similar to: newhidups... at last.

Hi everybody, If we let the feature running, it appears that the driver gets unbound after a while ( variable from quarter of hour to 6 hours ) and cannot reconnect. This behavior appear with both MGE Ellipse ASR and non-ASR models with connection to an UHCI and OHCI controllers. The USB core is from 2.4.28 kernel. We use nut-2.0.3. Start, powerfail and recovery detections, UPS shutdown work

Hello everybody, After succeeded in "tuning" nut-2.0.0's hidups and 2.0.3's newhidups on customized Linux kernels, we are now facing a new challenge : trying to install nut-2.0.5 on a RedHat ES4 which is based on a 2.6.9 kernel. I picked up the 2.0.5 source package and follow the INSTALL doc until step 6. So far so good. RH ES4 is managed by udev, therefore I presume we

Ok, I installed the ups, and installed nut, and /proc/bus/usb/devices says this T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 0.01 S: Manufacturer=POWERWARE S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00

i can't seem to get newhidups to detect my UPS.. i'm using nut-2.0.3 (tried both the rpm from fc5-updates and compiling my own) here is the entry for the UPS in /proc/bus/usb/devices T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0764 ProdID=0501 Rev= 0.01 S: Manufacturer=CPS S: Product=UPS

Hi, I'm trying to get a Powerware 3105 UPS working on SuSE 10.0. I have compiled nut from the current Subversion repository. This UPS uses the bcmxcp_usb driver. I cannot get the driver to find the ups on the USB bus. The error message I get is:- -------------- bcmxcp_usb -u nut -DDDDD -a pw3105 -------------------- Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) debug level is

Folks, I'm fairly new to this whole Linux UPS thingie, but I'd quite like to have a look at getting my UPS to work under Linux and would be grateful for any help in getting a driver. I have a reasonable working knowledge of Linux and software development, and thus am happy to modify config files, alter kernel settings, etc, although I'm no C guru. I have a Kebo UPS-650D, which

Hi all, I just downloaded, built and installed nut-2.0.4-pre2. I have an APC Smart ups 3000 connected via a usb cable. I have compiled and installed the usb drivers. I installed the libhidups and libhid.usermap per the README. I have the following ups.conf: [APC-3000-ups] driver = newhidups port = auto desc = "APC smart 3000" When I try to start the driver I get the

I have a Belkin F6H500ukUNV ups that I am attempting to get working under nut, however it does not appear to be detected by nut, I'm assuming that I need to feed some information back to you guys to get it included in the database somwhere. I've included (what I can think might be) the relivant outputs. Please let me know if you require anything else. dmesg output /sbin/newhidsups

I have a MGE Evolution 3000 connected via USB to a linux server (HP Proliant G3). The server is running kernel 2.4.30 and nut-2.0.3. But before nut trying to connect to the UPS, I guess HID doesn't work as long as I get a message like this in dmesg: -------------------------------------------------- usb.c: new device strings: Mfr=4, Product=136, SerialNumber=50 usb.c: USB device number 2

--zhXaljGHf11kAtnf Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Content-Transfer-Encoding: quoted-printable I'm trying to set up a TrippLite Internet Office 750 just like this guy: http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-June/000007.html Here's the output of a few interesting commands stuart@tyro:~+ dpkg-query -l nut nut-usb| tail -n2| awk

*********************** Your mail has been scanned by InterScan MSS. *********************** Has anyone managed to get this UPS to work? I am using the laster development nuts. My /proc/bus/usb/devices content: ==== cut ==== T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=ffff ProdID=0000 Rev= 1.00 S:

Hi Does there exist any work on getting the powerware driver to work with USB devices under freebsd? I have tryed with the usb enabled newhidups driver for freebsd but it does not seem to work. $ newhidups -a newhid -DD Network UPS Tools: New USB/HID UPS driver 0.23 (2.0.2) debug level is '2' found 0 (-1) No USB/HID UPS found //erlis -------------- next part -------------- An HTML

Hi Friends, I have an Excalibur 4GB USB Pen Drive Model Number EXC4. I think it is getting detected by the Centos but I am not sure about the mount point or the device point it is taking /dev/s?? Logs from /var/log/messages. Mar 11 11:30:06 l_l_box kernel: usb 1-1: USB disconnect, address 3 Mar 11 11:30:22 l_l_box kernel: usb 1-1: new high speed USB device using address 4 Mar 11 11:30:22

Hi I am running FC5 with nut coming from the fc5 extras repositories. I am trying to configure a Gamatronic D-Compact ups. The cable that came with the ups has a serial connector on one end and a usb on the other. cat /proc/bus/usb/devices produces T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P:

I am having this problem where out of the blue my mouse and UPS will stop functiong. Once this even occurs I will find multiple messages like: Jan 15 10:40:32 nureyev kernel: drivers/usb/input/hid-core.c: control queue full Jan 15 10:40:42 nureyev kernel: drivers/usb/input/hid-core.c: control queue full iin /var/log/messages. The only way I can get the mouse and UPS back is to ssh into the

i just purchased a tripp lite OMNIVS1500XL and have been attempting to get it working with the usb drivers since it doesn't have a serial port. it hasn't been anywhere near successful and i was hoping someone might be able to point me in the right direction. i run gentoo and this is what i currenlty have installed: nut 2.0.2 libusb 0.1.10a (gentoo modified) usbutils 0.11-r5

Howdy nut-users :) Got a problem with nut detecting my UPS. Here's my scenario. Base platform is a HP ML350 G6. UPS is an APC Smart-UPS 1000. Base OS is VMware ESXi 5.0 with all current patches. I've created a virtual machine using the VMWare supplied VMA. USB passthrough is configured to pass the UPS through to the VMA. So I essentially have a SLES 11 (x86_64) server with a USB

Hello, i have this strange problem with APC BackUPS RS 1500 ? older one model, white one under windows in powerchute is device OK, working everything ok selftest ok, just ordinary ups. under CentOS 7 minimal (CentOS-7-x86_64-Minimal-1708.iso) kernel version 3.10.0-693.el7.x68_64 driver version 2.7.2 i have this strange probem: nut driver didnt start automatically with error, after i enter in

Hello, i have this strange problem with APC BackUPS RS 1500 ? older one model, white one under windows in powerchute is device OK, working everything ok selftest ok, just ordinary ups. under CentOS 7 minimal (CentOS-7-x86_64-Minimal-1708.iso) kernel version 3.10.0-693.el7.x68_64 driver version 2.7.2 i have this strange probem: nut driver didnt start automatically with error, after i enter in

I used a brazilian UPS from "TS-Shara" which uses the megatec serial protocol and it works perfectly. Now I have another one from the same brand (TS-Shara) and it uses a USB cable. I found the following: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0483 ProdID=0035 Rev= 2.00 S: