similar to: SS7 and PRI compatibility

>Freddi Hansen wrote: >> with boards from Aculab, we are replacing Aculab boards with Digium >> boards BUT we would need more >> Digium boards IF we could use both Digium and Aculab cards in the same >> server. The reason being that >> TE410P doesn't support SS7-ISUP so we continue using only Aculab cards >> in the servers that must support >>

Hey All, I'm just daydreaming here.. but what's the status of SIP-T in Asterisk? I haven't been able to find a whole lot of info on SIP-T but seems like just an extension of SIP. Right? Now if I had a PSTN Gateway (that is a SS7 gateway) that supported SIP-T, could I signal * with SIP-T from it and have asterisk utilize MGCP to sieze a particular DS0 on a remote DS1? Hmm.. What am

Hello, There are some parameters in the ISUP data (coming into the network via SIP-T packets) that need to be translated into SIP headers to be used by asterisk for proper call routing. What gateways are available to accomplish this? Thanks, Elliot -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello! I have a sip device that is sending in the SDP: rtpmap:98 g729a It does not seem like Asterisk is negotiating the codec properly, because while the call rings, the rtp lines fail. However, on other sip devices that have "rtpmap:18 g729" in their SDP, things work fine with Digium's commercial g729 license. How do I get "98 g729a" recognized by Asterisk? Thanks,

Hi, Would just like to inquire if anyone here has a setup of asterisk to send traffic to AS5400 connected to an SS7-PRI.? this is more of a AS54 question, as i've been reading and i always stumble upon PGW2200 as a requirement to handle SS7 signaling on the AS54. Has anyone able to send calls from asterisk to an as 54 with SS7-PRI without PGW2200? TIA Regards, Nhadie --------------

> > >On Thu, 2003-11-13 at 16:50, Freddi Hansen wrote: > > >>>> >Freddi Hansen wrote: >>> >>> >>>>> >> with boards from Aculab, we are replacing Aculab boards with Digium >>>>> >> boards BUT we would need more >>>>> >> Digium boards IF we could use both Digium and Aculab cards in

hi can someone recommend a book about ISDN and SS7? I've been hacking asterisk for a while, but it'd be good to get some better background within things... thanks roy

Hi all, what is the signalling of IAX? Currently I want to connect two switch through IP using asterik signaling, and I want to transfer SS7 over IP (between the 2 asterisk), will IAX can transfer SS7 signalling through IP (like TDMoIP does) If no which solution can I use? see below the architecture switch1-------------Asterisk--------------------------Asterisk --------------------------Switch

Hello! What kind of sms text messaging capabilities does Asterisk have? I do not know very much about about SMS technology, but I am looking for the following features: 1. mobile SIP devices can send and receive SMS messages 2. Asterisk server be able to accept and send SMS messages through PRI lines and Internet connections. I noticed that Asterisk has an SMS function, but I am not farmiliar

Hello! I have a 64 bit Asterisk system and am wondering how to use Digium's 32 bit fax driver. Is there some kind of emulation that can be used? Thanks! Elliot -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090604/b7f1d6c4/attachment.htm

Hello! I am having an odd problem in that when the caller dials extension "2" in a dialplan, the system waits 3 to 4 seconds before proceeding. This doesn't happen when any other other extensions are dialed, including an identical dialplan on other another extension! Is this a bug? Later, Elliot

Hello Everybody! I am currently setting up an Asterisk server for medium to high load (approximately 20-35 concurrent phone lines). Do you think the following specs will sufficiently satisfy this system? CPU: XeonQC3220 2.4GHZ 8M RAM: 2X2GB/800 Harddrive: 1X250GB I could add harddrives and partition them into /var and /log directories to help with diskdrive throughput. Thanks! Elliot

I thought everyone should know this. Jorge, After reading your page in the http://voip-info.org/tiki-index.php?page=Asterisk+SS7 please advise Your U.S. customers that SS7 is not done the same way as in the rest of the world and the requirements are different. The U.S carrier's require 2 redundant links. I know this first hand because we run an SS7 network. CARDOSO Jorge Miguel wrote:

Hi All, I want packets [request/response] capture for ISUP packets , i have E1 line terminated to my digium card i just want a packets flow between my machine and teleco side, is any tool or utility [command] availabele for observation this packets and data. any help appericiated Thanks Dhaval -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hi all, I am having this problems for a while and could not figure out the cause of this. I have FreePBX version of Asterisk (1.8.11-cert) routing calls to 10 different FreePBX servers (same version of Asterisk) depending on the destination numbers. The incoming calls into the main Asterisk server with 4 x Sangoma A102 E1 card are coming through a SS7 link from an ISUP interface of a

When are 'we' going to have this solution Steve? :) You keep talking about it, and we keep asking when it's going to come about. I know myself, SS7 will be a make or break for our continued use of Asterisk. Even if we had some price indications would be good, and/or a timeframe? Don't want to seem pushy, but it's been on the cards for quite some time now. Ben -----Original

I'm making outbound calls by placing call files in the asterisk outgoing directory. At times, the call would be hung by SS7 without even attempting (due to error in the outgoing number). I get the following on console: -- Attempting call on ss7/9297210213 for s at croom:1 (Retry 1) -- Sent IAM CIC=22 ANI=9134904821 DNI=9297210213 RNI= -- SS7 hangup 'SS7/callserver/22'

Hi all, I'm being requested to deploy an?IVR service?using SS7. I've deployed Asterisk before using ISDN connection, but never with SS7. Can anyone explain me the different between using ISDN and SS7 ? What need I do now to change to use SS7 ?. Many thanks, Giang -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page