similar to: Nut with megatec_usb

> Hello everyone. I try to connect four PowerMust 2000 ups's via usb to one > computer using megatec_usb driver. But megatec_usb completly ignores port > directive in ups.conf, I even try port = /dev/null and megatec_usb founds > ups and it works. The 'port' is not used for USB connected devices, it's only needed for compatibility reasons. > Problem is that

I used a brazilian UPS from "TS-Shara" which uses the megatec serial protocol and it works perfectly. Now I have another one from the same brand (TS-Shara) and it uses a USB cable. I found the following: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0483 ProdID=0035 Rev= 2.00 S:

Ok guys I get this errors: Network UPS Tools ? UPS driver controller 2.4.1 Network UPS Tools ? Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 No matching HID UPS found my ups.conf is: [ap1000] driver = usbhid-ups port = auto I?ve also tried to set a specific usb port and change driver. My ups is a AMACROX 1000 http://www.amacrox.com//english/01_product/02_01detail.aspx?pdid=46

I have an UPS, that claims to be IPPon Back Power Pro 700. I'm trying to connect it using USB. lsusb -v says: Bus 1 Device 3: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0

On Feb 18, 2014, at 10:15 PM, Charles Lepple wrote: > On Feb 18, 2014, at 5:55 PM, Thiago Tiedtke dos Reis wrote: > >> Hi, >> >> Recently I got three units of this nobreak [0]: > ... >> [0] http://www.sms.com.br/produtos/Nobreak-SMS/Manager-III-Senoidal > > According to the HCL, for the Manager III, you might want to try the blazer_ser (or in 2.7.1,

Hi nut-upsdev, I have just got OMRON BX35F. Only object files and usage information is included. Where should I start to help you to get it supported? Any interest in supporting it at all?

Hello, i try to setup NUT service to read/control my UPS but without success. Problem is when i try to start "/usr/local/ups/bin/upsdrvctl -DDDD -u root start" i got: /Network UPS Tools - UPS driver controller 2.6.2/ / 0.000000/ /If you're not a NUT core developer, chances are that you're told to enable debugging/ /to see why a driver

Hi, Sometime ago [ June 2018 ] I posted a message about getting trying to get NUT to work with a Power Shield Defender 1200VA UPS. This model appears in the HCL at https://networkupstools.org/stable-hcl.html That UPS reported the following when queried using 'lsusb' on an iMac running macOS [ 10.15 ] Bus 001 Device 008: ID 0665:5161 Cypress Semiconductor USB to Serial Device Descriptor:

Bonjour, Je souheterais utilis? la version qui permet le '-x generic',mais je ne sais pas ou la recuperer car ca devrait solutionner mon probleme (cf mail ci-dessous) DaneZ _____ From: DaneZ [mailto:david.guillotte@danez.no-ip.org] To: arnaud.quette@mgeups.com Sent: Sat, 08 Jul 2006 23:24:06 +0200 Subject: Fw: INFOSEC 500 XP en USB _____ Bonjour Arnaud, Je me

Hi, Has anyone had success with the Dynamix 650VA, that uses the USB cable? I can't get megatec_usb to recognize it, I have tried both stable and development versions. Regards Glen Ogilvie

Hello all: I have a Yukai PowerMust 1000 USB and it used to work on another computer using megatec_usb driver. Now, I have it in a new computer, but the driver does not detect it. It is there: # lsusb|grep Cypress Bus 006 Device 007: ID 0665:5161 Cypress Semiconductor USB to Serial Permissions are OK: # ls -l /dev/bus/usb/006/007 crw-rw-r-- 1 root nut 189, 646 ago 8 01:51

# /lib/nut/megatec_usb -a myups Network UPS Tools 2.2.0- - Megatec protocol driver 1.5.4 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

hi, i've bought a 750VA orvaldi ups http://en.orvaldi.com/index.php/en/product_catalog/product_view/11/162 which holds my hardware (wifi router, cable modem, quad-core with raid and lcd monitor) for ~15 minutes. pretty nice result for a cheap (~57 euro) home ups. in fact, the vendor software for linux is very old (e.g. requires ancient redhat with qt2), requires db9 port while shipped

Hi everybody, In a christmas sequel I've been offered one of the units mentioned above. I've tried to connect it to my Fedora 8 workstation but rapidly concluded it's not yet supported by NUT. So far, I've decompiled the Java classes of the manufacturer's application and noticed that it's most probably yet another kind of serial protocol through the USB. Since

Hi Charles, I'll try the blazer_ser and the nutdrv_qx with version 2.7.1 later. Below, the result of 'lsusb -vvv' requested: Bus 004 Device 002: ID 04b4:5500 Cypress Semiconductor Corp. HID->COM RS232 Adapter Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.00 bDeviceClass 0 (Defined at Interface level)

Hi all, I?ve a UPS Liebert GXT3 500-3000VA with USB port. I?ve install NUT version 2.2.2 from repository packages for Debian Lenny. Linux kernel 2.6.26 I?ve try to use usbhid-ups driver in ups.conf [liebert] driver=usbhid-ups port=/dev/usb/hiddev0 Debian get the usb: # lsusb -v Bus 001 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive UPS Device Descriptor: bLength

I looked through the faq, but couldn't find an answer to this. I'm trying to configure nut-2.0.4-26 on SuSE linux 10.2. In ups.conf, I have [myups] driver = belkinunv port = /dev/undefined desc = "Local UPS" I'm trying to find out what the port should be set to. lsusb shows: Bus 001 Device 005: ID 050d:0980 Belkin Components Device Descriptor: bLength