similar to: Dynamix 1000 VA USB and NUT

Like Glen Ogilvie, I got a newer Dynamix 650 VA with USB connection, and was having trouble getting NUT to communicate with it. This appears to be the UPS that megatec_usb was built for - Vendor: 0x0001, Product: 0x0000, uses Megatec's software, has USB chip attached to internal serial lines, and has terrible USB implementation with fake HID tables. But megatec_usb would consistently fail.

Hi, Has anyone had success with the Dynamix 650VA, that uses the USB cable? I can't get megatec_usb to recognize it, I have tried both stable and development versions. Regards Glen Ogilvie

----- Forwarded Message ---- From: Terry Powling <terrypowling at yahoo.co.uk> To: nut-upsuser at lists.alioth.debian.org Sent: Sat, 27 February, 2010 22:30:05 Subject: trouble setting up kebo-1000d ups (usb) Trying to setup Kebo ups-1000D with usb port. lsusb Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0925:1234 Lakeview Research Bus 002 Device

Hi James, I'm referring to your post here: http://lists.alioth.debian.org/pipermail/nut-upsuser/2010-September/006201.html Have you got by chance any more info on the Dyamix 1000VA model? I was foolish to buy the USB version because it had a better display on the front. Is there any way to get this to go? I have tried all the USB drivers in NUT (on pfsense 2.0RC1) and none do anything

First off, my apologies for bringing back this thread from the dead (September 2005, http://lists.alioth.debian.org/pipermail/nut-upsdev/2005-September/000150.html), however my problem seems relevant enough that I wondered what happened to this thread as it seems to have died after the message I quote below. Despite the fact that I am having trouble getting my Sweex 1000VA UPS (USB) to work, and

First off, my apologies for bringing back this thread from the dead (September 2005, http://lists.alioth.debian.org/pipermail/nut-upsdev/2005-September/000150.html), however my problem seems relevant enough that I wondered what happened to this thread as it seems to have died after the message I quote below. Despite the fact that I am having trouble getting my Sweex 1000VA UPS (USB) to work, and

# /lib/nut/megatec_usb -a myups Network UPS Tools 2.2.0- - Megatec protocol driver 1.5.4 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

Gidday all - I'm a new user to nut. I've got some cheap powerpal UPSs working fairly well. However I also have a new Dynamix UPS-1700D and an old Powercom KIN-1700 something unit that I cannot make work right. The best method I've found is "trial and error" which sounds a bit last-resort. Is there any better way to find out what protocol is used? -- Criggie

Hi, I've got two Dynamix UPS's, both of which are USB and don't seem to work with NUT yet. Can anyone give me some advise on where I should start with working on getting them working. I can do a little C programming, so happy to give things a go but need some guidance. Brian R. Smith (who also subscribes to this list) has one as well. I've attached the output of lsusb -v and

Gidday all - I've got a 1700VA dynamix UPS which is USB. The previous model (with a serial port) worked wonderfully with megatec, but this new one with USB is not working. It feels like the kernel is not handing the USB device properly. The web has not yeilded any useful info. What can I do from here? I'm not sure if its a kernel problem or a UPS config problem, but I'm hoping

Gidday all - I've got a 1700VA dynamix UPS which is USB. The previous model (with a serial port) worked wonderfully with megatec, but this new one with USB is not working. It feels like the kernel is not handing the USB device properly. The web has not yeilded any useful info. What can I do from here? =========================================== [root at hera ups]# lsusb Bus 006 Device 002:

Hello, > Gidday all - I've got a 1700VA dynamix UPS which is USB. > >> You probably need to adapt the files mentioned in this README: >> http://boxster.ghz.cc/projects/nut/browser/trunk/scripts/udev/README Just curious to know if you managed to get the Dynamix 1700UPS communicating with Nut? Thanks. --------------------------------------------------------------------

Hi, I'm at my wits end and need help regarding my UPS. I am a newbie to Linux (10 months) and need help with trying to configure my UPS to my Linux SME server. I have little or no experience with Bash and am finding it overwhelming when it comes to trying to configure my UPS. I have installed my UPS to my Linux SME server and have installed my driver for it. At best I think its running but

sent two 0 byte packets to the driver, then it sent 'URB_FUNCTION_SYNC_REST_PIPE_AND_CLEAR_STALL' down the pipe which seems to come back up as well, and then the UPS turned off. I'll play around later with what happens in that regard, although it may be a bit tricky to figure out when the battery is low without having it plugged in ;-) Also, about nut-usbups.rules.in... The

sent two 0 byte packets to the driver, then it sent 'URB_FUNCTION_SYNC_REST_PIPE_AND_CLEAR_STALL' down the pipe which seems to come back up as well, and then the UPS turned off. I'll play around later with what happens in that regard, although it may be a bit tricky to figure out when the battery is low without having it plugged in ;-) Also, about nut-usbups.rules.in... The

sent two 0 byte packets to the driver, then it sent 'URB_FUNCTION_SYNC_REST_PIPE_AND_CLEAR_STALL' down the pipe which seems to come back up as well, and then the UPS turned off. I'll play around later with what happens in that regard, although it may be a bit tricky to figure out when the battery is low without having it plugged in ;-) Also, about nut-usbups.rules.in... The

Hi Alexander, thanks for your good work on the megatec_usb driver. I have made a few more (cosmetic) changes. Is the driver now working stably for your device? In particular, do the instant commands (and particularly "upsdrvctl -k") work properly? In this case, we could hopefully mark the device as "supported" and merge the driver to the main branch. There is still the

Hi, > I'm at my wits end and need help regarding my UPS. I am a newbie to Linux > (10 months) and need help with trying to configure my UPS to my Linux SME > server. > I have little or no experience with Bash and am finding it overwhelming > when it comes to trying to configure my UPS. > I have installed my UPS to my Linux SME server and have installed my > driver