similar to: Ippon device does not work

I recently took over maintenance of a linux computer which is drawing power from a "Maruson Power Net 1500" UPS. However, there is currently no monitoring or control of the UPS by this (or any other) computer. Can nut control this device? There are serial, usb, and EPO connectors on the back of the unit. (There may be a manual but I'm going to have to hunt for it.) Thanks, David

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

I recently bought a Belkin F6H375 UPS. It connects to the computer via USB. Searching the Internet led me to believe that the megatec_usb driver in nut supports this UPS, however I've been unable to get it to work. I have this in ups.conf: [belkinusb] driver = megatec_usb port = auto desc = "Belkin USB" Here's what happens when I try to use it: ~ #

Hello everyone, has anyone ever tried to make this device work with Linux and NUT? This is what udevadm monitor says: UEVENT[1215983089.652345] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1 (usb) UEVENT[1215983089.652427] add /class/usb_endpoint/usbdev1.4_ep00 (usb_endpoint) UEVENT[1215983089.657975] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1/1-1:1.0 (usb) UDEV

Hi nut-upsdev, I have just got OMRON BX35F. Only object files and usage information is included. Where should I start to help you to get it supported? Any interest in supporting it at all?

Greetings Gentlemen, I have Mustek NetGuard 1000 UPS which is equivalent to Ippon SmartWinner 1000. I have tried to run several latest builds of NUT, but run megatec_usb driver still failed with my device. I hope the information below might help. Regards, Oleg Here is the information which may help: lsusb -v Bus 002 Device 002: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor:

So, I have this Mustek Powermust 600USB (no serial port) here temporarily. It seems to be a hid device. The output from "lsusb -v" and "newhidups -DDDDD" (with "generic" and "vendorid=06da") are (respectively): ----------------------------------------------------------------------------------------------- Bus 001 Device 002: ID 06da:0003 Phoenixtec Power

Roman, I don't think I already asked, but could you post the output of lsusb -v -d 06da:0003 Just to be sure that we're not exceeding some buffer limitations of the device. Best regards, Arjen -- Please keep list traffic on the list

A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 188 bytes Desc: not available Url : http://lists.alioth.debian.org/pipermail/nut-upsdev/attachments/20071124/3ceb35d2/attachment.pgp

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day to all. In one of the offices I'm administering there are about 15 UPS marked with the brand "Ippon BackPro". This brand is widely popular in Russian Federation, while by itself is a 'Made in PRC' megatec clone. Depending on the model this UPSes have got either one standard serial RS-232C interface (cheaper models like

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

I used a brazilian UPS from "TS-Shara" which uses the megatec serial protocol and it works perfectly. Now I have another one from the same brand (TS-Shara) and it uses a USB cable. I found the following: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0483 ProdID=0035 Rev= 2.00 S:

Hello. I've been experimenting with the USB connection of an Ippon BackComfoPro 800. This is the device "06da:0003 Phoenixtec Power Co., Ltd". The current SVN version of NUT does not work with this device. The megatec_usb driver can't get a proper reply to a Q1 request, failing with an error message about "short read (14 bytes)" instead. I have found the reason for

Hi all! I have a ups Ippon smart power pro 2000. And it connects to my FreeBSD 7.2 x86 server throught usb. I'm try to setup it in nut with megatec_usb driver... But it is not recognizes ups. I'm try set productid and vendorid in ups.conf, but this is not help. Nut version 2.4.1 below i'm add output of lsusb, my ups.conf and /usr/local/libexec/nut/megatec_usb -a IPPON -DDD

Ok guys I get this errors: Network UPS Tools ? UPS driver controller 2.4.1 Network UPS Tools ? Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 No matching HID UPS found my ups.conf is: [ap1000] driver = usbhid-ups port = auto I?ve also tried to set a specific usb port and change driver. My ups is a AMACROX 1000 http://www.amacrox.com//english/01_product/02_01detail.aspx?pdid=46

Hello, I have a Yunto e a Zanto ups connected with usb with id 06da:0002 and 06da:0601. I have seen that people had some success using megatec driver. But now megatec is replaced by blazer-usb and I am not able to use my upses under nut. Can you help me? Thanks! Mario

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Hi, Has anyone had success with the Dynamix 650VA, that uses the USB cable? I can't get megatec_usb to recognize it, I have tried both stable and development versions. Regards Glen Ogilvie