similar to: How to set a HA8 board + B400M in NT mode ? [SOLVED]

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hi, I know this may sound a bit silly but, given some asterisk issue are still open (see http://issues.asterisk.org/jira/browse/ASTERISK-13176 for instance), I'm wondering if there is a recommended way to configure an used port from a Digium HA8 + B400M board. At the moment, my console is full with messages such as : [Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

Hi, I'm reading Digium HA8 manual (page 55). It lists several parameters that can be used to configure a BRI port. More precisely, it suggests that : Term, is the last parameter NT/TE is the one just before (starting from the end). If I'm not mistaken, it seems dahdi_genconf generates /etc/dahdi/system.conf files in which both parameters order is reversed : # Span 1: WCBRI/0/0

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0-rc1 DAHDI-Tools-v2.7.0-rc1 dahdi-linux-complete-2.7.0-rc1+2.7.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: *

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0-rc1 DAHDI-Tools-v2.7.0-rc1 dahdi-linux-complete-2.7.0-rc1+2.7.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: *

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0 DAHDI-Tools-v2.7.0 dahdi-linux-complete-2.7.0+2.7.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: * Driving closer

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0 DAHDI-Tools-v2.7.0 dahdi-linux-complete-2.7.0+2.7.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: * Driving closer

2011/6/15 A J Stiles <asterisk_list at earthshod.co.uk> > On Wednesday 15 Jun 2011, Olivier wrote: > > At the moment, my console is full with messages such as : > > [Jun 15 09:06:25] WARNING[2140]: chan_dahdi.c:3369 pri_find_dchan: No > > D-channels available! Using Primary channel 9 as D-channel anyway! > > [Jun 15 09:06:25] WARNING[2141]: chan_dahdi.c:3369

Hi Olivier It seems wrong configuration, because according to your mail Asterisk it will be acting as terminal mode (ie Patton gateway acting as network and asterisk as terminal). But Asterisk message is indicated Asterisk a s a NT mode [ 212.226050] wctdm24xxp 0000:0a:01.0: xhfc: Configuring port 0 span 1 in NT mode with termination resistance ENABLED. It could help by checking parameters on

Hi all, I'm getting compilation error as trying to install latest version of dahdi on CentOS box 5.9 which I now updated from 5.6. I also installed the dependencies but still not getting the clue to get install the driver. Listing down the errors below; CC [M]

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2-rc1 DAHDI-Tools-v2.9.2-rc1 dahdi-linux-complete-2.9.2-rc1+2.9.2-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete This release is

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2-rc1 DAHDI-Tools-v2.9.2-rc1 dahdi-linux-complete-2.9.2-rc1+2.9.2-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete This release is

2010/12/1 Shaun Ruffell <sruffell at digium.com> > On 12/01/2010 11:00 AM, Shaun Ruffell wrote: > > On 12/01/2010 09:56 AM, Olivier wrote: > >> I'm facing an issue with which loading wctdm24xxp module fails. > >> [ 33.527942] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive > frame. > >> [ 33.527995] wctdm24xxp 0000:01:0b.0: The firmware

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2 DAHDI-Tools-v2.9.2 dahdi-linux-complete-2.9.2+2.9.2 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * Mostly stability patches affecting

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2 DAHDI-Tools-v2.9.2 dahdi-linux-complete-2.9.2+2.9.2 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete * Mostly stability patches affecting

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.9.2-rc2 DAHDI-Tools-v2.9.2-rc2 dahdi-linux-complete-2.9.2-rc2+2.9.2-rc2 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete This release is