similar to: Debugging problem AFTER the failure?

Hello again! I'm yet again the guy from the blazer_usb problem and the ATCL one too. This time I have a third UPS (the last one In my collection) that i'm trying to make work instead of the ATCL one since there's no driver for it on windows. This UPS is another no-brand box (actually it is a "kozumi", but that's just a rebrand), and apparently it's much more basic

I tried to find a search button for the mailing list but could not. So rtfm me with the link please. If not.. I have an old Deltec PowerRite Pro 2 UPS which has a 9 pin serial cable. By trial and error Im pretty sure I found LB = DCD, but can not get the combination for OB / OL. No matter what I do I get the results below. driver.name: genericups driver.parameter.CP: CTS driver.parameter.LB:

Hi, Anyone have any experience with these ??? http://cgi.ebay.com/UPS-1000VA-Brand-New_W0QQitemZ280141461506QQihZ018QQcategoryZ99265QQssPageNameZWDVWQQrdZ1QQcmdZViewItem Thanks, Tuc

I'm forwarding this to the list, as I'm not quite sure what's going on here. Never seen this on Linux, don't know if it is a FreeBSD thing or not. ---------- Forwarded message ---------- From: Herman J van der Merwe <herman@mercygate.com> Date: Feb 11, 2007 9:50 PM Subject: NUT on FreeBSD To: carlos.efr@mail.telepac.pt Hello Carlos Maybe you can assist me with NUT 2.0.5

Hello, I am trying to understand how to create a custom configuration for the genericups driver. My system simply signals RI on a serial port on low battery. That's it, nothing else. This serial port is also being used for communications so the other lines are going to be changing all the time, unrelated to the UPS state. Is there a "null" upstype I can use, and then add LB=RNG?

I'm running a freebsd 6.2 system and built the nut port. I cannot seem to connect to serial com1 or 2 /usr/local/etc/nut> upsc apcBK500 at localhost Error: Connection failure: Connection refused My configs: ups.conf ----------------------- [apcBK500] driver = genericups upstype=20 port = /dev/cuad1 upsmon.conf -------------------------- MONITOR apcBK500 at localhost

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

Hi All, I'm new to Nut and had been looking for a way of monitoring a small UPS we have just designed. We are using simple contact closure circuit, but I don't appear to be able to get the Genericups driver to work. I've followed the documentation and have decided to try the APC upstype = 1 If I type 'genericups -x upstype=1 /dev/ttys0' , I get an error: 'Fatal error:

I am working with a number of our customers to ensure that NUT works with different UPS's on Freebsd 9.1. The current one I am looking is support for: *Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower* What seems to be supported in Freebsd is: CXR1000 blazer_ser LAN Saver 600 genericups upstype=0 Power Guardian genericups upstype=7 PrOffice 650 USB blazer_usb DS-800 USB

Paulo Tiago Serr?o wrote: > Unitek Alpha 500 inT (it's an Internal UPS) > > Works fine with genericups upstype=4 (Its comes with a RUPS software CD). > > !!!Doesn't work with fentonups (Instant reboot upon nut launch)!!! you should test the new megatec driver. Dig a bit the user list, and get the latest subversion trunk... > PS: maybe it was worth to add a link in the

On Jun 20, 2013, at 9:48 PM, Reed Hedges wrote: > UPSPORT=/dev/ttyS0 > > # type cablep kill t powerok battok cableok > robot --- RI 0 /RI --- --- > ? > > Is there an equivalent of ?---? in genericups? I think it's pretty much any value other than a valid

Hello, I have one UPS Infosec XP Pro 2500 RM and it works with windows sw RUPS2000. Now I want to install this UPS as virtual server on vmware ESXi vMA - (SUSE SLES 11SP2 linux). On this linux I have NUT 2.6.0 and I stopped now with configuration of genericups driver. Working cable (direct cable pin1-pin1 ... pin9-pin9) connection on Windows: PIN | PC | UPS

It look to me that overwriting UPSTYPE CP signal or polarity in ups.conf have no effect. Looking at drivers/main.c source show that &upstab[upstype].line_norm is set to custom CP in initinfo() only _AFTER_ the serial signals are actually set by upsdrv_initups().

It look to me that overwriting UPSTYPE CP signal or polarity in ups.conf have no effect. Looking at drivers/main.c source show that &upstab[upstype].line_norm is set to custom CP in initinfo() only _AFTER_ the serial signals are actually set by upsdrv_initups().

Thx for the info Charles. Here is what I am seeing from 'usbconfig list' ugen0.1: <EHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen0.2: <product 0x0024 vendor 0x8087> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.2: <product 0x0024 vendor

On Jan 31, 2014, at 3:14 PM, Chris Duffy wrote: > The current one I am looking is support for: > > Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower > > What seems to be supported in Freebsd is: Small clarification: the hardware compatibility list isn't broken down by operating system (theoretically, the drivers should work on any POSIX system, with additional

Hi everybody, I've got an Unitek iZi UPS 525 with a serial interface. The supplied cable looks fairly simple: RX->RX , TX->TX and GND->GND. Using this cable and Minicom with 2400 8N1 I'm able to issue commands to the UPS using the "Megatec Protocol" http://www.networkupstools.org/protocols/megatec.html so I know the UPS is fairly "intelligent" :-) and the

Hi, is there a way to use my Belkin F6H650 on the USB port? I already installed usbhid-support, but neither the hidups worked (reports "/dev/usb/hiddev0 is not a UPS") nor genericups with upstype=7 and the hiddev set as device ("ioctl TIOCMSET: Invalid argument") worked. I have installed the debian sarge package of nut 2.0.1 (2.0.1-4) Regards, Philipp