similar to: Fw: Interfacing a Contact-Closure UPS to Mac OS X and Linux

Hi all RESTORATION of POWER I seem to have cabling & drivers set up correctly for a contact closure UPS ............as below the logs should indicate that. BUT .......... But after power Restoration between commencement of (shutdown -h +20) ....... & execution of (shutdown -h +20) during the 20 minute wait period of shutdown or whatever the "time" variable is.

Hi, I have a Liebert PowerSure Personal XT that I have connected via its USB interface. lsusb shows that it is there and when I plugged in I got the kernel messages: Jul 3 11:25:37 mint kernel: usb 2-2.2: new low speed USB device using address 4 Jul 3 11:25:38 mint kernel: hiddev96: USB HID v1.11 Device [LIEBERT PowerSure Personal XT] on usb-0000:00:10.0-2.2 The documentation suggests that

Hello, I (now) own an Emerson Liebert GXT3 6000VA conected via USB. I've searched the web trying to configure nut (nut-2.6.5-1.el6.x86_64 epel rpm on CentOS 6.3) to monitor the UPS, but couldn't find a successful configuration. I'm running kernel 2.6.32-279.14.1.el6.x86_64. The UPS is connected with an USB cable: Bus 004 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive

Hi all, I?ve a UPS Liebert GXT3 500-3000VA with USB port. I?ve install NUT version 2.2.2 from repository packages for Debian Lenny. Linux kernel 2.6.26 I?ve try to use usbhid-ups driver in ups.conf [liebert] driver=usbhid-ups port=/dev/usb/hiddev0 Debian get the usb: # lsusb -v Bus 001 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive UPS Device Descriptor: bLength

Hello, I need help configuring my USB connected UPS "Emerson Power Liebert PowerSure PSI 1440" to my freebsd machine, using NUT. here's the manufacturer's product page http://www.emersonnetworkpower.com/en-US/Products/ACPower/Pages/LiebertPowerSurePSILineInteractiveUPS10003000VA.aspx I'm not a BSD expert, so please ask me for any information you need. regards Daniele

This patch adds support for the following ups to liebert-hid.c: $ lsusb | grep Liebert Bus 007 Device 005: ID 10af:0001 Liebert Corp. PowerSure PSA UPS Using this patch, I'm able to obtain information about the ups via upsc: $ upsc upsname battery.charge: 100 battery.runtime: 1012 battery.type: PbAc battery.voltage: 1172 battery.voltage.nominal: 12 driver.name: usbhid-ups

I've just upgraded NUT from 2.0.2 to 2.2.0 and have read the upgrading file, which led me to submitting this message. I have changed nut.conf to use 'driver = usbhid-ups' and 'productid = ffff', but I still get 'No matching HID UPS found' when I try to start the driver. The UPS (a Liebert PowerSure Personal XT 450VA) was working fine with 2.0.2 and the hidups

Replaced ups with a new Liebert UPS and it seems the device may not be known to nut. Below is output of lsusb: ID 10af:0002 Liebert Corp. PowerSure PST UPS Sent from Outlook<http://aka.ms/weboutlook> -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20231204/7c08a727/attachment.htm>

Hello everyone, Charles suggested (about a week ago) that I repost to this list. I took a moment to run some additional tests ... The basics: -- UPS: Liebert PowerSure PSA 500 (from the 230 VAC / 50 Hz line) -- Kernel: 2.6.11.5 (from sources), USB support (down to and including CONFIG_USB_HIDDEV) compiled in statically (not as a module) -- Rest of OS: Basically still from the original SuSE

[FAQ on USB-connected UPSes] > Remember: this is brand new *experimental* software and is probably > very broken. Do us a favor and report successes or failures to > the mailing lists. No problem ... : UPS: Liebert PowerSure PSA 500 NUT: Version 2.0.2 Kernel: 2.6.11.5, with CONFIG_USB_HID, CONFIG_USB_HIDINPUT, and CONFIG_USB_HIDDEV compiled in (statically)

please reply to the list. thanks! See below. On Apr 3, 2014, at 3:10 AM, Daniele Borghesi wrote: > thanks for your reply. I'm running the latest version of FreeNAS based on 9.2 with NUT 2.7.1 > > [root at archivio ~]# uname -a > FreeBSD archivio.dannyb78.home 9.2-RELEASE-p3 FreeBSD 9.2-RELEASE-p3 #0 r262572+ > 38751c8: Thu

Hi, I have a Liebert Powersure Personal XT 700 and have followed the installation instructions from here http://www.networkupstools.org/doc/2.0.0/INSTALL.html. I'm pretty sure I've got the ups.conf, upsd.conf and ups.users correct. I have setup upsmon.conf as suggested in the installtion guide with the exception of FINALDELAY which I set to 0 when I found things weren't working

Hi, I have a Liebert POWERSURE PSP connected via USB. Cleanly built and installed from source nut-2.4.3.tar.gz using kernel 2.6.30.5 #cat /proc/bus/usb T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=10af ProdID=0003 Rev= 0.00 S: Manufacturer=Liebert S: Product=Liebert PSP 350 FW: 02 S:

Jochen Bern wrote: > > Peter Selinger wrote: > > have you been able to get your Liebert UPS to work? If I am correct, > > it should work with the newhidups Belkin subdriver. Could you please > > post your results? I am curious to know if this works or doesn't - and > > if yes, we should add permanent support for Liebert into NUT. > > I'm sorry, but

nothing appens. The output is exactly the same as below (attached screen with freenas config) [image: Immagine in linea 2] 2014-04-03 13:16 GMT+02:00 Charles Lepple <clepple at gmail.com>: > please reply to the list. thanks! > > See below. > > On Apr 3, 2014, at 3:10 AM, Daniele Borghesi wrote: > > thanks for your reply.* I'm running the latest version of

Hi Arjen 2007/7/28, Arjen de Korte <adkorte-guest at alioth.debian.org>: > Author: adkorte-guest > Date: Sat Jul 28 16:45:04 2007 > New Revision: 1029 > > Log: > Add Belkin F6C1200-UNV (older model) to supported devices. > > Apparently this is (internally) identical to the F6C1100-UNV. Not surprisingly, they also share the same productid (1100). It also seems to come

Since repeated power cuts last week I've been a bit worried about the state of my server. Today it spontaneously rebooted - but failed to complete. Now it isn't recognising me as a user, by the look of it, so I've got some questions before I do something that might make things worse. I can boot as root, and it appears that all my files are present. System-config-user sees me as user

On Apr 3, 2014, at 7:24 AM, Daniele Borghesi wrote: > nothing appens. The output is exactly the same as below (attached screen with freenas config) > What happens without the leading "-x"? (just "productid=0004") The "-x" is what you would add if you were running the driver from the command line. -- Charles Lepple clepple at gmail

Hi. I have a system with two network cards -- eth0 is a public ip address and eth1 is on an internal network. Now I have all the packet forwards enabled, and there is a route from eth1 to the internal network, but if a computer on the internal network sets his gateway to the box, he can''t traceroute past the box to the internet. There are no iptable rules yet. Here is the routing

I have a 64 bit Gentoo, with a Liebert UPS. The last NUT working version was sys-power/nut-2.4.1-r1 (I also tried sys-power/nut-2.4.3-r2 but downgraded, don't remember the reason). Anyway with the upgrade to sys-power/nut-2.6.0 I started to see this error message when I try to start upsdrv: [root at aemaeth:/etc/nut]$ /etc/init.d/upsdrv start * Starting UPS drivers ... Network UPS Tools -