similar to: Digium HA8. Does settings order matters (in system.conf) ?

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

Hi, On a (bogus) system equiped with a Digium HA8 and 8 BRI ports, I'm reading this: # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO HA8-0000 RED 109 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) HA8-0000 UNCONFI 109 0

2011/6/14 Kevin P. Fleming <kpfleming at digium.com> > On 06/14/2011 03:11 PM, Olivier wrote: > >> Hi, >> >> 1. Is there any manual entry about modprobe's options relative to a >> given Dahdi driver (wctdm24xxp, for instance) ? >> >> 2. When loading a wctdm24xxp driver, is there any parameter to pass to >> modprobe to configure a span in

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

I just installed a TE820 octal span T1 card, and it's not showing up in dahdi_hardware output. This was installed into a test machine that already has a TDM800P card in it, and that one is showing up and working fine. Is there some kernel module that I'm missing? Lspci: 05:04.0 Ethernet controller: Digium, Inc. Wildcard TDM800P 8-port analog card (rev 11) 21:08.0 Communication

2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > Hello, > > > > After all these years installing from source, I'm giving Dahdi package > > installation a try on a recent Stretch box. > > > > Google over the web, I didn't find too many doc on this topic. >

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

2017-03-14 15:26 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > On Tue, Mar 14, 2017 at 02:58:07PM +0100, Olivier wrote: > > 2017-03-14 13:08 GMT+01:00 Tzafrir Cohen <tzafrir.cohen at xorcom.com>: > > > > > On Tue, Mar 14, 2017 at 11:10:57AM +0100, Olivier wrote: > > > > Hello, > > > > > > > > After all these years

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

Hi, I know this may sound a bit silly but, given some asterisk issue are still open (see http://issues.asterisk.org/jira/browse/ASTERISK-13176 for instance), I'm wondering if there is a recommended way to configure an used port from a Digium HA8 + B400M board. At the moment, my console is full with messages such as : [Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No

Hi, I've run into a veird problem. I'm using a B400P BRI and an A1200P card with dahdi (2.2.1) driver. The dahdi_scan shows the each moduls and spans, everything seems fine. With dahdi_genconf I made the config, set up the channels in chan_dahdi.conf, but after reboot, the two card changes the order, (originaly the B400P is the first (closer to the processor) and A1200P is the

2011/6/15 A J Stiles <asterisk_list at earthshod.co.uk> > On Wednesday 15 Jun 2011, Olivier wrote: > > At the moment, my console is full with messages such as : > > [Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No > > D-channels available! Using Primary channel 9 as D-channel anyway! > > [Jun 15 09:06:25] WARNING[2141]: chan_dahdi.c:3369

Hi, I'm having some questions related to echo cancellation configuration on a Digium board enabled systems (B410P, TE420, TE420B, ....) for cases when a hardware ech canceller is present or not. I read in TEXXX manual that when setting echocancel=yes in chan_dahdi.conf on a VPMOCT64-equiped system, 128ms hardware echo cancellation was enabled. 1. I'm correct thinking that it is then

Dear, I have Asterisk 1.6 with an E1 Digium card with echo cancellation module. So I need to use just the echo cancellation by hardware and disable the echo cancellation by software. I use DAHDI for my telephony hardware. If the lines involved with echo cancel are: In /etc/dahdi/system.conf: echocanceller=mg2,1-15,17-31 In /etc/asterisk/chan_dahdi.conf: echocancel=yes echocancelwhenbridged=no

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

Dear all, i have a problem with a system running - Ubuntu 10.04 ( all updates done ) - ii asterisk 1:1.8.5.0-1digium1~lucid Open Source Private Branch Exchange (PBX) - ii asterisk-dahdi 1:1.8.5.0-1digium1~lucid DAHDI devices support for the Asterisk PBX I also use freepbx 2.9 for the configuration. Hardware is a Dell R410 and a Digium

Hi, I've been getting regular CPU usage spikes(50%-80%), due to asterisk (according to top). I never noticed this on 1.4, and I have top running in the background pretty much all the time. In between those spikes Asterisk stays under 10% CPU usage (I have a transcoder card, which helps). It's very regular, never any missed spike, or any spike in between the regular spikes. I

I have a server with an asterisk ss7 link connected to a Siemens working well for over a year. A few days ago I started having problems with signaling. I found the following logs in / var / log / messages Sep 12 11:49:25 call3 kernel: [1018427.030959] dahdi: Master changed to TE2/0/2 Sep 12 11:49:25 call3 kernel: [1018427.120740] dahdi: Master changed to TE2/0/1 Sep 12 11:49:26 call3 kernel:

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done