similar to: Tripplite Smart1200LCD and Debian

These patches allow this device to function in nut.. diff --git a/trunk/drivers/tripplite-hid.c b/new/drivers/tripplite-hid.c index c36da98..dddd13c 100644 --- a/trunk/drivers/tripplite-hid.c +++ b/new/drivers/tripplite-hid.c @@ -71,6 +71,8 @@ static usb_device_id_t tripplite_usb_device_table[] = { { USB_DEVICE(TRIPPLITE_VENDORID, 0x2005), battery_scale_0dot1 }, /* e.g. TrippLite

Hello Charles, Thank you for your suggestion, however it didn't help. I was running it as root but I went ahead and added the -u root anyways. Nothing changed. So part or all the problem is that I don't have the "libhidups or libhid.usermap" files that the man page talks about: You also need to install manually the legacy hotplug files (libhidups and libhid.usermap,

Hi, I've been trying to get my new Tripplite OmniVS100 UPS (USB Connection) to work on my system. What I have is: Ubuntu 10.04 Server Nut 2.4.3 /etc/nut/ups.conf [omni] Driver = tripplite_usb Port = auto Desc = "My Server" /etc/nut/nut.conf MODE=standalone Iget the following error when using the > sudo upsdrvctl start Network

Hello, I tried to the the driver 'usbhid-ups' for my Tripplite UPS Model: INTERNET350U. I received the following error: Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 This TrippLite device (09ae:2010) is not (or perhaps not yet) supported by usbhid-ups. Please make sure you have an up-to-date version

I'm read through the archives trying to figure out how to get a Tripplite SmartPro SLT 1500 configured with NUT using the USB interface (it also has a serial interface but I'd rather not). The thread which this link belonged to seemed most instructive: http://lists.alioth.debian.org/pipermail/nut-upsdev/2007-January/001656.html and I followed it as best I could. I'm running a

Hi Charles and Jonathan, I am going through my over 300 unread NUT messages, and I just discovered this one from mid-December. At the time, I was trying to clean up the tripplite subdriver of newhidups, but never got the information I needed. I have enabled this driver now, but it is marked "experimental". The driver is still incomplete, in the sense that there are many unmapped device

> > > 2.117586 send_cmd(msg_len=2, type='G') > > 3.219418 libusb_get_interrupt: Connection timed out > > 3.219474 libusb_get_interrupt() returned 0 instead of 8 while > sending 3a 47 b8 0d 00 00 00 00 '.G......' > > 4.219593 libusb_get_interrupt: Connection timed out > > 4.219661 libusb_get_interrupt() returned

At the company I work for, we are using many TrippLite OMNI900LCD UPSs and are having difficulty setting the lower transfer threshold voltage. On our other model, the Eaton MGE-3S550, this can be set using upsrw to set the input.transfer.lowsetting, but on the Omni900, this option is not available. In our testing, it defaults to ~95v but we want to set it to 84v. More info: - OS = OpenSuse 13.1 -

Hi Everyone, I'm having trouble getting TrippLite SMX1500LCDT to work on FreeBSD 11.2, nut 2.7.4 installed from FreeBSD port. The debug output is rather big when I'm starting usbhid-ups initially, Please find that attached (gzipped to comply with message size limit). Subsequently, until I unplug and replug the USB cable, I'm geting a shorter debug output, like this: Network UPS

Hello, I am try to get my "new" UPS running with NUT on my OpenMediaVault device but only receive error meassages on several configurations I try. Your support is really appreciated for getting it solved. Best Regards, Olaf *lsusb* Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID

On Jun 13, 2014, at 4:45 PM, Bossard wrote: > No matching HID UPS found > > > Driver failed to start (exit status=1) > > > So I tried 'usbhid-ups -x productid=2010' and received the same error. Same exact error? I suspect it's a permissions error the second time. Add "-u root" to the command line - since this was not a known VendorID:ProductID pair

Hi, I'm running the latest stable nut (2.4.3). It doesn't appear to provide support for the Tripp Lite SmartOnline SU1000XLA. [sups] driver = usbhid-ups port = auto vendorid = 09ae productid = 4004 4337# upsdrvctl start Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 Using subdriver:

Hi, I'm running the latest version of NUT and with the above UPS and I keep getting the following error: "tripplite_usb[3308]: Error reading B value: Device detached? (error 0: could not claim interface 0: Device or resource busy)" The device keeps disconnecting and re-connecting until fails. I've tried to see if others are getting this - but I could not locate a

Back in July I succeeded in getting my SMART1500SLT to work with help from folks on the list and changes someone made in subversion. I just checked out the latest code from subversion and it stopped working after a reboot. It looks like usbhid-ups won't load now: # usbhid-ups -a tripplite Network UPS Tools: 0.29 USB communication driver - core 0.34 (2.3.0-1555) No matching HID UPS found

I have been having a few issues recently. I'm running Nut 2.4.3 on Solaris 10 (10/09) using a TrippLite SMART700DVa UPS. Everything seems to be working fine except for some random issues. During a power cycle (UPS online to offline to online) NUT will occasionally get disconnected from the UPS. A call to it using upsc results in "Error: Data stale". And running dmesg has the

--zhXaljGHf11kAtnf Content-Type: text/plain; charset=us-ascii Content-Disposition: inline Content-Transfer-Encoding: quoted-printable I'm trying to set up a TrippLite Internet Office 750 just like this guy: http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-June/000007.html Here's the output of a few interesting commands stuart@tyro:~+ dpkg-query -l nut nut-usb| tail -n2| awk

I am currently running FreeNAS-8.3.1-RELEASE-x64 (r13452) using the packaged version of NUT, 2.6.5, using the usbhid-ups (Generic HID driver 0.37). Here is the output of "/usr/local/libexec/nut/usbhid-ups -D -D -D -D -D -D -a tripplite": Network UPS Tools - Generic HID driver 0.37 (2.6.5) USB communication driver 0.31 0.000000 send_to_all: SETINFO driver.parameter.port

Device manufacturer and name: Tripp-Lite OmniSmart500 upsc output: matt at backup:/etc$ sudo upsc tripplite battery.charge: 100 battery.test.status: Battery OK battery.voltage: 14.56 battery.voltage.nominal: 12 device.mfr: Tripp Lite device.model: OMNISMART500 device.type: ups driver.name: tripplite_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3

Hello All, This is my first post to the list & I have tried to do as much searching and debugging on my own as I can bear. Please HELP! I am currently using up to date Centos 5.2 32-bit - kernel version: 2.6.18-92.1.10.el5PAE #1 SMP. I am using a Tripplite OMNIVS1500 via usb connection. I am using the tripplite_usb driver. I have tried to user versions 2.2.0 from an rpm, 2.2.2 & and the

Hello All, This is my first post to the list & I have tried to do as much searching and debugging on my own as I can bear. Please HELP! I am currently using up to date Centos 5.2 32-bit - kernel version: 2.6.18-92.1.10.el5PAE #1 SMP. I am using a Tripplite OMNIVS1500 via usb connection. I am using the tripplite_usb driver. I have tried to user versions 2.2.0 from an rpm, 2.2.2 & and the