similar to: Belkin F6C1200-UNV on Ubuntu 11.04

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID:

Mr. Selinger, I'm CCing you directly since it appears (insofar as I can tell) that you are one of the delelopers for the newhidups driver. This is the third time I've submitted this (hence the CC this time). Hopefully mailman takes it. I've tweaked my SPF records, and I'm hoping that was the problem. My sincere apologies if this has gone through and I just haven't seen it

I just moved my UPS over from serial to USB and found that I needed to add it to the hotplug USB list to make things work. Belkin F6C120-UNV - Bus 002 Device 004: ID 050d:0912 Belkin Components It seems to be working OK on 2.0.4 with newhidups. Attached is a patch which I think should add the appropriate device id's in the right places to the trunk code. Jon -------------- next part

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hello, I noticed a strange thing when attempting to upgrade a specific package (lavaan) from c2d4u and wondered if someone could confirm the problem. In short, apt seems to think that an older version from the "universe" repo is higher than the newer version from c2d4u. When I do apt-cache showpkg r-cran-lavaan I get the output at the bottom of this email. Then, I tried to force

I recently installed NUT 2.2.1 and set it up with a Belkin F6C100-UNV. I can monitor it via serial (belkinunv) or USB (usbhid-ups) cable, and both do seem to work fine, but I would prefer USB to avoid having to add a PCI serial card to the machine. I had to unplug something else to try it with a serial cable. Using 'belkinunv', there's a "-x wait" option: [ from

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

Hi, I've been fighting with trying to get a Belkin Universal model F6C800-UNV to work with NUT. The error I am getting is as follows: ---------------------------------------------- * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Belkin 'Universal UPS' driver 0.06 (2.0.0) tcgetattr(/dev/ups): Inappropriate ioctl for device Driver failed

Oh oops, I see you already did. -- Peter selinger wrote: > > You could send it without "submitting" it. That's the advantage of > patches - they can be discussed. There are lots of eyeballs here that > might see what's wrong. Thanks, -- Peter > > Eric S. Raymond wrote: > > > > Peter Selinger <selinger at mathstat.dal.ca>: > > > I

This model is available in AU/NZ and can work as USB or serial. It uses the cutdown Bulldog software that comes with the cheaper serial based belkin models, and they don't officially support the USB mode under Linux. Anyone managed to get this working with NUT using either serial or USB? I'd really like to get the extra functionality of the NUT tools vs the very simple setup of the

I just bought a pair of Belkin USB UPSes -- F6C1200-UNV and F6C550-AVR -- and installed the latest version of nut under Ubuntu 7.04. I'm using the F6C1200-UNV. My system does see the device; dmesg says [ 82.718428] usb 2-2: new low speed USB device using ohci_hcd and address 2 [ 82.941189] usb 2-2: configuration #1 chosen from 1 choice [ 83.036825] usbcore: registered new driver

I just bought a pair of Belkin USB UPSes -- F6C1200-UNV and F6C550-AVR -- and installed the latest version of nut under Ubuntu 7.04. I'm using the F6C1200-UNV. My system does see the device; dmesg says [ 82.718428] usb 2-2: new low speed USB device using ohci_hcd and address 2 [ 82.941189] usb 2-2: configuration #1 chosen from 1 choice [ 83.036825] usbcore: registered new driver

Greetings! Thanks to all the developers who have made this project so far. Searching for a Linux based Belkin UPS monitor led me straight to the Network UPS Tools. I have bought a Belkin F6C900-UNV (900VA) for use on a Slackware 10.2 server to replace an older APC model that died suddenly. So far I have successfully managed to get NUT 2.0.5 compiled and configured and found that this Belkin

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

I recently upgraded from nut-2.4.1 to 2.4.3 and my UPS stopped working. usbhid-ups now fails two communicate with the UPS: With 2.4.1: # /sbin/usbhid-ups -D -a auto Network UPS Tools - Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 debug level is '1' upsdrv_initups... Using subdriver: Belkin HID 0.12 Path: UPS.BELKINConfig.BELKINConfigVoltage, Type: Feature, ReportID: 0x01,

Hi Arjen My apologies fro drifting off topic in the other mailing list...:-) On the bottom of the Belkin UPS unit - is the model number: F6C120auUNV The "au" is for Australia I think. "man belkinunv" states that F6C120-UNV is supported - and I assumed that the "au" would not prevent this. I plugged in the USB to gather the information you requested. My intention

Hi, My platform is Ubuntu 12.04. The hostname is puppet and this is a Virtual Machine in Vmware 5.0. This is a lab server and it is behind a proxy. I am having a problem with the installer. Any ideas what is going on? root@puppet:/home/rbgonza/puppet/puppet-enterprise-2.8.0-all# ./puppet-enterprise-installer

Belkin F6C1200-UNV on Ubuntu 7.04, megatec_usb driver, Every few minutes I get a beep and a "UPS not available" message that seems to be bogus; upsc reports real data, not at complaint that it's stale. Is there some timeout I need to lengthen? Also, shouldn't upsc report the poll time associated with the data it displays? -- >>esr>>

Hello, on an x64 ubuntu 15.10 desktop tinc 1.0.26 sometimes crashes on startup of the machine. eth0 (via good old cat6 cable, no wireless) is configured to use dhcp. The crash does not happen often, I have seen it in total maybe 2 or 3 times since installing 15.10 while it was still in alpha ( July 2015 ) until today. The desktop is not shut down very often, maybe once a week or every two weeks