similar to: powerware 5110 and openbsd

Hello, I have a Yunto e a Zanto ups connected with usb with id 06da:0002 and 06da:0601. I have seen that people had some success using megatec driver. But now megatec is replaced by blazer-usb and I am not able to use my upses under nut. Can you help me? Thanks! Mario

Hi all, I'm currently trying to install a APC Back-UPS ES 700 on FreeBSD. This UPS has a usb connection to the PC and is recognized as: ugen0: APC Back-UPS ES 700 FW:829.D2 .I USB FWD2 rev 1.10/1.06, addr 2 my ups.conf looks like: [back-ups] driver = usbhid-ups port = auto desc = "server" When I now run /usr/local/libexec/nut/upsdrvctl start the output is: Network UPS Tools

Dear Sir, I am attempting to get a Broad Band Modem working on: sony# uname -a FreeBSD sony.family.hom 6.2-PRERELEASE FreeBSD 6.2-PRERELEASE #2: Tue Dec 19 16:55:50 EST 2006 root@sony.family.hom:/usr/obj/usr/src/sys/SONY01 i386 The device is a Sprint PC5740 pc card. When I perform a "man umodem" the card is listed (vendor = Curitel) UMODEM(4)

Hello, I 'm trying to set up an Eaton PW5110 using nut-2.4.1 in OpenBSD, my ups.conf follows : [myups] driver = bcmxcp_usb port = auto desc = "Eaton PW 5110 (1500VA)" My first attempt to run upsdrvctl ended up complaining about unimplemented usb_clear_halt() in libusb. I patched libusb-0.1.12 with the following patch :

(Sorry, I accidentally discarded the wrong message in the moderation queue - please subscribe to the list to avoid this in the future.) > From: <onyx at netfusion.fr> > Subject: [HCL] MGE Pulsar Evolution 1100 - not recognized by USB driver > Date: December 22, 2011 12:15:16 AM EST > To: <nut-upsuser at lists.alioth.debian.org> > > > Hi everybody, > > It

I am looking at the newhid driver for this Pulsar EXtreme here but it gives odd results, for example there is no status variable :) eg debug level is '2' Checking device (0463/FFFF) (/dev/usb0//dev/ugen0) - VendorID: 0463 - ProductID: ffff - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: /dev/usb0 Trying to match device Device matches HID descriptor retrieved

Hi all! Maybe possible adds something in megatec_usb driver for normal working with ippon 2000? This is output for drivers megatec_usb and blazer_usb: =========================================================== gate# /usr/local/libexec/nut/megatec_usb -DDDD -a IPPON Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '4' Checking

Howdy, I had this working with lots of help for a developer before (Charles Lepple), but after upgrading to a somewhat more current version of FreeBSD the patched-up version stopped working. Seeing as this was more than a few years ago, I thought I'd give a new libusb and NUT a try to see if it might work out of the box. So far, no luck. Some info: FreeBSD 6.3 libusb 0.1.12 NUT 2.4.1

I'm running FreeBSD 6.2 with Nut 2.0.5 installed from ports... I have a TrippLite OmniVS1500XL plugged in, but I'm having little luck with the tripplite_usb module. I have already built and booted a new kernel with UHID disabled so that libusb can grab /dev/ugen0. At first I was able to get the following out of the driver: # USB_DEBUG=5 /usr/local/libexec/nut/tripplite_usb -u root

Hallo, Following the tips found at https://calomel.org/nut_ups.html I was trying to make NUT operate "APC Back UPS CS-350". The device introduces itself as: #v+ ugen0 at uhub0 port 1 "American Power Conversion Back-UPS CS 350 FW:807.q7.I USB FW:q7" rev 1.10/0.06 addr 2 #v- My config: #v+ [apc] driver = usbhid-ups port = /dev/ugen0.00 pollfreq =

Hallo, Following the tips found at https://calomel.org/nut_ups.html I was trying to make NUT operate "APC Back UPS CS-350". The device introduces itself as: #v+ ugen0 at uhub0 port 1 "American Power Conversion Back-UPS CS 350 FW:807.q7.I USB FW:q7" rev 1.10/0.06 addr 2 #v- My config: #v+ [apc] driver = usbhid-ups port = /dev/ugen0.00 pollfreq =

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to

Hi, I have an MGE Ellipse UPS connected to a FreeBSD 7.0 system and it works OK to begin with but after an hour or so it dies, eg.. Starts out OK.. debug level is '2' upsdrv_initups... Checking device (0463/FFFF) (/dev/usb2//dev/ugen0) - VendorID: 0463 - ProductID: ffff - Manufacturer: MGE UPS SYSTEMS - Product: ELLIPSE - Serial Number: 000000000 - Bus: /dev/usb2 Trying to match device

[It seems the last time this came up was in march, under the heading of "Sony Cybershot should be in hardware notes". This message is intended mainly to document what I've managed to track down.] The m500s still will not sync with pilot-link 0.11.7 in -STABLE. An easily triggerable panic is another issue [1]. The pilot-link code first opens /dev/ugenX and then switches to

Yes I do have Linux. I have assigned the ups.conf file as seen below.. [testups] Driver = usbhid-ups Port = /dev/ttyUSB0 When I try to start the ups driver I get the following error... $ sudo upsdrvctl start Network Ups Tools - UPS driver controller 2.7.1 Network Ups Tools - Generic HID driver 0.38 (2.7.1) USB communication driver 0.32 No matching HID UPS found Driver failed to start (exit

Hello all, I am trying to set up my brother's UPS (remotely over internet) on an OpenIndiana-based storage box. According to him, the UPS is probably an Ippon Back Power Pro 600 dated around 2003 (battery recently replaced), and it has an USB connection. Sorry for a relatively long post with a log of my successes and failures, in the hopes that someone would point out what I did wrong.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Just a little patch for the drivers.list The "Cyber Power Systems Intelligent Series CP1500EAVRLCD" ups http://eu.cyberpowersystems.com/products/ups_systems/intelligent/cp1500eavrlcd.htm Got one here running (see: https://nut.stillbilde.net/cgi-bin/nut/upsstats.cgi?host=CyberPower at upsmonitor) Works flawlessly. Patch as follows:

Hi, I own a Yunto-Q 700 (made 2000 by online usv systems) and a Yunto-Q 1200 (made 2010). They both work with blazer_ser, but didn't shutdown. I straced the proprietary driver and found the ups expected the return time given with _5_ digits instead of 4, else the command was ignored by the ups. And the Yunto don't send rating/manufacturer informations. I don't want to commit this to

Hello, I'm facing problems as I'm installing NUT to monitor a MGE Ellipse ASR600USBS on a FreeBSD 6.1 box. UPS is recognized as : ugen0: MGE UPS SYSTEMS ELLIPSE, rev 1.10/42.41, addr 2 I'm temporarily using root profile (devfs/devd scripts not modified atm). newhidups starts & runs fine (unplugging mains makes newhidups outputs lots of data when started with -DDDD flags)