similar to: Which credentials are used to logon to the upsset.cgi page?

Since there is apparently no immediate solution to upsstats.cgi not reading the output voltage correctly, I have moved on to trying to use upsset.cgi. To recap the UPS is a CyberPower CyberPower CP1500PFCLCD UPS running on a headless server running Slackware 14.1 with the 3.10.7 kernel. The version of NUT is 2.71 and I am using usbhid-ups for communication with the UPS The problem is that when

Bill S wrote, On 4/15/2014 11:18 AM: > The problem is that when I run upsset.cgi I first get a prompt for > user name and password. I then enter the same username and password > as I established in upsd.users and it seems to accept it. upsset.cgi doesn't check that user/password is valid, it just tries it when doing a command. I just tested it, it is working for me on a remote and

The nut ups daemons seem to be communicating with the UPS but upscmd gives me no joy. Running commands do nothing and produce no output. Using the web interface returns an authentication failure and that is the only clue I have. I believe I have everything setup correctly but it's not working. Can someone review this and give me clues as to what I should research next?

On 16/02/14 00:38, Charles Lepple wrote: > On Feb 15, 2014, at 2:57 AM, Tim Dawson wrote: >> The driver will poll the UPS for what variables it supports when it starts, and then go into a polling loop. Look for a section defining the meter map, and you should see the result, as well as the raw data. > Tim: spot on. > > Greg, > > If you want, you can capture the -DDDD output

On Feb 15, 2014, at 6:46 PM, Greg Vickers wrote: > Thanks! I've attached the file to this email (bcmxcp_usb.output2014160926.gz), it ran for 12 seconds, and looks like it's looping by that time. I'm not sure what to look for, does grepping for 'Yes' show the variables that the driver can pull off this UPS? The boolean variables seem to be indicated by "Yes". I

Would you be so kind and provide some examples (commands), please? I would run them today in the evening and report back with the logs. Thank you. Jakub S. On Tue, Mar 10, 2015 at 11:44 PM, hyouko at gmail.com <hyouko at gmail.com> wrote: > mmh.. it looks like someone forgot to hit 'reply all'. > > - relaying the originally attached files (gzipped, minus the two >

Hi, I installed apcupsd through pfsense and noticed some discrepancy with the NUT package. I'm not sure if this is a bug regarding the BATTDATE (apcupsd) and battery.date (NUT) but BATTDATE shows the correct date of 2016/05/11. While NUT shows the battery.date as 2001/09/25 which doesn't make sense. Any ideas? Pfsense 2.4.3-RELEASE-p1 (amd64) NUT 2.7.4_6 NUT installed through

On Jun 7, 2017, at 1:14 PM, Roger Price wrote: > > 2. On the NAS, use command > > upsrw -s battery.charge.low=80 -u upsmaster -s sekret UPS Robbie, The "upsrw" command contacts upsd, so it sounds like you should be able to add a user to upsd.users on the NAS, and then run something like this on the Mac: upsrw -s battery.charge.low=80 -u upsmaster -s sekret UPS at

mmh.. it looks like someone forgot to hit 'reply all'. - relaying the originally attached files (gzipped, minus the two screenshots, to keep size down). 2015-03-09 23:20 GMT+01:00 Jakub Scepka (private) <jakub.scepka at gmail.com>: > Hi everyone! > > Here is summary for our fellows wit the same/similar UPS to save them 3 > weeks of life :) > > First of all I'm

Hello: I have a UPS model MXE II MAXIM brand online, 3500VA 2100W. Connects to the PC by a USB 2.0 port. I wanted to use nut, but this brand is not on the list of nut drivers. lsusb returns: ... Bus 003 Device 003: ID 06DA: 0201 Phoenixtec Power Co., Ltd ... I did not find this manufacturer in the driver list. Anyone know if you can have compatibility with other make and model of UPS. With

