similar to: problems getting chan_alsa.so to run

I have just installed the Alsa drivers for my 2.4.18-14 kernel (RH8). I have configured the sound card ok with alsaconf and tested with the aplay , works fine. But when I run asterisk it says.. ------------------------------- [chan_alsa.so] => (ALSA Console Channel Driver) Apr 20 18:28:34 ERROR[8192]: chan_alsa.c:339 alsa_card_init: snd_pcm_open failed: No such device or address Apr 20

asterisk-1.4.7, Fedora 7, intel emt64 - nocona: == Parsing '/etc/asterisk/alsa.conf': Found ALSA lib pcm_dsnoop.c:558:(snd_pcm_dsnoop_open) unable to open slave [Jul 15 10:12:23] ERROR[24420]: chan_alsa.c:365 alsa_card_init: snd_pcm_open failed: No such file or directory [Jul 15 10:12:23] ERROR[24420]: chan_alsa.c:481 soundcard_init: Problem opening alsa I/O devices == No sound

Hi, I want to use asterisk with jack audio. I tried the next configurations : 1 ) app_jack.so -> does not work. 2 ) chan_alsa.so without jackd started my .asoundrc : pcm.!default { type hw card 1 } pcm.jack1 { type jack playback_ports { 0 alsa_pcm:playback_1 1 alsa_pcm:playback_2 } capture_ports { 0 alsa_pcm:capture_1 1

alsa_card_init^[[0m: snd_pcm_open failed: Connection refused soundcard_init^[[0m: Problem opening alsa capture device These are the errors I get. I changed the following: chown -R myuser:myuser /var/log/asterisk chown -R myuser:myuser /var/lib/asterisk chown -R myuser:myuser /var/spool/asterisk chown -R myuser:myuser /var/run/asterisk chown -R myuser:myuser /usr/lib/asterisk edited

I am using alsa with asterisk. The asound.conf is below. When I start asterisk with /etc/asound.conf present I get errors on the console that: chan_alsa.c:304 alsa_card_init: snd_pcm_open failed: Invalid argument If I remove the asound.conf asterisk starts up and works. However I NEED the asound.conf for another application. What might be the issue here? THanks jerry /etc/asound.conf

>>I'm not sure that your question is clear. You'll probably want to be more specific. >> What is pulse? You mention "as a user", are you talking about voicepulse.com ? >> What are you trying to do with pulse? >> What problem are you running into? Sorry Rusty... I am trying to get Asterisk 11 to co-exist with a centos 7 box that has pulse audio running as

All, I'm trying to setup asterisk to run off of a raspberry pi and use the alsa module to access the sound card (a usb logitech 270 camera/mic). Everything appears to be working except the audio quality is very (very) poor and there is an error from the asterisk conosle: Loading chan_alsa.so. == Parsing '/etc/asterisk/alsa.conf': Found [Sep 6 17:57:29] WARNING[4562]:

I am trying to connect audio through HDMI on a config. aplay - l gives: **** List of PLAYBACK Hardware Devices **** card 0: NVidia [HDA NVidia], device 0: VT1708B Analog [VT1708B Analog] Subdevices: 2/2 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 card 0: NVidia [HDA NVidia], device 3: NVIDIA HDMI [NVIDIA HDMI] Subdevices: 1/1 Subdevice #0: subdevice #0 So I change my

Index: channels/chan_alsa.c =================================================================== RCS file: /usr/cvsroot/asterisk/channels/chan_alsa.c,v retrieving revision 1.2 diff -r1.2 chan_alsa.c 1042c1042 < if ((cfg = ast_load(config)) { --- > if ((cfg = ast_load(config))) { -- Michael Bielicki Managing Director TAAN Consultants Ltd http://www.global-gateway.net/

>> See if it plays back properly. > > Running aplay as asterisk user seems to be no problem: > > asterisk at puppy$ aplay /usr/share/sounds/alsa/Front_Center.wav > Playing: WAVE '/usr/share/sounds/alsa/Front_Center.wav' : Signed 16 bit > Little Endian, Rate: 48000 Hz, mono > asterisk at puppy:~$ aplay -Dpulse /usr/share/sounds/alsa/Front_Center.wav >

Hi I?m a new user and I do test with my hardware . I have a x100p and telephone vozip. And when I run this command asterisk ?vvvvc for to test it . My computer show it ?warning? [chan_iax.so] => (Inter Asterisk eXchange) == Manager registered action IAX1peers == Parsing '/etc/asterisk/iax1.conf': Not found (No such file or directory) Apr 2 07:45:12 ERROR[16384]:

Hi people! I am looking for a h.323 implementation guide for asterisk. I looked in the doc folder of the latest asterisk source distribution and I didn't fund anything acording to this subject. If you guys could give me any advise, I would thank you. Tamer

Hi! I have problems building asterisk 1.6.0.6. ./configure --prefix=/usr make gets me: enerating embedded module rules ... [CC] extconf.c -> extconf.o In file included from /usr/local/include/datatypes.h:50, from /usr/local/include/err.h:49, from extconf.c:45: /usr/local/include/integers.h:50:67: error: srtp_config.h: No such file or directory In file

Joshua Asterisk 18.14.0 with chan_alsa and Console/dsp works. This does not work in 18.18.0 with chan_console enabled. I am on Ubuntu 20.04 LTS. Is there a howto for the new chan_console ? how can I get this working again ? I am trying to just play audio on pulse audio. Thanks, Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

On Thu, Sep 7, 2023 at 3:15 PM Jerry Geis <jerry.geis at gmail.com> wrote: > Joshua > > Asterisk 18.14.0 with chan_alsa and Console/dsp works. > This does not work in 18.18.0 with chan_console enabled. > I am on Ubuntu 20.04 LTS. > > Is there a howto for the new chan_console ? > I'm not aware of one. The module itself has existed since at least Asterisk 1.8

If anyone else is trying to use asterisk with the sound port AND use something else like mplayer my experience was asterisk BLOCKS the port. I added a bug item this morning to suggest a parameter control in alsa.conf and 1 line program change to chan_alsa.c of: snd_pcm_nonblock(handle, 1); Note this will always set NONBLOCK which is what I want at this time. The paramter in alsa.conf is more

Hi some problem with chan_alsa. Depending on the configuration I don't get any sound output (output_device not set in alsa.conf - same as output_device=default) or very strange output (output_device=hw:0,0) when dialing into something like exten => 10,1,Answer exten => 10,n,Playback(soundfile) exten => 10,n,Hangup Other alsa applictions do work without problems and for example this

I am using asterisk 1.4.21and svn-124910 and getting the chan_alsa:693 resource temporarily unavailable message. The audio is working but I dont recall getting any error message in the past. Is this something to be concerned about? Jerry

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the