similar to: driver error

Hello. I've got a quartet of IBM x3630 M3 with one that is frequently hard locking under heavy NFS load. I am running 9.0-RELEASE with all the patches from freebsd-update. My problem machine has 8 16 core clients, each doing IO intensive tasks connected to it via a Procurve and the onboard igb0 interface. Mostly network reads, typically 10MB read per MB written. When the machine locks

Hi guys - OpenSSH sftp (on solaris) >From man page Termination on error can be suppressed on a command by command basis by prefixing the command with a `-' character (for example, -rm /tmp/blah* ). This does not seem to work - instead the server seems to fail to recognize the command from the batchfile. Consider this batchfile mkdir tmp cd tmp put rpt.list bye We want to

Charles, maybe we are getting closer :-) > The tripplite_serial_protocol branch has some debug statements that will show up if you run "sudo drivers/tripplite -D -a name-of-ups" from the nut directory. Network UPS Tools - Tripp-Lite SmartUPS driver 0.91 (2.7.4-432-gafd90f5a) ?? 0.000000??? [D1] debug level is '1' ?? 0.177766??? [D1] W value = 0x86 ?? 0.177782??? [D1] L

Hi I have a Dell PowerEdge T310 *tower* server.. I have to buy an ups by apc... anyone could help me giving an hint ? a simple "smart ups 1000" could be enough ? thx so much!! lewis.

WOW! OK! The light bulb above my head just came on. I added the script to the Subnet Up Script section, and now all the routes I need have been added in to the table for me. I did have to modify the line a little since I'm using pfSense (FreeBSD). I changed it to... route add "$SUBNET" -iface "$INTERFACE" ...I also used... route del "$SUBNET" -iface

Hey! I was wondering if anybody has had any luck getting a Tripp Lite UPS with the SNMPWEBCARD working with NUT? I haven?t been able to get it working using the same steps I did getting an APC unit working. I have been able to get snmpwalk to work with SNMP 1 so theoretically it should work for at least that snmp v1. We are using Centos 6.4 with NUT version nut-2.6.5-2.el6.src.rpm. We currently

Hi, I seem to have a problem with compiling the kernel 2.4.13 on redhat 7.2? It would compile fine but have errors about ext3 support on reboot. I download ext3-2.4-0.9.13-2413.gz to my linux machine to enable it be useful with ext3 support but when I try to gunzip it with the instructions gunzip < ~/ext3-2.4-0.9.13-2413.gz | patch -p1 i get gunzip: stdin: not in gzip format I get an

Hello everybody, I got tree UPS devices connected to a Debian server, and i am searching for a way to configure them. The server power-cord is only connected to one of the ups devices, and should monitor the other ups systems to sent email status. I got a HP R3000XR UPS with has a RS232 communication port that I have working perfectly. Then I have two APC SmartUPS 750V devices that are

Hey everyone, My company is beginning to look at using SSD drives in our CentOS based servers. Does C5 and C6 support TRIM and other "required" functions for the SSD to operate? Thanks, Andrew Reis Microsoft Certified Technology Specialist CompTIA Network+ Networking/Systems Analyst Webmaster DBMS Inc.

2009/5/3 Thomas Juerges > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi Arnaud, > Hi Thomas, > I just checked the 2.4.1 version of nut and found that you forgot to add > my old UPS model (APC Smart-UPS 900). I guess it is because you were > busy at the time when I sent you the patch. So here it goes again. :) > uh, right sorry. I was pretty sure I applied

> >> Maybe it's not a standard ethernet-to-UPS cable? > > That's Ben's point - either it is actual Ethernet (usually found on an add-on UPS SNMP monitoring card, where the jack typically has two status LEDs, one on either side of the notch for the modular plug tab) that needs to go to another Ethernet jack on a NIC or a switch, or it is a proprietary APC cable that

G'day y'all, Here's a tiny patch set for drivers/apcsmart.c and drivers/apcsmart.h. Adds APC SmartUPS 1250 ("8QD" case) + 940-0024C recognition to apcsmart. (Unpatched apcsmart.c v1.99.8 misidentifies the SmartUPS 1250 as a "dumb" UPS.) For NUT 2.0.5+. NUT 2.0.5: Patches apply successfully. Builds successfully. Works as expected under Ubuntu 7.04. NUT 2.2:

I have no problems lauching asterisk from the command line . . . asterisk -vvvvc However, I'm trying to autostart on boot up, so I'm trying safe_asterisk When I do this, I get: Asterisk ended with exit status 127. Asterisk died with code 127. Aborting. I've looked through the script but can't find what the problem is. I'm running on RedHat Fedora. Thanks for your help.

Ok, so another apc UPS 3000 complained about bad batteries, and I changed them out from the same order that I'd gotten in a couple of months ago. The APC SmartUPS 3000 started connecting and disconnecting the USB connection. I brought down and up the service, no joy. Finally, after googling, I found a *completely* undocumented way to start apcupsd, that a few years ago someone was told to

I need direction. I don't know what to google for anymore. I am unable to get my SmartUPS 2200XL to be recognized. My suspicions are that it's UDEV or Kernel related. I've updated the kernel to the highest version I feel comfortable with due to other things that run on the server, and I've updated UDEV a bit too. When I plug in the USB cable from the UPS into the server, I

Is it possible to connect networks with different masks together? For example a 10.26.0.0/16 subnet with a 192.168.117.0/24 subnet. See this thread for more details... https://forum.netgate.com/topic/134218/tinc-initial-setup

On 12/26/18 8:55 AM, Charles Lepple wrote: > On Dec 25, 2018, at 4:07 AM, David Melik wrote: >> Lately I got (used) an APC Back UPS Pro 1000 and Back UPS NS 1080. I got an [8P8C]-to-USB cable from another UPS, but the Pro isn't detected (with usbhid-ups.) I haven't tried the NS yet but it seems to not be on the list though looks just like the Pro. >> > There are a few

maybe i have solved this issue, i unplugged APC BackUPS from USB 2.0 and PLUGGED INTO USB 3.0 and now it works prefectly at first time without any side effects, strange, this shoud be working since USB 1.0 so ups driver is configured OK, this config works ok for backups, this looks like there is no problem with detection of UPS but with USB driver or something around so simply if somebody has

I'm trying to setup a server controlling 8 ups, 6 APC Smartups 1500 and two 1000. Because of the number of ups, i connected them using usb cables. I'm using Debian Etch AMD64 and nut 2.2.0 from testing (already tried 2.0 from stable, but had problems reading the ups serials and all the following problems of 2.2). This is my ups.conf: [ups2] driver = usbhid-ups port =

Hi, I am trying to compile the kernel with ext3 support and i downloaded the 2.4.13 kernel and patched it for RH 7.2 to update from the 2.4.7 precompiled ext3fs kernel. Then i selected ext3 support and and the JBD debugging support under 'make xconfig.' Then i ran the following commands make clean make dep make bzImage make modules make modules_install cp arch/i386/boot/bzImage