2015-03-11 14:21 GMT+01:00 Jakub Scepka <jakub.scepka at gmail.com>: > Would you be so kind and provide some examples (commands), please? > I would run them today in the evening and report back with the logs. First, be sure to have in upsd.users a valid entry to set vars and execute instant commands: [<username>] password = <password> actions = SET instcmds = ALL where

I'm access nut online via localhost. But I have the following problems. When I click on Statistics I get cannot open /etc/hosts.conf. When I click on settings I get: Error: Can't open upsset.conf to verify security settings. Refusing to start until this is fixed. I have .htaccess in cgi-bin with the following: <Files upsset.cgi> deny from all allow from 127.0.0.1 </Files>

Hello list, just a quick email to report that the following UPS was supported (mostly) out of the box: Model: PowerWalker VI 850 LCD Driver: blazer_usb upsc Output (please note I have manually populated the high and low voltages): battery.charge: 100 battery.voltage: 13.50 battery.voltage.high: 13.5 battery.voltage.low: 10 battery.voltage.nominal: 12.0 beeper.status: enabled device.type: ups

>> I am running NUT on a Synology NAS with attached a USB APC UPS. > > Do you have upsd and upsmon running as daemons on the Synology DSM? > Yes I have them both running on the Synology DSM: root 7236 1 0 Jun01 ? 00:00:16 /usr/sbin/upsd root 7741 1 0 Jun01 ? 00:00:00 /usr/sbin/upsmon root 7744 7741 0 Jun01 ? 00:00:12

On 12/03/2016 08:03 AM, Charles Lepple wrote: > On Dec 2, 2016, at 10:23 PM, Jack McGee <jack at greendesk.net> wrote: >> This is new install on Ubuntu 16.04, using packages from Synaptic, >> Network UPS Tools upsd 2.7.2 >> >> I am getting these messages in the terminal: >> Broadcast message from nut at amethi (somewhere) (Fri Dec 2 12:33:03 2016): >>

Thank you for the commands... Please find attached log... Im not sure if the Load.on worked, because in the end I had to manually start the UPS (with button). Anyway, let me know should I need to perform some steps again (probably yes, since I believe it was off). Jakub On 11.03.2015 20:11, hyouko at gmail.com wrote: > 2015-03-11 14:21 GMT+01:00 Jakub Scepka <jakub.scepka at

> On Aug 13, 2018, at 06:17, Charles Lepple <clepple at gmail.com> wrote: > > On Aug 12, 2018, at 11:03 PM, Kevin Mychal M. Ong <kevindd992002 at yahoo.com> wrote: >> >> Hi, >> >> I installed apcupsd through pfsense and noticed some discrepancy with the NUT package. I'm not sure if this is a bug regarding the BATTDATE (apcupsd) and battery.date

Hey guys, :) recently, I installed Cyberpower PR2200ELCDRT2U, however, I have not managed to get this UPS working with FreeNAS 11, yet. According to compatibility list, PR2200 should work fine, when using powerpanel driver: http://networkupstools.org/ddl/Cyber_Power_Systems/ http://networkupstools.org/ddl/Cyber_Power_Systems/PR2200.html However, when trying to establish a connection between

Gabor: note, these HCL reports go to the nut-upsdev list. Begin forwarded message: > From: Gabor Tjong A Hung > Subject: Re: Network UPS Tools - Compatibility List > Date: September 3, 2013 2:18:31 PM EDT > > Sorry, > I just noticed the "If your device isn?t listed" part: > > [HCL] Forza FX-1500LCD supported by blazer_usb > > > [root at freenas] ~#

Hello, we have a Emerson Liebert GXT4, that we like to connect to our servers to shut them down if there is a power failure (which happens quite often in our area). I couldn't get the GXT4 working with usbhid-ups driver. So I need some advise to continue to get this device working. The GXT3 seems to be working ok with NUT (http://networkupstools.org/ddl/Liebert/GXT3.html). Here is my