------------- * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Belkin 'Universal UPS' driver 0.06 (2.0.0) tcgetattr(/dev/ups): Inappropriate ioctl for device Driver failed

I have checked in a cleaned-up version of patch #302111 (Belkin support) into CVS. See cvs diff -uN -r before_PSE_2 -r after_PSE_2 to check the difference. Here is the CHANGES entry: Tue Sep 13 20:50:14 UTC 2005 / Peter Selinger <selinger@users.sourceforge.net> - newhidups: added Belkin support. Also added some new variables and instant commands (some of these were already used by

Hi, I got a Belkin F6C550-AVR UPS today and was trying to get it working with NUT, I used the "hidups" driver and got some data out of it, mainly the following: battery.charge: 100 battery.runtime: 120 driver.name: hidups driver.parameter.port: /dev/usb/hiddev0 driver.version: 2.0.0 ups.mfr: Unknown ups.model: Unknown ups.serial: Unknown ups.status: OL the versions of NUT that I tried

Hi, I got a Belkin F6C550-AVR UPS today and was trying to get it working with NUT, I used the "hidups" driver and got some data out of it, mainly the following: battery.charge: 100 battery.runtime: 120 driver.name: hidups driver.parameter.port: /dev/usb/hiddev0 driver.version: 2.0.0 ups.mfr: Unknown ups.model: Unknown ups.serial: Unknown ups.status: OL the versions of NUT that I tried

Hi Peter, I got all your patches and applied them, and I wanted to say kudos for a great job done. This is the output of upsc that I'm getting right now. I had the same issue when using any cvs version (from two weeks ago) that made my UPS go into a state where it wasn't functioning normally (checking the kernel log shows that it cannot be connected and I had around a page of DEVFS_USB

Hello, all, I had been using NUT's Ubuntu package (64 bit) with no problems until upgrading to Ubuntu 11.04. Now, I get the following message when I try usbhid-ups: $ sudo /lib/nut/usbhid-ups -a mybelkin Network UPS Tools - Generic HID driver 0.35 (2.6.0) USB communication driver 0.31 Can't claim USB device [050d:1100]: could not detach kernel driver from interface 0: Operation not

I have changed over to CentOS5 on some of our computers. I had been using Mandriva 2006 and the nut software worked using: driver = newhidups port = auto Using the same version of nut with the same config files on CentOS5, I get the following error output from 'upsdrvctl': Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools: New USB/HID UPS driver 0.28 (2.0.4) No

I have changed over to CentOS5 on some of our computers. I had been using Mandriva 2006 and the nut software worked using: driver = newhidups port = auto Using the same version of nut with the same config files on CentOS5, I get the following error output from 'upsdrvctl': Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools: New USB/HID UPS driver 0.28 (2.0.4) No

I ran into the following issue today and would like some feedback from the group. Setup: I am using a MGE Pulsar Evolution 2200 UPS connected through a Belkin (F5U218-MOB) 4-Port USB Hub. Scenario: The newhidups subdriver_matcher function calls belkin_subdriver->belkin_claim. The belkin_claim function in belkin-hid.c matches the VendorID of the hub to Belkin's VendorID (0x050d), causing

Bus 003 Device 002: ID 050d:1100 Belkin Components # /lib/nut/usbhid-ups -a belkin Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 (2.2.0-) No matching HID UPS found Hmm best to stick with 2.0.4. Justin.

Bus 003 Device 002: ID 050d:1100 Belkin Components # /lib/nut/usbhid-ups -a belkin Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 (2.2.0-) No matching HID UPS found Hmm best to stick with 2.0.4. Justin.